Vivo STAND-V103F Manual de usuario

Triple Monitor Desk Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v103f

[email protected]om www.vivo-us.com 1-800-371-5654

SKU: STAND-V103F

PACKAGE CONTENTS

WARNING!

A (x1)

Pole

B(x1)

Weighted Base

C(x1)

Decorative

Cover

P1 (x2)

VESA Plate

(side)

M(x2)

Spare Plastic

Cover

O(x1)

Wrench

I (x2)

M8x10 Bolt

K (x12)

M4x30 Bolt

L (x12)

M4 Spacer

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

J(x12)

M4x12

Thumbscrew

D1 (x1)

Monitor Arm

(center)

D2 (x2)

Monitor Arm

E (x4)

Monitor Arm

Cover

F(x4)

Plastic Pad

G (x2)

M10x47 Bolt

H (x3)

M6x29 Bolt

N(x1)

Allen Wrench

Set

P2 (x1)

VESA Plate

(center)

Q1 (x2)

Security Nut

Q2 (x1)

M4x6 Bolt

R(x4)

Wire Clip

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD

OR BACKWARD.

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

ASSEMBLY STEPS

STEP 1

TOOLS NEEDED

Phillips

Screwdriver

Install the pole (A) to the weighted base (B) using M6x29 bolts (H).

Tighten with a Phillips screwdriver and install decorative cover (C).

22 lbs

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Assemble the monitor arms (D1, D2) by placing plastic pads (F) on the top and bottom of arms (D2)

and inserting them into the center arm (D1) as shown in the diagram. Secure with M10x47 Bolts (G)

and tighten with the large Allen wrench (N). Press monitor arm covers (E) onto the top and bottom of

arm joints.

STEP 3

Carefully slide assembled monitor arm down onto the

pole, making sure holes for wire clips are facing down, and

secure with M8x10 bolts (I) using the medium Allen wrench

(N). Attach the wire clips (R) to the monitor arm.

STEP 2

2.1

2.2

2.3

STEP 4

OPTION A: Flat Back Monitor

Attach the VESA plates (P1, P2) to the monitors

using M4x12 thumb bolts (J).

NOTE: Hand tighten screws to avoid stripping the

plastic screw heads.

OPTION B: Curved Back Monitor

Attach the VESA plates (P1, P2) to the monitors

using M4 spacers (L) and M4x30 bolts (K). Tighten

with a Phillips screwdriver.

STEP 5A

Slide the center monitor onto the head of monitor arm. Secure with the M4x6 bolt (Q2) and tighten

with a Phillips screwdriver.

d1,d2

STEP 6

Pry o the plastic cover and tighten the nut on the side of the tilt joint with the wrench (O) to fix the

tilt angle of side monitors. Tighten the grub screw on the back of center monitor joint using the small

Allen wrench (N) to fix tilt angle of center monitor.

STEP 5B

Slide the side monitors onto the heads of monitor arm and install the security nuts (Q1). Make sure

the security nuts are installed before you rotate the monitors.

grub

screw

Fix the tilt angle

d1,d2

STEP 7

STEP 8

Pry o the plastic cover and use the large Allen wrench (N) to adjust swivel joints if needed.

To adjust center monitor height, turn the screw behind center monitor joint using the medium Allen

wrench (N). To level the side monitors, remove the security nut and turn the bolt with the small Allen

wrench (N) to raise or lower the monitor. Replace nut aer the adjustment.

STEP 9

Manage cables using the wire clips (R). Remove the split cap from the pole and feed cables through,

pulling ends out from the opening in back. Replace the split cap when finished.

Last Updated: 09/09/2019

If any parts are received damaged or defective, please contact us. We are happy to

replace parts to ensure you have a fully functioning product.

For more VIVO products, check out our website at:

www.vivo-us.com.

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

[email protected]om www.vivo-us.com 1-800-371-5654

Tabla de contenidos

Otros manuales de Rack y soporte de Vivo

Vivo

Vivo MOUNT-PC06E Manual de usuario

Vivo

Vivo MOUNT-RAIL02W Manual de usuario

Vivo

Vivo STAND-BK01B Manual de usuario

Vivo

Vivo STAND-V102K Manual de usuario

Vivo

Vivo STAND-V002N Manual de usuario

Vivo

Vivo DESK-V000KL Manual de usuario

Vivo

Vivo DESK-V000VL Manual de usuario

Vivo

Vivo STAND-TDML1 Manual de usuario

Vivo

Vivo STAND-V012L Manual de usuario

Vivo

Vivo STAND-V101G2 Manual de usuario

Vivo

Vivo STAND-SIT1BW Manual de usuario

Vivo

Vivo STAND-V012C Manual de usuario

Vivo

Vivo STAND-V004P Manual de usuario

Vivo

Vivo STAND-V101A Manual de usuario

Vivo

Vivo MOUNT-VP07DP Manual de usuario

Vivo

Vivo STAND-SHELF60B Manual de usuario

Vivo

Vivo MOUNT-KAYAK1 Manual de usuario

Vivo

Vivo STAND-V101BDU Manual de usuario

Vivo

Vivo MOUNT-VP01W Manual de usuario

Vivo

Vivo DESK-EXT24/W Manual de usuario

Vivo

Vivo STAND-V102G2U Manual de usuario

Vivo

Vivo STAND-V103 Manual de usuario

Vivo

Vivo STAND-TV09 Manual de usuario

Vivo

Vivo STAND V004M Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario