Vivo MOUNT-E-UP65A/AW Manual de usuario
Motorized TV Stand with Remote Control
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-e-up65a
SKU: MOUNT-E-UP65A/AW
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please contact our product support team at 309-278-5303 or [email protected]om for further assistance.
Check carefully to make sure there are no missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
132 lbs
(60 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
3
PACKAGE CONTENTS
A (x1)
Motorized Li
E (x1)
TV Bracket
I (x1)
Adapter Cover
J (x1)
Power Cable
K (x1)
Remote
S-A (x16)
ST5.5x16mm
Screw
M-A (x4)
M6x14mm
Screw
M-B (x4)
M8x16mm
Screw
M-C (x4)
M6x30mm
Screw
M-D (x4)
M8x35mm
Screw
M-E (x4)
M8 Washer
M-F (x4)
Small Spacer
M-G (x4)
Large Spacer
T-A (x1)
4mm Allen
Wrench
T-B (x1)
6mm Allen
Wrench
T-C (x1)
17mm Wrench
S-B (x2)
ST4.2x20mm
Screw
S-C (x12)
M6x12mm
Screw
S-D (x4)
M10x20mm
Screw
S-E (x4)
M10 Nut
F (x2)
VESA Bracket
G (x1)
Control Unit
H (x1)
AC Adapter
B (x1)
Mounting
Plate
C (x2)
Shelf Support
D (x1)
Shelf
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
Phillips
Screwdriver
4
PRE-ASSEMBLY
When fabricating custom cabinetry for your motorized TV mount, ensure there will be at least 50mm
of clearance on the sides and front of the TV along with at least 10mm of clearance on the top.
Building or Selecting a Custom Cabinet
5
ASSEMBLY STEPS
Connect cable from Motorized Li (A) to Control Unit (G). Place AC Adapter Cover (I) over
AC Adapter (H). Connect Control Unit (G) cable and Power Cable (J) to AC Adapter (H).
STEP 1
G
I
J
H
A
6
STEP 2
Slide Mounting Plate (B) onto Motorized Li (A) and secure using M6x12mm Screws (S-C) and
4mm Allen Wrench (T-A) . Connect Shelf Supports (C) to the sides of Motorized Li (A) using
M6x12mm Screws (S-C) and 4mm Allen Wrench (T-A). Attach Shelf (D) to top of Shelf Supports
(C) using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-A).
T-A
T-A
T-A
C
D
C
S-C S-C
S-C
A
B
Attach Shelf (D) to top of Shelf Supports (C) using M6x12mm Screws (S-C) and 4mm Allen
Wrench (T-A).
7
STEP 3
Place the li assembly inside of your
custom cabinetry and plug into nearby
outlet.
Press the side button on Control Unit
(G) using a pencil or small tool. The
li will beep once, indicating the li
is ready to be paired with the Remote
(K).
Press the button on the remote.
Remote will beep for 10 seconds, and
then emit one final beep to indicate
successful paring. Press the arrow to
raise the li.
K
G
STEP 4
Secure li assembly to inside of cabinet by installing ST5.5x16mm Screws (S-A)
into the tabs on li using a drill. Secure Control Unit (G) and AC Adapter with
Cover (H, I) using ST4.2x20mm Screws (S-B) and ST5.5x16mm Screws (S-A) and
a drill.
S-A
S-A
I
H
G
S-B
8
STEP 5
Attach TV Bracket (E) to Mounting Plate (B) using M10x20mm Screws (S-D), M10 Nuts (S-E), 6mm
Allen Wrench (T-B), and 17mm Wrench (T-C).
Secure custom cabinet cutout to Shelf (D) using ST5.5x16mm Screws (S-A) and a drill.
E
T-B
S-E
T-C
S-D
B
S-A
D
9
STEP 6
STEP 7
Install VESA Brackets (F) to TV using appropriate Screws (M-A, M-B, M-C, M-D), M8 Washers (M-E),
Spacers (M-F, M-G) and a Phillips screwdriver.
Place TV with VESA Brackets (F) onto TV Bracket (E). Tighten set screw on VESA Brackets (F) with
Phillips screwdriver to secure.
NOTE:
For heavier TV’s, it is recommended to have a
second person assist with placing the TV.
F
E
F
10
STEP 8
Motorized li is now ready for use.
Tabla de contenidos
Otros manuales de Soporte de TV de Vivo
Vivo
Vivo MOUNT-VW04G Manual de usuario
Vivo
Vivo STAND-KIT-TV03E Manual de usuario
Vivo
Vivo MOUNT-VWSF1W Manual de usuario
Vivo
Vivo MOUNT-VW70F Manual de usuario
Vivo
Vivo STAND-TV00J Manual de usuario
Vivo
Vivo MOUNT-E-UP65A Manual de usuario
Vivo
Vivo MOUNT-VC55A Manual de usuario
Vivo
Vivo MOUNT VW01 Manual de usuario
Vivo
Vivo STAND-TV07 Manual de usuario
Vivo
Vivo MOUNT-CR01V Manual de usuario
Vivo
Vivo STAND TV00J Manual de usuario
Vivo
Vivo MOUNT-MM01B Manual de usuario
Vivo
Vivo STAND-TV02PW Manual de usuario
Vivo
Vivo MOUNT-SPSB3 Manual de usuario
Vivo
Vivo STAND-TV22S Manual de usuario
Vivo
Vivo MOUNT-WCB01 Manual de usuario
Vivo
Vivo STAND-TV07W Manual de usuario
Vivo
Vivo MOUNT-SF1BB Manual de usuario
Vivo
Vivo MOUNT-M-FD27 Manual de usuario
Vivo
Vivo MOUNT-VW080S Manual de usuario
