Vitek VTC-IRH70 Manual de usuario

blackyellowmagentacyan

VITEK

VTC-IRH70/650

Long Range Weatherproof IR

Bullet Camera

• 1/3” Super HAD Color CCD

• High Resolution with 560 TV Lines Resolution in Color (600 TV Lines in B/W mode)

• 70 IR LEDs at 850nm enable viewing in Total Darkness up to 300 Feet

• Simultaneous Color and Black & White Focus Adjustment

• Infrared LED Dynamic Intensity Control with automatic brightness adjustment of IR LEDs

to help prevent washed out images when objects are too close

• Camera and IR LED compartments are separated using a dual glass design to prevent

stray IR light from entering the lens

• Vari-Focal 6~50mm DC Auto Iris IR Lens

• Virtual Wide Dynamic Range

• OSD control

• Secondary Video Output & OSD Control Joystick are accessible inside a gasket sealed

removable side panel

• Externally adjustable Focus & Zoom with clutch mechanism to eliminate over-tightening

• Gasket sealed external focus and zoom controls with clutch mechanism to eliminate

over-tightening for ease of installation and adjustment

• Heavy Duty IP68 rated Weather/Vandal Resistant Aluminum Construction is 100% water

and dust proof

• Fully adjustable 3 axis wire feed-through mount

• Dual Voltage: 12VDC / 24VAC

VTC-IRH70-650 



Table of contents

1. Safety Instructions and Notes.................................................................................. 2

2. General Descriptions ............................................................................................... 3

3. Supplied Items ......................................................................................................... 3

4. Part names .............................................................................................................. 4

5. Installation Instructions ............................................................................................ 5

5.1. Mounting The Camera......................................................................... 5

5.2. Power Supply Connections.................................................................. 5

5.3. Setup of Zoom and Focus ................................................................... 5

6. Setup Menu ............................................................................................................. 6

6.1 Main Menu........................................................................................... 6

6.2 Exposure Menu ................................................................................... 7

6.2.1 BLC Menu ........................................................................................... 8

6.2.2 HSBLC Menu ...................................................................................... 9

6.2.3 D-WDR Menu ..................................................................................... 10

6.3 Day Night Menu.................................................................................. 10

6.3.1 Day Night Auto Menu ......................................................................... 10

6.4 3-DNR Menu ...................................................................................... 12

6.5 Picture Menu ...................................................................................... 13

6.6 Special Menu...................................................................................... 14

6.6.1 Camera Title Menu ............................................................................. 15

6.6.2 Motion Menu....................................................................................... 16

6.6.3 Privacy Menu...................................................................................... 17

6.7. Lens Menu.......................................................................................... 18

6.7.1 Focus Adjust Menu............................................................................. 18

7. Specifications.......................................................................................................... 19

8. Dimensional Drawings ............................................................................................ 20

9. Warranty ................................................................................................................. 21



          VTC-IRH70-650



The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of

un-insulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock.

Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his/her own expense.

Caution -- Any changes or modifications in construction of this device which are not expressly approved by

the party responsible for compliance could void the user's authority to operate the equipment.

1. Safety Instructions and Notes



• Please read these safety and operating instructions before placing the camera into

operation.

• Keep the manual in a safe place for later reference.

• Pay attention to safety when laying the connection cable and observe that the

cable is not subjected to

heavy loads, kinks, damage or moisture.

• Never open the device to expose boards or lens.

The warranty becomes void if repairs are undertaken by unauthorized persons.

• Maintenance and repair must be carried out only by authorized service centers.

• Use only a mild detergent to clean the housing.

• Keep the window surface clean from dirt or dust, which may reflect the infrared

light into the lens at night..

•The camera should never be operated in an environment that exceeds the technical specifications as this

may result in the destruction of the product and will also void the factory warranty.



WARNING

Caution

To prevent electric shock

and risk of fire hazards, do

NOT use other than

specified power source.



VTC-IRH70-650 



2. General Descriptions

Main Features

· Fully external adjustment controls for lens, OSD or Dip switch settings

· 1/3" Super HAD II CCD

· High Resolution 560TVL (Color), 600TVL (B/W)

· 3-DNR (3 Dimensional Digital Noise Reduction)

· Extended Dynamic Range by the use of D-WDR technology

· Sensitivity: COLOR: 0.35Lux (@50IRE, F1.2), B/W: 0.04Lux (@50IRE, F1.2),

SENSE-UP(x4): 0.0035Lux (@50IRE, F1.2), 0 Lux with built-in 70 Infrared LEDs on

· Cable feed-through wall bracket (Concealed Wiring Bracket)

· 6~50mm Variable Focal Length Lens

· Weatherproof (IP68) Optimized for Outdoor Use

. OSD (On Screen Display) Function Control

. Sense-up (~ x128)

. AWB, Flickerless, Digital Zoom, BLC and HSBLC

. Motion Detection (4 Zone), Privacy Zone (8 zones), Flip Function

· 24VAC / 12VDC Dual Power

· Secondary Video output for simple installation & maintenance

· Easy adjustment for zoom, focus and OSD controls

· 70x Self Adjusting IR LEDs

· 300' Night observation range

Contains Sony Super HAD II CCD image sensor,

· Provides a brighter image and true color reproduction while extending the

viewing range in low lux (light) conditions with double the sensitivity of other

sensors.

Extensive DAY-NIGHT capabilities,

- True (ICR) DAY-NIGHT Function

- No compromising image color under low color temperature (incandescent light).

- Features 70 Infrared LEDs affording clear images up to 300’ where no

illumination is available.

With 24VAC/12VDC dual power design,

- Offering flexibility during installation and reduces risk of damage due to voltage

3. Supplied Items

• 1x VTC-IR70650 3-DNR Weatherproof IR Bullet Camera

• 1x ⓓSunshield with ⓐattachment thumb screw

• 1x 3mm Hex L-wrench

• 1x 5mm Hex L-wrench

• 4x Wall mounting screws with anchors

• 1x Installation and Operating manual

• 1x Mounting template

• 1x Video Sub-output cable

• 1x Mounting plate adaptor for easy installation

          VTC-IRH70-650



4. Part Names



4.1Front view



4.2Rear side view



ⓔ

ⓕ

ⓒ

ⓓ

ⓐ

ⓑ

①Focus adjustment

②Zoom adjustment



①

②

ⓖ

ⓐSunshield attachment thumb screw

ⓑIR LED Panel

ⓒDouble Glass Window

ⓓSunshield

ⓔOn Screen Display control cover

ⓕWall Mounting Bracket

ⓖMounting Plate Adaptor



  

VTC-IRH70-650 



5. Installation Instructions

•Makesurethepowerisnot applied before installation.

•Once the camera is installed you may first connect the low voltage (DC12V or AC24V) wire to the

camera power connector, then plug the AC adapter to AC outlets to avoid an improper reset from power

jitter and possible damage from voltage surge.

5.1. Mounting the camera on a wall

1) Make the drill holes with using the supplied

template.

2) Insert the anchors into the drilled holes

3) Match the mounting plate to the drilled position

4) Fix the mounting plate by using the supplied

screws

5) Slide the Mounting Bracket into place

6) Fix the Mount to the Plate using supplied

screws

5.2. Power Supply Connections

Camera can work with either 24AC or 12VDC, dual voltage power.

It is strongly required the polarity-matched connection for 12VDC supply,

otherwise IR LEDs will not operate at night.

Primary and secondary grounds are completely isolated to avoid the possibility of

ground-loop problems.



5.3. Setup of the Zoom and FOCUS

1) Power up the camera and connect a monitor.

2) Enter LENS>DC>FOCUS ADJUST in MENU

3) Set ②Zoom adjustment first, then adjust①Focus adjustment. The lens

adjustment is completed.

4) Exit MENU.



Clamp connectors of power

input

AC24V/DC12V (RED WIRE)

AC24V/GND (BLACK WIRE)



          VTC-IRH70-650



6. SETUP Menu

The Setup menu can be accessed and controlled by OSD control joy stick on the

side of camera.

Five commands are available with the use of the joy stick.

In the menu, use ▲,▼ to move menu, ◀,▶ to change the settings and press ●to

select or enter.

FACTORY DEFAULT in this manual may NOT be identical to the default values

set by the FACTORY due to feature improvements or custom requirements.

6.1 MAIN menu - To enter menu, press ●when MENU is not active..

MAIN

Factory

Default

Descriptions

EXPOSURE

Sets SHUTTER, AGC, SENSE-UP, BLC and D-WDR.

DAY/NIGHT

AUTO

Sets DAY / NIGHT to AUTO, NIGHT and DAY.

AUTO – Camera switches DAY from/to NIGHT automatically. DELAY,

D-->N LEVEL, N-->D LEVEL and NIGHT MODE can be set in the menu.

NIGHT – Forced to remove IR cut filter and switch to B/W.

DAY – DAY/NIGHT is disabled and outputs color video..

3DNR

Sets 3DNR (Digital Noise Reduction) LEVEL.

PICTURE

sets SHARPNESS, BLUE, RED, GAMMA and WHITE BALANCE.

SPECIAL

Sets CAM TITLE, D-EFFECT, MOTION, PRIVACY, SYNC, LANGUAGE and

OSD (On Screen Display) COLOR.

LENS

Selects DC (Auto Iris) or MANUAL lens.

BRIGHTNESS for both lenses can be set in the menu.

Provides FOCUS ADJ. Mode for both Day (Color) and

Night (B/W) With Adjustable Time intervals for best image

sharpness in all conditions.

FACTORY SET

Restores and saves FACTORY DEFAULTS.

EXIT

Save and Exit.



Joy

stick



VIDEO

SUB-OUT

connector

SYMBOL descriptions for joystick

operation;



-▲,▼,◀,▶denotes the directions

of Joystick lever operation.

-● denotes Pressing straight

down of Joystick lever



VTC-IRH70-650 



6.2 EXPOSURE menu

To enter EXPOSURE menu, press ●at MAIN>EXPOSURE.

EXPOSURE

Factory

Default

Descriptions

1/60

(1/50)

1) If LENS at MAIN menu was set to DC, a fixed shutter is selectable

from 1/60(NTSC) or 1/50(PAL), FLK, 1/250, 1/500, 1/2000, 1/5000,

1/10000, 1/100000 and a fixed sense-up rate is selectable from

x256, x128, x64, x32, x16, x8, x4, x2.

At x2~x256, DSS(Digital Slow Shutter) is operating with the selected

frame integration rates regardless of the light level.

When TV system is NTSC(PAL) and Main power is 50Hz(60Hz),

set to FLK(Flickerless mode).

FLK makes the sensitivity lower about 30% at low light.

DC lens must be used for these settings to get a proper video

level.

SHUTTER

AUTO

2) If LENS at MAIN menu was set to MANUAL, SHUTTER should be

set to AUTO to get a proper video level with the automatic shutter

range between 1/60(1/50)~1/100,000sec.

Color rolling or Video level hunting under Fluorescent or similar

lighting may occur in this configuration.

---

1) If DAY / NIGHT at MAIN menu was set to AUTO or NIGHT,

AGC is not user adjustable.

AGC

MIDDLE

2) AGC can be set to MIDDLE, HIGH, OFF or LOW.

Settings are not available if DAY /NIGHT at MAIN menu is set to

AUTO

SENSE-UP

OFF

AUTO

SENSE-UP is available only when SHUTTER is 1/60(1/50) or AUTO.

If set to AUTO, max. integration rate for DSS can be set to x2, x4, x8,

x16,

x32, x64, x128 or x256..

The integration frames vary automatically within the max. rate

according to

the light level when light becomes low and DSS is operating.

The higher sense-up rate, the higher sensitivity but the slower refresh

rate.

Some white dots may appear by sense-up due to CCD’s long

accumulation

caused by a long shutter period.

BLC

OFF

OFF, BLC and HSBLC are available.

See BLC & HSBLC menus at 6.2.1 & 6.2.2 for detail.

D-WDR

OFF

COMP. and HIGH SUP. can be set.

See D-WDR menu at 6.2.3 for details



          VTC-IRH70-650



6.2.1 BLC menu

To enter BLC menu, press ●at EXPOSURE > BLC > BLC.

BLC

Factory

Default

Descriptions

GAIN

LOW

Sets the compensation gain to LOW, MIDDLE or HIGH.

For best compensation results, adjust window for size

and location as well as GAIN.

Back Light Compensation (BLC) may not be precise if

the background is varying continuously between bright

and dark.

DEFAULT

Loads the default for BLC settings.

HOR.

MOVE

◀moves BLC window leftward and ▶moves it rightward

WIDTH

◀decreases and ▶increases WIDTH of BLC window

from the right.

VER. MOVE

◀moves BLC window upward and ▶moves it

downward.

HEIGHT

◀decreases and ▶increases HEIGHT of BLC window

from the bottom.



BLC OFF

BLC ON



VTC-IRH70-650 



6.2.2 HSBLC menu - High Light Masking

To enter HSBLC (High Sensitivity BLC) menu, press ●button at EXPOSURE >

BLC > HSBLC.

HSBLC cuts out the highlighted video and processes that area as black masked.

The cut out video is excluded in measuring light level by the signal processor.

BLC

Factory

Default

Descriptions

LEVEL

Sets the threshold for highlight cut out between 0~8.

Lower setting is more sensitive and starts cutting out

from lower level

of highlight. The cut out area is masked by black color.

DEFAULT

Loads the default for HSBLC settings.

HOR.

MOVE

◀moves BLC window leftward and ▶moves it rightward.

WIDTH

◀decreases and ▶increases WIDTH of BLC window

from the right.

VER. MOVE

◀moves BLC window upward and ▶moves it downward.

HEIGHT

◀decreases and ▶increases HEIGHT of BLC from the

bottom.



HSBLC OFF

HSBLC ON



Otros manuales para VTC-IRH70

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vitek

Vitek

Vitek VTD-A2812/I Manual de usuario

Vitek

Vitek Transcendent VTC-TNB5RME Manual de usuario

Vitek

Vitek VT-TPTZ10HR-2A4 Manual de usuario

Vitek

Vitek VT-PTZ12W Manual de usuario

Vitek

Vitek VTC-TNT30R3F Manual de usuario

Vitek

Vitek VTD-THD5R3 Manual de usuario

Vitek

Vitek TRANSCENDENT VTC-TNB4LPRN Manual de usuario

Vitek

Vitek VTD-HOCR2812/V Manual de usuario

Vitek

Vitek VTC-EB25C Manual de usuario

Vitek

Vitek VTC-EB15B Manual de usuario

Vitek

Vitek VTC-C770/WDR Manual de usuario

Vitek

Vitek VTD-T4DIR2VD Manual de usuario

Vitek

Vitek VTC-IRLED24H Manual de usuario

Vitek

Vitek VTD-VH49VP4 Manual de usuario

Vitek

Vitek VTC-C01 Manual de usuario

Vitek

Vitek VTC-B74 Manual de usuario

Vitek

Vitek VTC-TTAT2HR2F Manual de usuario

Vitek

Vitek Transcendent Series Manual de usuario

Vitek

Vitek VTD-AR2D4FN Manual de usuario

Vitek

Vitek VTC-IRX36/3895 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Vitek

Vitek VTC-IRHCM1 Manual de usuario

Vitek

Vitek Transcendent VTD-THMD2RF Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario