Vivo STAND-V200S Manual de usuario
Mechanical Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v200s
SKU: STAND-V200S
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x2)
Arm
B(x1)
Base
C(x1)
Clamp
D(x2)
Clamp Disk
E(x2)
M6x8
F (x1)
3mm Allen
Wrench
G(x1)
5mm Allen
Wrench
H (x1)
Support Plate
3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Desk Clamp Installation
Assemble base (B) to clamp (C) using M6x8 bolts (E), and tighten with 5mm Allen wrench (G). Unscrew
the large clamp bolts to the “open” position.
For 3/8” - 2” (10mm - 50mm) desk thickness, place clamp disks (D) onto the top of the clamp bolts.
Place assembled base onto edge of desk and tighten using the 5mm Allen wrench (G).
For 1-1/2” - 3-1/8” (40mm - 80mm) desk thickness, remove the two bolts from the back of the clamp
using the 5mm Allen wrench (G), and then reassemble clamp to the lower position. Place clamp disks
(D) onto the top of the clamp bolts. Place assembled base onto edge of desk and tighten using the
5mm Allen wrench (G).
OPTION B: Grommet Base Installation
Remove large clamp bolt from clamp (C). If necessary, drill holes in desk 55mm apart using a 3/8”
(10mm) drill bit. Secure base (B) to desk using clamp bolts with support plates (H), and tighten using
the 5mm Allen wrench (G).
NOTE: Grommet option will fit a desk thickness of 3/8” - 1-3/4” (10mm - 45mm).
WARNING!
PER ARM
4.4-15.4lbs
(2-7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
4
STEP 2
STEP 3
STEP 4
While holding the arms (A) in the closed position, cut the shipping tie from each arm.
1. Firmly hold the two halves of the spring arm together and have another person cut o the cable tie
from around the spring arm.
2. Slowly release the pressure on the spring arm and allow it to gradually stretch to its full extension.
Place the arms (A) onto the base (B). Tighten the
screw on the back of each arm using the 3mm Allen
wrench (F) or a flat blade screwdriver.
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes
of each monitor, making sure to leave 1/8” (3mm) of threads exposed.
5
STEP 5
STEP 6
Align bolts installed to monitors with VESA plate. Secure using
two more bolts (M-A or M-B) and washers (M-C) in the bottom
two holes. Tighten all four bolts with a Phillips screwdriver.
If the arms (A) are not able to maintain a lowered position, tighten bolts on the side of each arm using
the 5mm Allen wrench (G). Use cable clips on the arm to organize cables.
6
STEP 7
Tighten or loosen the tilt joint using the 5mm Allen wrench (G). Adjust the monitor positions as
desired.
7
LAST UPDATED: 10/22/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
Tabla de contenidos
Otros manuales de Rack y soporte de Vivo
Vivo
Vivo DESK-V000ME Manual de usuario
Vivo
Vivo STAND-V002 Manual de usuario
Vivo
Vivo STAND-V002D Manual de usuario
Vivo
Vivo STAND-V200L Manual de usuario
Vivo
Vivo life finds LF-VFS1A Manual de usuario
Vivo
Vivo STAND-V002LG Manual de usuario
Vivo
Vivo PP-1-T024D/G Manual de usuario
Vivo
Vivo STAND-LAP1F Manual de usuario
Vivo
Vivo STAND-LAP3 Manual de usuario
Vivo
Vivo DESK-EXT24/W Manual de usuario
Vivo
Vivo STAND-V003J Manual de usuario
Vivo
Vivo STAND V102C Manual de usuario
Vivo
Vivo MOUNT-PC01W Manual de usuario
Vivo
Vivo STAND-V032 Manual de usuario
Vivo
Vivo STAND-V003V Manual de usuario
Vivo
Vivo STAND-V002E Manual de usuario
Vivo
Vivo MOUNT-VP06B Manual de usuario
Vivo
Vivo MOUNT-KB05ES-D Manual de usuario
Vivo
Vivo STAND-TV65A Manual de usuario
Vivo
Vivo STAND-TV75R Manual de usuario
