Viessmann VITOLIGNO 300-P Instrucciones de funcionamiento
Service instructions
for contractors
VIESMANN
Vitoligno 300-P
Type VL3B
Pellet boiler
For applicability, see the last page
VITOLIGNO 300-P
5692 891 GB 6/2011 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These instructions are exclusively
designed for qualified contractors.
■ Work on electrical equipment must
only be carried out by a qualified elec-
trician.
■ The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following when working on
this system:
■ National installation requirements
■ Legal instructions regarding the pre-
vention of accidents
■ Legal instructions regarding environ-
mental protection
■ The Code of Practice of relevant trade
associations
■ All current safety regulations as
defined by DIN, EN, DVGW, VDE and
all locally applicable standards
aÖNORM, EN and ÖVE
cSEV, SUVA, SVTI and SWKI
Working on the system
■ Isolate the system from the power sup-
ply (e.g. by removing the separate fuse
or by means of a mains isolator) and
check that it is no longer 'live'.
■ Safeguard the system against unau-
thorised reconnection.
!Please note
Electronic assemblies can be
damaged by electrostatic dis-
charges.
Before beginning work, earthed
objects, such as heating or water
pipes, must be touched to dissi-
pate any static charge.
Repair work
!Please note
Repairing components that fulfil a
safety function can compromise
the safe operation of your sys-
tem.
Replace faulty components only
with original Viessmann spare
parts.
Safety instructions
Safety instructions
5692 891 GB
3
Auxiliary components, spare and
wearing parts
!Please note
Spare and wearing parts that
have not been tested together
with the system can compromise
its function. Installing non-author-
ised components and making
non-approved modifications or
conversions can compromise
safety and may invalidate our
warranty.
For replacements, use only orig-
inal spare parts supplied or
approved by Viessmann.
Safety instructions
Safety instructions (cont.)
5692 891 GB
4
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance.......................................... 5
Further details regarding the individual steps....................................................... 6
Codes
Resetting codes to their delivered condition......................................................... 54
Code 1.................................................................................................................. 54
Code 2.................................................................................................................. 60
Service scans
Service functions.................................................................................................. 80
Temperatures, boiler coding card and brief scans............................................... 80
Scanning operating conditions and sensors ........................................................ 85
Troubleshooting
Fault display......................................................................................................... 86
Repairs................................................................................................................. 95
Function description
Display and control elements............................................................................... 114
Control functions.................................................................................................. 114
Allocation of heating circuits to remote control..................................................... 129
Vacuum supply system........................................................................................ 130
Pellet combustion sequence chart....................................................................... 131
Designs
Connection and wiring diagram............................................................................ 133
Parts lists............................................................................................................ 139
Commissioning/service reports........................................................................ 150
Specification....................................................................................................... 151
Certificates
Declaration of conformity...................................................................................... 153
Keyword index.................................................................................................... 154
Index
Index
5692 891 GB
5
For further information regarding the individual steps, see the page indicated
Commissioning steps
Inspection steps
Maintenance steps Page
•1. Filling the heating system.............................................. 6
••• 2. Checking all connections on the heating water side
for leaks
•3. Completing the commissioning checklist
•4. Switching the power on................................................. 6
•5. Language selection........................................................ 11
• • 6. Setting the time and date............................................... 12
•7. Configuring the supply system..................................... 12
•8. Commissioning the supply system.............................. 12
•9. Setting supply times for fuel supply (with vacuum
system)............................................................................ 13
•10. Matching the control unit to the heating system ........ 13
•11. Checking outputs (actuators) and sensors.................. 39
•12. Adjusting the heating curves........................................ 41
•13. Integrating a control unit into the LON......................... 44
• • 14. Shutting down the system............................................. 46
• • 15. Cleaning the combustion chamber............................... 47
•16. Cleaning secondary heating surfaces.......................... 48
•17. Cleaning the flue gas fan and Lambda probe.............. 49
• • 18. Emptying the ash container (if required)...................... 50
• • 19. Checking the diaphragm expansion vessel and
system pressure............................................................. 51
••• 20. Checking the function of safety valves
•21. Display "Maintenance"................................................... 52
•22. Instructing the system user........................................... 53
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance
5692 891 GB
6
Filling the heating system
A
1. Check the pre-charge pressure of the
diaphragm expansion vessel.
If the pre-charge pressure is lower
than the static system pressure, top
up with nitrogen until the pre-charge
pressure has risen 0.1 to 0.2 bar.
Adjust the pre-charge pressure
accordingly if it is too high.
2. Open the check valves.
3. Top up your heating system with
water and vent until the charge pres-
sure is 0.1 to 0.2 bar higher than the
pre-charge pressure of the dia-
phragm expansion vessel.
Permiss. operating pressure: 3 bar
Test pressure: 4 bar
4. Mark the charge pressure at pressure
gauge A.
5. Return the check valves to their oper-
ating position.
Switching the power on
After switching the power on, a commissioning sequence commences:
■ Select language
■ Set time and date
■ Supply system configuration
■ Supply system commissioning
When configuring the supply system, the
following are available for selection:
Commissioning, inspection, maintenance
Further details regarding the individual steps
5692 891 GB
7
– "Only holding hopper" for pellet sup-
ply only from the boiler hopper with man-
ual charging (not shown).
– "Suction system" for pellet supply via
screw conveyor discharge from a pellet
store and onward transportation via a
vacuum system:
Commissioning, inspection, maintenance
Further details regarding the individual steps (cont.)
5692 891 GB
8
– "Auger system" for pellet supply via
screw conveyor supply system from a
pellet store:
Commissioning, inspection, maintenance
Further details regarding the individual steps (cont.)
5692 891 GB
9
– "Suction system + silo" for pellet
supply from a pellet silo via vacuum sup-
ply system:
Commissioning, inspection, maintenance
Further details regarding the individual steps (cont.)
5692 891 GB
10
– "Auger + silo" for pellet supply from a
pellet silo via screw conveyor supply sys-
tem:
Commissioning, inspection, maintenance
Further details regarding the individual steps (cont.)
5692 891 GB
Otros manuales para VITOLIGNO 300-P
4
Tabla de contenidos
Otros manuales de Caldera de Viessmann
Viessmann
Viessmann VITOROND 200 Instrucciones de funcionamiento
Viessmann
Viessmann VITOPLEX 200 Manual de usuario
Viessmann
Viessmann Vitolig 200 Guía de inicio rápido
Viessmann
Viessmann ECV Series Guía rápida
Viessmann
Viessmann Vitodens 222-F Guía de inicio rápido
Viessmann
Viessmann VITOLADENS 300-W Guía de inicio rápido
Viessmann
Viessmann Vitodens 100-W Guía rápida
Viessmann
Viessmann VITODENS 200 WB2 Series Manual de usuario
Viessmann
Viessmann Vitoflame 300 VHG III Instrucciones de funcionamiento
Viessmann
Viessmann Vitodens 300 Manual de usuario
Viessmann
Viessmann VITOPLEX 300 Instrucciones de funcionamiento
Viessmann
Viessmann VITODENS 333 Instrucciones de funcionamiento
Viessmann
Viessmann VITOMAX 200-LW Manual de usuario
Viessmann
Viessmann Vitoladens 300-C Manual de usuario
Viessmann
Viessmann Vitodens 111-W Manual de usuario
Viessmann
Viessmann Vitodens 222-F Guía rápida
Viessmann
Viessmann Vitocrossal 200 CM2 Series Guía de inicio rápido
Viessmann
Viessmann Vitopend 100-W Manual de usuario
Viessmann
Viessmann VITOCELL 100-B Instrucciones de funcionamiento
Viessmann
Viessmann VITODENS 200 Manual de instrucciones
