Visonic PowerMax Plus Manual de usuario

1

Quick Start Guide for the PowerMax Plus

Thank you for choosing the Visonic PowerMax Plus security system. Please follow these instructions

to ensure your system is setup properly.

1. Locate your PowerMax unit within 6 feet of a power plug and a phone jack.

2. Open the PowerMax battery door with a philips screw driver, as shown in the diagram below.

3. Once you have opened the Unit, plug the battery in as shown below and close the door,

screwing the retaining screw in tight.

4. Now, remove the retaining screw from the back bracket of the PowerMax Plus unit, once the

screw is removed, remove the cover plate. You will now need to connect the AC power supply

transformer. Strip away ¼ inch of the wire insulation, exposing copper on either end of the

wire. Connect one end to the transformer terminals, and the other end to the Panel AC terminals

in the upper right hand corner shown below. This is AC power, so no polarity is observed.

5. If mounting the PowerMax Plus to the wall, you will need to mount the back cover to the wall

first before re-connecting it to the Powermax unit. When doing so, remember to replace the

retaining screw and screw it tight.

2

Now that your panel is mounted and powered up, you are ready to learn in your sensors.

First you will need to get into Installer mode on your panel.

1. The first display will be Not Ready or Ready, press the Next key until the display reads

Installer Mode, when it does, press Show/OK. You will now be prompted to enter the Installer

Code, which is 9999 by default; press Show/OK when done.

2. When you see New Instl Code, press Next and you will see Enrolling. Press Show/OK to

select.

3. When you see Enrolling Type, press Next and you will see Enroll WL Device. Press Show/OK

to select, then press Show/OK repeatedly till you see Zone --. Press Next once to select the

zone 1.

4. Press Show/OK to accept, and it will display Transmit Now. You will now need to transmit a

signal from the device you are enrolling.

5. If it is a door sensor, open and close the sensor, or if a motion detector wave your hand in front

of it. At this point your panel should beep several times and you should see a black box next the

the word Zone 1.

6. Press Next to select the next zone and repeat steps 4 and 5 for the enrollment of the next device.

7. If enrolling a Keychain remote, follow the above steps up to step 3; and instead of selecting

Enroll WL Device, press next one more time to select Enroll Keyfob, when prompted to

transmit now simply hold down any one of the buttons on the keychain remote till the system

beeps.

8. At any point in programming you can back up a step by pressing the HOME button; when you

are done enrolling your devices, you can press the HOME key repeatedly to exit out of

programming, pressing the Show/OK button when prompted.

Now, you can define your desired zones

3

You are now ready the mount your sensors and get your system operational.

This Diagram shows how door and window

sensors are to be mounted. Note that you

should have the magnet and transmitter less

than ½ inch apart. The magnet is omni-

directional, use this to your advantage when

choosing a location for it.

This Diagram shows how Motion Detectors

are to be mounted. Select a location on your

wall that will have the ideal line of sight.

Corner mounting is optimal. Note that motion

detectors need to be mounted a minimal of 6-8

feet high. Be sure to keep these away from any

heating and cooling vents.

If you have a Smoke Detector, you will need to mount it centrally in a room on the ceiling. Mount it

away from anything that could produce smoke or heat in a natural occurrence (i.e. kitchen, living room

with a fireplace, etc.)

Your system should be ready to use now. Test your door sensors by activating the door Chime (press

and hold the 8 Key till it beeps). When arming and disarming your system, you will need to use the

Default Master Code which is 1111. Thank you for choosing the Powermax Plus to secure your home.

If you have any questions please call Safemart at 800-628-6093.

Tabla de contenidos

Otros manuales de Sistema de seguridad de Visonic

Visonic

Visonic MCS-710 Manual de usuario

Visonic

Visonic PowerG SR-740 PG2 Manual de usuario

Visonic

Visonic PowerMaster-10 G2 Manual de usuario

Visonic

Visonic GB-501 PG2 Manual de usuario

Visonic

Visonic MC-302 PG2 Manual de usuario

Visonic

Visonic POWERMASTER-10 Manual de usuario

Visonic

Visonic SR-720 PG2 Manual de usuario

Visonic

Visonic IR-50 Manual de usuario

Visonic

Visonic PowerMax Complete Manual de usuario

Visonic

Visonic POWERMAX PRO Manual de usuario

Visonic

Visonic POWERMAX - Manual de usuario

Visonic

Visonic MCT-211 Manual de usuario

Visonic

Visonic MCS-730 Manual de usuario

Visonic

Visonic MAESTRO-1600 Manual de usuario

Visonic

Visonic MC-302 PG2 Manual de usuario

Visonic

Visonic POWERMAX - Manual de usuario

Visonic

Visonic AXS-10 Manual de usuario

Visonic

Visonic PowerMax10 Manual de usuario

Visonic

Visonic POWERMAX - Manual de usuario

Visonic

Visonic POWERMAX - Instrucciones de funcionamiento

Visonic

Visonic POWERMASTER-10 Instrucciones de montaje

Visonic

Visonic KF-234 PG2 - Manual de usuario

Visonic

Visonic DL-125C Manual de usuario

Visonic

Visonic PowerMax10-G2 Instrucciones de montaje

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario