Vip-Vision VDIRME Series Manual de usuario
VDIRME Series
Camera Quick Install Guide
Version 290517
Available in Low Light 2.0MP, 4.0MP and 8.0MP variants
Applicable Models
VSIP2MPVDIRME 2.0MP Professional Ultra Low Light Motorised Dome
VSIP4MPVDIRME 4.0MP Professional Motorised Dome
VSIP8MPVDIRM 8.0MP Professional Motorised Dome
Thank you for purchasing a VDIRME Series CCTV Surveillance Camera.
This Quick Install Guide covers basic setup, installation and use of your surveillance system.
For the full user manual, instructional videos, tips on using your surveillance system &
warranty information, please visit: www.vip-vision.com
2Crucial evidence. Always.
VDIRME Series | Surveillance Cameras
2Crucial evidence. Always.
Important Safeguards and Warnings
Electrical safety
• All installation and operation here should conform to your local electrical safety codes.
• Check if the power supply is correct before operating the device.
• The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated DC
12V or AC 24V in the IEC60950-1. (Power supply requirement is subject to the device label).
• Install easy-to-use device for power off before installing wiring, which is for emergent power off when necessary.
• Prevent the line cord from being trampled or pressed, especially the plug, power socket and the junction.
• Note: Do not connect these two power supplying sources to the device at the same time; it may result in device damage!
• We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
• We are not liable for any problems caused by unauthorized modification or attempted repair.
Environment
• Don’t aim device at strong light (such as lighting, sunlight and so on) to focus; otherwise it may cause overexposure (It is not
the device malfunction), which will affect the longevity of CCD or CMOS.
• Transport, use and store the device within the range of allowed humidity and temperature.
• Don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and with strWong electromagnetic
radiation or unstable lighting.
• Do not allow water and other liquid falling into the camera in case that the internal components are damaged.
• Do not allow rain or damp to the indoor device in case fire or lightning may occur.
• Keep the sound ventilation in case of heat accumulation.
• Pack the device with standard factory packaging or material with same quality when transporting the device.
• Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
Warning
• Modify the default password after login in order to avoid being stolen.
• Use the standard accessories provided by manufacturer and make sure the device is installed and fixed by professional
engineers.
• Prevent the device surface from the radiation of laser beam when using laser beam device.
• Do not provide two or more power supply modes for the device, otherwise it may cause damage to the device.
Statement
• Refer to the actual product for more details; the manual is just for reference.
• The manual will be regularly upgraded according to the product update; the upgraded content will be added in the manual
without prior announcement.
• Contact the supplier or customer service if there is any problem occurred when using the device.
• Contact the customer service for the latest procedure and supplementary documentation.
• There may be deviation between the actual value of some data and the value provided in the manual due to the reasons
such as the real environment is not stable and so on. Refer to the company’s final explanation if there is any doubt or dispute.
• The company is not liable for any loss caused by the operation which is not followed by the manual.
3
www.vip-vision.com
VDIRME Series | Surveillance Cameras
Operation and Daily Maintenance
• Do not touch the heat dissipation component of the device directly in order to avoid scald.
• Do not dismantle the device; there is no component which can be fixed by users themselves in the machine. It may cause
water leakage or bad image for the device due to unprofessional dismantling. Please contact after-sale service to replace
desiccant if it becomes green.
• It is recommended to use the device with thunder proof device in order to improve thunder proof effect.
• The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
• Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust or dirt on the lens surface.
Please use a dry cloth wet by alcohol to wipe away the dust gently if it is necessary to clean.
• Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent
first and then use it to clean the device. Finally use the dry cloth to clean the device. Don’t use volatile solvent like alcohol,
benzene, thinner and etc or strong detergent with abrasiveness, otherwise it will damage the surface coating or reduce the
working performance of the device.
• Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use, please refer to
the following methods to deal with once dirt is found:
• Stained with dirt
• Use oil-free soft brush or hair dries to remove it gently.
• Stained with grease or fingerprint
• Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or paper soaked with alcohol
or detergent to wipe from the lens center to outward. It is ok to change the cloth and wipe several times if it is not clean
enough.
FCC Information
1. FCC conditions
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference;
• This device must accept any interference received, including interference that may cause undesired operation.
2. FCC compliance
• This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Refer to the disk for more details, check and download corresponding user’s manual and tool. Before installation,
please open the package and check all the components are included. Contact your local retailer ASAP if something is broken
in your package
4Crucial evidence. Always.
VDIRME Series | Surveillance Cameras
Dimensions
1 x VDIRM Series IP Camera
1 x Quick Start Guide
1 x
Installation Accessories Bag:
• Position installation map
• Expansion bolts
• Installation screws
• Screwdriver
1 x CD
Included Components
Pre-install Information
Device framework
Component Name
1 Photosensor
2 IR light
3 Lens
4 Dome Enclosure
5 Dome Pedestal
6 12VDC input
7 Ethernet port
5
www.vip-vision.com
VDIRME Series | Surveillance Cameras
1. Installing the camera
1. Take out the installation map found in the accessories bag, paste it on your ceiling or wall and dig holes on the
installation surface according to the installation position map.
2. Take out three expansion bolts found in the accessories bag, and insert them into the holes you just made.
3. Use the wrench to loosen the locking screws, then pull the enclosure downward to separate.
4. Install the microSD card (1.2).
5. Run the wire through the bottom or side, and insert the multi-function cable into the exit hole on the installation
surface (1.3).
6. Adjust pedestal position, aiming it at the bottom hole. Take out three self-tapping screws found in the accessories
bag, and insert them into the expansion bolt bottom hole, fixing the pedestal to the surface.
7. Install the enclosure back to the pedestal by pushing upward and lock the screws firmly with a wrench.
8. Apply waterproofing to network cable (1.4) and then plug in all necessary ports (shown in pre-install).
9. Your setup is complete!
1.1 Follow the guidelines to install your camera (See image above)
Here will we walk through the installation process for your ‘‘VDIRME Series’’ camera. We will show you how to set-
up your equipment, how to adjust it, all of its components and how to get it up and running. Be sure to check the
pre-install to have an understanding of the included components, dimensions, and connection ports.
6Crucial evidence. Always.
VDIRME Series | Surveillance Cameras
1.2 Accessing the microSD card slot (optional)
1.2.2 Advantages of the microSD
1.2.1 Installing the microSD card
The microSD card is a very useful tool for anyone who wishes to have another way to back up storage, or is on a
budget and doesn’t have a recorder. The microSD card is placed inside of the camera, and can hold a set amount of
storage (dependent on size of card) for any intended use, such as: video playback, storage, backup etc.
The microSD card utilises “Edge Recording”. This is when the camera records video directly onto the installed card in
the camera, instead of a separate NVR or storage device. This gives the user more flexibility in recording video.
1. Use the screwdriver in accessories bag to loosen the four screws on the dome pedestal, then take down the
compression cover and take out the dome body.
2. Use the screwdriver to loosen three screws on the dome body and open it.
3. Locate the microSD card slot (Fig 1.2.1) and adjust the direction of the microSD card until installed properly.
4. Insert the microSD card into the installation slot.
5. Assure you install the device seal ring back to the dome body after installing the microSD card.
6. Use the screwdriver to tighten the three screws on the dome body and put the dome body back into its enclosure.
7. Use the screwdriver to tighten the back four screws on the dome body bottom and install the compression cover.
Note: Having a standalone microSD card will not assure that you have the same quality playback, nor the capacity com-
pared to a separate NVR or storage device.
Fig 1.2 Fig 1.2.1
7
www.vip-vision.com
VDIRME Series | Surveillance Cameras
1.4 Waterproofing
Note: Waterproofing is applied on the Network Port connector.
Note: Waterproofing may differ - this is only applicable to the ‘VDIRM Series’ cameras.
1. Install the ruber ring into the network port, keep the smaller hole of the rubber ring outward and install the fixing
rubber ring onto the main body of the waterproof cable.
2. Pull the network cable (without the crystal head) through the main body of the waterproof connector, fixing
rubber ring and waterproof locking cover, make the crystal head of network cable, and then insert into the
network cable.
3. Put the main body of the waterproof connector on the network port and rotate it clockwise to lock the network
port and waterproof connector firmly.
4. Put the waterproof locking cover on the main body of the waterproof connector and rotate it clockwise to lock
the waterproof connector and waterproof locking cover firmly.
1.3 Cable management
Lead the cable out through ceiling/wall, which can
protect and hide the cable effectively.
Lead the cable out through side exit and add metal
conduit, to prevent cable from being damaged.
Bottom Wiring: Side Wiring:
www.vip-vision.com
Note:
This quick install guide is for reference only. Slight difference may be found in user interface.
All the designs and software here are subject to change without prior written notice.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.
For the full user manual, instructional videos, tips for using your surveillance system and
warranty information, please visit:
Your local VIP Vision™ IP solutions professional: www.activeonline.com.au 1300 816 742
Otros manuales para VDIRME Series
1
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vip-Vision
Vip-Vision
Vip-Vision VDIRME Series Manual de usuario
Vip-Vision
Vip-Vision SLR-B Series Manual de usuario
Vip-Vision
Vip-Vision SLR-B Series Manual de usuario
Vip-Vision
Vip-Vision Solar Series Manual de usuario
Vip-Vision
Vip-Vision PTZIRW Series Manual de usuario
Vip-Vision
Vip-Vision SLR-B Series Manual de usuario
Vip-Vision
Vip-Vision Pinhole Series Manual de usuario
Vip-Vision
Vip-Vision SLR-B Series Manual de usuario
Vip-Vision
Vip-Vision Panoramic Series Manual de usuario
Vip-Vision
Vip-Vision VDIRM Series Manual de usuario
