VigilLink VLIP-JP1G-CTRL Manual de usuario
VLIP-JP1G-CTRL
VER 1.0
AV over IP Controller for JPEG 2000
Thank you for purchasing this product
Please read these instructions carefully for optimum performance and safety
before connecting, operating, or adjusting this product. Please keep this manual
for future reference.
A surge protection device recommends.
This product contains sensitive electrical components that electrical spikes
may damage, surges, electric shock, lightning, etc. Using a surge protection
system is highly recommended to protect and extend the life of your
equipment.
Table of Contents
1. Introduction. .........................................................................................
1
2. Features. ...............................................................................................
1
3. Package Contents. ..............................................................................
1
4. Specifications. ......................................................................................
2
5. Operation Controls and Functions. .....................................................
2
5.1 Front Panel......................................................................................
2
5.2 Rear Panel. .....................................................................................
3
5.3 IR Pin
Definition.
...............................................................................
4
6. Rack Mounting Instruction...................................................................
4
6.1 6U Rack
Mounting.
..........................................................................
4
6.2 1U Rack
Mounting.
..........................................................................
6
7. Web GUI User Guide. ...........................................................................
7
7.1 Preparation before Entering the
System.
.......................................
7
7.2 Functions and
Operation.
...............................................................
15
8. Application Example...........................................................................
27
1/29
1. Introduction
This Video over IP Controller controls and manages JPEG2000 IP products.
It supports dual 100M network ports, which can realize dual-network isolation
of the Control network and Multicast video distribution network. Built-in Web
GUI, TCP, and RS-232 control are supported. It supports POE function and
wide band 12V IR signal receiving. This IP Controller has the flexibility to be
widely applied to the growing need for IP products in today’s digital world,
commonly used in more and more different scenarios.
2. Features
☆Easy to create projects, control and manage the system
☆IP Configurations Flexibility - supports three types: Auto, DHCP, and
Manual☆HTTPS, SSH, SFTP security compatible
☆Built-in Web GUI control interface, supporting Drag & Drop operations
☆Supports image preview
☆Supports video, audio, RS-232, IR, KVM control, and management of the
distributed system
☆Dual network ports (VIDEO LAN port supports POE function) to isolate
Controls and Multicast networks.
☆Supports LAN/RS-232 port control and third-party central control
☆Supports IR signal receiving (3.5mm audio jack, 12V level)
☆4 channel GPIO control ports (5V/12V optional level)
☆Multiple circuits protection, lightning protection, and ESD design
☆Reliable system design, ensuring 7*24 hours reliable and stable work
3. Package Contents
①1 ⅹVideo over IP Controller
②1 ⅹ20kHz-60kHz 12V IR Receiver Cable (1.5 meters)
③1 ⅹ3-pin 3.81mm Phoenix Connector (Male)
④1 ⅹ6-pin 3.81mm Phoenix Connector (Male)
⑤ 2 ⅹ Mounting Ears
⑥ 4 ⅹ Machine Screws (KM3*6)
⑦1 ⅹ12V/1A Locking Power Adaptor
2/29
⑧1 ⅹUser Manual
3/29
4. Specifications
Technical
Network Bandwidth 100M
Transmission
Distance 100m CAT 5E/6/6A/7
Control Ports
2 x 100M LAN [RJ45 connector] [VIDEO LAN support POE]
1 x IR IN [3.5mm audio jack, 12V level]
1 x DIGITAL I/O [6-pin 3.81mm phoenix connector]
1 x RS-232 [3-pin 3.81mm phoenix connector]
Dimensions
204mm(W)×98mm(D)×21mm(H)
Housing
Metal Enclosure
Color Black
Weight 509g
Power
Supply 12V/1A
Power
Consumption 4.5W
Operating
Temperature
0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature
-20°C ~ 60°C / -4°F ~ 140°F
Relative
Humidity 20~90% RH (non-condensing)
5. Operation Controls and Functions
5.1 Front Panel
1 2 3
4/29
No.
Name
Function Description
1RESET Button
Press and hold this button (about 10 seconds) until Status
LED starts flashing; Controller will be reset automatically.
2POWER LED The red LED will light on when the Controller is powered on.
3
STATUS LED
The status LED will flash in yellowish-green every 1 second
until the l Controller boots complexity,yely,
and Control LAN
is read; then,n it becomes solid.
5.2 Rear Panel
No.
Name
Function Description
1DC 12V DC 12V/1A power input port.
2VIDEO LAN
(POE)
100M Video LAN port, supporting POE function.
Note: DC 12V/1A power supply is not required when POE
is enabled.
3CONTROL
LAN
The TCP/IP control network port.
4
MCU/Normal
DIP Switch
Normal mode (Default):
The RS-232 port is used for serial
port command control.
MCU mode: The RS-232 port is used for MCU software
upgrade.
53-pin Phoenix
Connector RS-232 serial communication port.
66-pin Phoenix
Connector
4 channel I/O level outputs, 1 channel grounding,
and 1 channel power supply to the outside.
7IO LEVEL
DIP Switch
It is used to control I/O level output and VOUT
voltage. Switch to left: 5V I/O level output, VOUT is
5V. Switch to right: 12V I/O level output, VOUT is
12V.
8IR IN 12V IR signal input port.
1
2
3
4
5
6
7
8
VOUT
IO4
IO3
IO2
IO1
5/29
5.3 IR Pin Definition
IR RECEIVER
6. Rack Mounting Instruction
6.1 6U Rack Mounting
This Controller can be mounted in a standard 6U rack (Please contact your
supplier for a 6U rack sale). The mounting steps are as follows:
Step 1: Use included screws to fix two mounting ears on the Controller, as
shown in the figure below:
IR RECEIVER
Power 12V
6/29
Step 2: Insert the Controller with mounting ears into a 6U rack (up to 10
units can be installed vertically), as shown in the figure below:
Step 3: Use screws to fix mounting ears on the rack to complete the
mounting, as shown in the figure below:
7/29
6.2 1U Rack Mounting
This Controller also can be mounted in a standard 1U rack (up to 4 units can
be installed horizontally). The mounting steps are as follows:
Step 1: Stack two Controllers on top of each other, then use included screws
to fix two 1U rack panels on the Controllers, as shown in the figure below:
Step 2: Fix two 1U rack panels on another two stacked Controllers in the
same way, then use screws to fix two 1U rack panels together, as shown
in the figure below:
Step 3: Fasten screws between two 1U rack panels so that four Controllers
are mounted in a 1U rack, as shown in the figure below:
8/29
7. Web GUI User Guide
7.1 Preparation before Entering the System
You can use Controller’s Web GUI to control all IP products at the Switch.
The operation method is shown below:
Step 1: Input the Controller’s default IP address (192.168.0.225) or the URL
(http://controller.local) into the Web browser address bar on the PC to enter the
Web GUI login interface.
Select the initial username (admin) and input the initial password (1234) on
the above login interface. Then, click “Log In” to enter the Web GUI interface.
For the first time, you need to set up the project, as shown in the following
figure:
Tabla de contenidos
Otros manuales de Controladores de VigilLink
