Vintage view W Series Manual de usuario

W Series Magnum/Champagne Wine Racks

Installation instructions for MAG1/MAG2 models

Included Parts

• (1) Base strip

• (1) Neck strip

• (6) mounting hole caps

• (2) Plastic Couplers

• (4) Spiral drywall

anchors

• (6) screws

• (2) toggle bolts

Required Tools

• Phillips head screw driver

• Level

Important Note: This installation guide will assist you with installing the VintageView W Series Magnum Wine

Rack (MAG1, MAG2 models) into wood-backed or drywall surfaces. These models are suitable for most 1.5L

bottle sizes, all 750ml Champagne bottles, and some larger 750ml bottles (Pinot Noir).

If installing racks to W Series Frames, please use the install guide and hardware included with Frames.

Figure A Figure B

1. CHOOSE BOTTLE DIRECTION

Decide if you want the necks of the bottles facing left or

right, and identify the base from the neck strip (base fea-

tures wider support divots that rest lower on the rack).

2. MARK THE FIRST STRIP

Starting at least 3 1/4” (83mm) — 2¾” (70mm) for

Champagne bottles — from adjacent wall or other

obstructions for 1.5L bottles. Hold the ﬁrst Mounting

Strip in place against the wall in desired location

(Figure A). Ensure the Strip is plump using a Level

and mark the hole locations with a Pencil. Set the

Strip aside.

SCAN THE QR CODE TO FIND YOUR PRODUCT

DOWNLOAD THE FREE APP

3D-GUIDED INTERACTIVE ASSEMBLY

INSTRUCTIONS CAN BE FOUND ON BILT

Before you begin

• Pencil

• Tape Measure

• Drill

• 1/16” (1.6mm) Drill Bit

• 13/32” (10.5mm) Spade Bit

Instructions: W Series Magnum Wine Racks (MAG1/MAG2)

Figure E

3. MARK THE NEXT STRIP

For the second Mounting Strip location, use a level to

measure 8 1/2” (216mm) from one of the ﬁrst Mount-

ing Strip holes and mark the location for the centerline

of the second Strip (Figure B).

Hold the second Mounting Strip in place against the

wall centered on the mounting mark. Ensure the Strip is

plumb using a Level and mark the remaining hole loca-

tions with a Pencil. Double check the locations are level

with those marked for the ﬁrst Strip. Set the Strip aside.

If Installing racking for 750ml Champagne bottles, use

7 1/2” (190.5mm) for Champagne bottles for center-

line.

IMPORTANT: If installing W Series 750ml or W Series

Big Bottle Racks, reference speciﬁc instructions for prop-

er centerline distances.

4. (OPTIONAL) MEASURE

ADDITIONAL COLUMNS

If installing multiple columns, mark the centerline for the

next Strip 6 1/2” (166mm) from the second mark, and

mark again 8 1/2” (126mm) for the distance between

the Neck and Base Strips (Figure C).

Note: Use 5 1/2” (166mm) and 7 1/2” (190.5mm),

respectively, for 750ml Champagne or Pinot Noir bot-

tles.

5. (OPTIONAL): PREPARE RACKS TO STACK

W Series Magnum Wine Racks are designed to stack,

one on top of the other (Figure D). If connecting Racks

vertically, remove the Endcaps from the Strips before

mounting to the wall and replace them with supplied

Couplers.

6. DETERMINE WALL SURFACE

Drill 1/16” (1.5mm) pilot holes at the marked locations

to determine if installing into drywall or wood studs/

backing (Figure E).

Figure E

Figure C

Figure D

Figure F

8 1/2”

(216mm)

8 1/2”

(216mm)

6 1/2”

(166mm)

Instructions: W Series Magnum Wine Racks (MAG1/MAG2)

7. DRILL MOUNTING HOLES

For Drywall

For the top mounting point, drill a 13/32” (10.5mm)

hole for a Toggle Bolt (Figure E). For the lower two holes

use a Phillip’s head screw driver to screw the Spiral

Drywall Anchors in the wall until the anchor is ﬂush with

the wall (Figure G).

For wood or stud

Skip to end of step 8.

8. HANG THE STRIPS

For Drywall

Insert one Toggle Bolt into the top mounting hole of either

the Base or Neck Strip (Figure H). With the wings of the

Expanding Nut oriented to fold toward the Bolt head,

thread the Expanding Nut onto the Bolt so that the tip of it

starts to protrude from the end of the nut.

Hold the Strip so the Bolt aligns with the top mounting

hole and gently push the Nut through the wall. Ensure the

wings have fully expanded on the back side of the wall

(Figure I).

Important: If the Expanding Nut does not fully open

behind the wall, the Mounting Strip may come out of the

wall.

Secure the bottom of the Strip using two (2) screws. Verify

the Strip is Plumb and fully tighten the Toggle Bolt using a

Phillips Head Screwdriver. Repeat with Second Strip.

For Wood

Attach one (1) Neck Strip and one (1) Base Strip to the

wall at marked hole locations using six (6) Screws (Fig-

ure J). Ensure each Strip is Plumb and level before fully

tightening.

9. INSTALL MOUNTING HOLE CAPS

Press three (3) mounting hole caps into the ½” holes on

the face of the each Strip.

Figure I

Figure E

Figure G

Figure H

Figure J

Instructions: W Series Magnum Wine Racks (MAG1/MAG2)

Figure L

10. OPTIONAL: CONNECTING

STRIPS VERTICALLY

When stacking the Racks, connect another Strip to the

Plastic Coupler (Figure K). Ensure that the Strip is Plum

with a Level and mark the mounting holes. Then repeat

the previous steps to attach the Strip.

11. ADD WINE

Only the good stuff.

____________________________

Problems?

Try Vino Pins installation using BILT 3D intelligent instruc-

tions, visit www.vintageview.com or give us a call at

303-504-9463.

Additional Notes:

All installations into drywall require the use of collars

and alternate fasteners to properly support the Vino

Pins. Any application outside of these parameters is not

warranted by VintageView and may result in product

and/or installation failure, property damage and/or

bodily injury.

Maintenance and Care:

VintageView W Series Magnum Wine Racks should be

regularly checked for tightness. Should any Rack to be

found to be loose, remove mounting hole covers and

tighten with screwdriver to secure.

If the face of the wall surface shows signs of break-

age, discontinue use immediately until the wall may be

adequately repaired. W Series Magnum Wine Racks

may be cleaned with a damp cloth and mild dish soap.

Abrasive pads or steel wool should NOT be used as

they will damage the ﬁnished surfaces of the parts.

Figure K

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de Vintage view

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view Vino Flex Series Manual de usuario

Vintage view

Vintage view Flex Vino Series Manual de usuario

Vintage view

Vintage view FCF-2WB Manual de usuario

Vintage view

Vintage view Half Island Manual de usuario

Vintage view

Vintage view Evolution Wine Wall Post Manual de usuario

Vintage view

Vintage view IDR Series Manual de usuario

Vintage view

Vintage view LP-FCP-10 Manual de usuario

Vintage view

Vintage view FCF-HD Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view Vino Series Manual de usuario

Vintage view

Vintage view IDR3 Manual de usuario

Vintage view

Vintage view W Series Single Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view Le Rustique Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Vintage view

Vintage view W Series Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario