ViseeO MB-4 Manual de usuario
User Manual
Preface
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without the express
written consent of the manufacturer, Jan 2012.
Trademarks
Other product names mentioned herein are used for identification purpose only
and may be trademarks and/or registered trademarks of their respective
companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this manual,
the manufacturer and distributor assume no liability resulting from errors or
omissions in this manual, or from the use of the information contained herein.
2
Foreword & Important Note on Safety!! (MUST READ)
Please read this note before you install and use MB-4 Bluetooth Upgrade Adaptor!
Congratulation on your MB-4!
ViseeO MB-4 is the latest and one of the simplest Bluetooth Handsfree System
ever designed for your Mercedes Benz. You will be able to connect the latest
mobile phones to the handsfree system, sync phonebook and dial/answer a call
from vehicle's original steering wheel control or headunit keypads. Moreover, it has
an USB charging port which allows you to recharge the battery of your mobile
phone or electronic gadget. Although ViseeO MB-4 is very easy to install and
operate it is still recommended that you read all chapters in this manual before
using the adaptor.
Road Safety
We strongly advise that full attention is to be paid to the traffic conditions whenever
the vehicle is moving. Distraction of attention can lead to dangerous traffic situation.
Even when using a handsfree car kit driver is always advised to avoid phone call
during a difficult and complex traffic situation.
Use Only Approved Replacement Parts
Please always use official parts for your ViseeO unit as unknown spare or
replacement parts may lead to malfunction.
3
QUICK START GUIDE
CAUTION!! DO NOT ATTEMPT TO INSTALL THE UNIT WHILE THE CAR IS IN MOTION!
INSTALLING MB-4
(For detailed instruction please see Section 2.1 Installing the Main Unit)
1. Make sure the engine is off.
2. Locate your UHI/MHI connector (It is usually
situated in the tray under the front armrest).
3. Make sure there is no cradle attached to the
UHI/MHI connector.
4. Press and hold MB-4 UHI release button then,
gently slides MB-4 onto the UHI/MHI connector until in
lock into the connector.
5. Turn on the engine and make sure MB-4’s OLED
screen and green LED is on.
* If you have a NTG 4 you will need to set the dip switch 1 & 2 to off position before installing the unit (For further
information please see Section 1.5 Software Dip Switch and NTG 4 Vehicles)
CONNECTING MB-4 TO YOUR MOBILE PHONE FOR THE 1
ST
TIME
(For detailed instruction please see Section 3.1 Pairing for the First Time)
1. Press [PAIR] on MB-4 in the standby mode.
(If you do not see the PAIR function in the main screen
please refer to the manual Section 3.1 Pairing for the First Time for further information)
2. MB-4 should display “PAIRING NOW... Search ViseeO on your phone”.
6. Enable Bluetooth on your phone and search for a new Bluetooth device.
7. Select MB-4 when displayed a list of available Bluetooth devices nearby.
8. Enter 1234 on your mobile phone when the pass-code is requested.
(If you have a Samsung
Galaxy phone please refer to manual instruction Section 6.5 PIN Selection for further information)
9. The signal sign on your vehicle's screen should become solid when the connection is
successful.
Signal sign on a Comand APS Screen
No Phone Device
SYNC MENU PAIR
<<
VISEEO1
Telephone Number
TEL
Calls
Redial
Delete
PAIRING NOW…
Search ViseeO
on your phone..
4
MAKING A CALL
(For detailed instruction please see Section 3.4 Making the First Call)
1. Connect your phone with MB-4.
2. Dial a set of numbers you wish to call using the numeric keypad on your Comand console.
3. Press the answer button on your Comand console to make a phone call.
4. To end the call, press the hang up button on your Comand console to end the call.
SYNC FOR THE 1
ST
TIME
(For detailed instruction please see Section 4.1 Sync Phonebook)
1. Connect your phone with MB-4.
2. MB-4 should automatically sync with your phone as soon as they are connected.
3. During the uploading you will see the symbol > appearing on the top right of the MB-4’s OLED
panel.
4. When the symbol > disappears MB-4 will transfer the phonebook to your Comand console.
MB-4 will temporary disconnect from your Comand console.
5. After the connection comes back wait for a while for Comand console to organize the
phonebooks.
(If you have large phonebook such as 500 entries or even more it will take some time for
Comand console to organize your phonebook).
6. Press TEL button on the Comand console to access telephone function.
7. Press Phonebook button on the Comand console to access your phonebook.
<< >
HTC 7 MOZART
Connected
SYNC MENU P2
This symbol indicate that
MB-4 is now uploading
phoneboo form your
phone memory
This symbol indicate
that Automatic Sync is
on
5
Preface................................................................................................................................. 1
Foreword & Important Note on Safety!! (MUST READ) .................................................................... 2
QUICK START GUIDE .............................................................................................................. 3
1. Understanding Your MB-4 ..................................................................................................... 6
1.1 Package Contents ........................................................................................................ 6
1.2 MB-4 Main Unit & Descriptions ........................................................................................ 7
1.3 MB-4 OLED Display & Main Screen Icon Descriptions........................................................... 7
1.4 MB-4 Keypads and Functions.......................................................................................... 8
1.5 Software Dip Switch and NTG 4 Vehicles (W204, W212, W207, etc.) ......................................... 8
2. Installation ....................................................................................................................... 10
2.1 Installing the Main Unit ................................................................................................ 10
3. Basic Operation ................................................................................................................ 11
3.1 Pairing for the First Time.............................................................................................. 11
3.2 Pairing with Multiple Phones......................................................................................... 12
3.3 Using the Quick Switch for Paired Phones ....................................................................... 12
3.4 Making the First Call ................................................................................................... 13
4. Phonebook Function .......................................................................................................... 14
4.1 Sync Phonebook ........................................................................................................ 14
4.2 Manually Upload Phonebook......................................................................................... 15
4.3 Phonebook Organization for NTG 4 Vehicles .................................................................... 16
4.4 Phonebook Setting ..................................................................................................... 17
4.5 SYNC Now Command and SYNC in Progress Sign............................................................. 18
5. Advanced Bluetooth Setting ................................................................................................ 19
5.1 Disconnect from the Current Connected Device ................................................................ 19
5.2 Reconnect a Paired Device ........................................................................................... 19
5.3 Remove a Paired Device .............................................................................................. 20
6. Other Advanced Settings .................................................................................................... 21
6.1 Microphone Volume Setting.......................................................................................... 21
6.2 Language Setting ....................................................................................................... 21
6.3 Factory Default Setting (Master Reset) ............................................................................ 21
6.4 Firmware Update and Version Check .............................................................................. 22
6.5 PIN Selection............................................................................................................. 23
6.6 Using the Charging Function ........................................................................................ 24
7. Miscellaneous................................................................................................................... 25
7.1 Trademark ................................................................................................................ 25
7.2 Product Information .................................................................................................... 25
6
1. Understanding Your MB-4
1.1 Package Contents
1. MB-4 main unit.
2. USB to mini USB cable.
3. ViseeO Software Upgrade Cable.
7
1.2 MB-4 Main Unit & Descriptions
5V Mini USB Charging Port
Quick Switch for Paired Phones/Menu
Browsing Button
SYNC now/
Return/Cancel Button
Menu/Confirm Button
Power Indicator
OLED Display
UHI Release Button
CPU Software Upgrade Port
Software Dip Switch UHI Compatible Socket
1.3 MB-4 OLED Display & Main Screen Icon Descriptions
HTC 7 MOZART
Connected
SYNC MENU P2
Auto SYNC Status Phone Device Name
Left Button Function
Middle Button Function
Right Button Function
<<
Connection Status
>
Phonebook Upload
Status
8
1.4 MB-4 Keypads and Functions
Each key corresponds to a designated command shown on the display
Left Key SYNC Now, Return to Upper Level Menu, Cancel,
Mic Volume Down
Middle Key Main Menu, Confirm, Save, Setup, OK, Delete
Right key Switch to Next Paired Phone, Browse Next Menu
Item, Yes, Mic Volume Up
1.5 Software Dip Switch and NTG 4 Vehicles (W204, W212, W207, etc.)
Different years of Mercedes Benz vehicles are equipped with different types of the
UHI interface system. MB-4 is designed to work with different type of Comand
systems via the software dip switch at the back of the unit.
<<
HTC 7 MOZART
Connected
SYNC MENU P2
9
Original
s
oftware
switch position for
Non-NTG4 vehicles
Software
s
witch
position for W204,
W212, W207 and
other NTG 4 vehicles
The factory default setting has the both dip switches 1 & 2 at the “ON” position (see
the illustration below) and this software setting is designed to work with Audio
20/Audio 50/COMAND APS NTG1 and NTG2 types of head units
Newer vehicles such as W204, W212, some of the GLK and W207 Coupe which
comes with a newer type of UHI/MHI Comand system (NTG 4) that requires
different type of software to work with. Therefore, before inserting MB-4 into the
NTG 4 Comand system you will need to switch to the right software before MB-4
can work without any problem. To switch to the NTG 4 software:
1. Remove the rubber from the software switch at the back of MB-4.
2. Switch both software switches 1 & 2 to the off position (see the illustration
below)
Now you are ready to insert MB-4 into the UHI connector of a NTG 4 vehicle.
10
Original phone
cradle and UHI
connector
2. Installation
2.1 Installing the Main Unit
ViseeO MB-4 is designed to work with a pre-installed UHI/MHI Comand system in
your vehicle. Therefore, you will need to locate the UHI/MHI connector which is
normally found in the tray under the front armrest.
If there is a phone cradle attached to the UHI/MHI connector, please
remove it first.
To remove the cradle:
1. Please make sure the vehicle engine is off.
2. Press the release button on your cradle (normally located at the top).
3. Remove the cradle from UHI/MHI connector with care.
Now install your MB-4:
1. Make sure there is no cradle attached to the UHI/MHI connector.
2. Press and hold the UHI release
button on your MB-4 then, gently slides
the MB-4 (UHI compatible socket side
facing downwards) onto the UHI/MHI
connector until it locks into the
connector.
3. Turn on the engine. MB-4's OLED
screen and the green LED should be
on to indicate the installation
successful.
UHI Connector
Press & hold the UHI Release Button
Tabla de contenidos
Otros manuales de Accesorios para automóviles de ViseeO
