Viega 8310.0 Manual de usuario
for concealed cistern 1H, concealed cistern 2H, retrofit to flush
plate Visign for Style or Visign for More
Model Year built:
8310.0 from 07/2007
en_INT
Drain valve set
Instructions for Use
Drain valve set 2 from 15
Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Area of application 6
2.2 Product description 7
3Handling 8
3.1 General mounting instructions 8
3.2 Assembly 8
3.2.1 Setting the flush volume 8
3.2.2 Removing the existing installation 9
3.2.3 Inserting the spare parts 12
3.3 Disposal 15
Table of contents
Drain valve set 3 from 15
1 About these instructions for use
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Drain valve set 4 from 15
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand-
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Drain valve set 5 from 15
2 Product information
2.1 Area of application
The drain valve set is intended for retrofitting existing WC installations in
such a way that one of the following Viega flush plates can be mounted:
nVisign for Style
– Model 8315.1
– Model 8331.1
– Model 8332.1
– Model 8332.3
– Model 8332.4
– Model 8333.1
– Model 8334.1
nVisign for More
– Model 8351.1
– Model 8352.1
– Model 8354.1
– Model 8357.1
The drain valve set can be inserted in one of the following WC elements
or WC modules:
nViegaswift
– Model 8000
– Model 8000.90
– Model 8000.99
– Model 8032
– Model 8039
– Model 8112
nSteptec
– Model 8461
nSystem Viega Eco Plus
– Model 8161.5
– Model 8161.80
– Model 8161.90
nMono
– Model 8310
The drain valve set can also be used as a spare part for the
concealed cistern 2H.
After mounting the spare part, the existing WC flush plate
can be re-mounted.
Product information
Drain valve set 6 from 15
2.2 Product description
1
2
3
4
7
6
5
Fig. 1: Drain valve set
1 mechanism
2 actuating rods
3 threaded bolts and screws for fastening the flush plate
4 bow
5 support
6 drain valve seat
7 drain valve
The drain valve was developed for the dual flush technology with a
small and a large flush volume. The small and large flush volumes are
actuated by pressing the small or the large button in the flush plate.
nImmediate re-flushing is possible because the cistern is not emptied
completely.
nThe small flush volume is set to approx. 3 l.
nThe large flush volume is set to approx. 6 l.
If required, both flush volumes can be increased. For setting the flush
volume, see:
ÄChapter 3.2.1 „Setting the flush volume“ on page 8
Flushing technology
Factory settings of the flush volume
Product information
Drain valve set 7 from 15
3 Handling
3.1 General mounting instructions
When you intend to install a new flush plate after retrofitting
to the new flush valve, the parts of the existing flush plate
can be discarded after dismounting.
3.2 Assembly
3.2.1 Setting the flush volume
Before mounting the drain valve set, set the flush volume at the drain
valve as follows:
Set the small flush volume at the slide control at the side of the
overflow pipe.
nSlide control in top position: approx. 3 litres
nSlide control in bottom position: approx. 4 litres
Set the large flow volume at the slide control at the bottom of the
drain valve.
nSlide control in left position: approx. 6 litres
nSlide control in right position: approx. 9 litres
Handling
Drain valve set 8 from 15
3.2.2 Removing the existing installation
The flush plate installed in your existing installation may
differ from the plate shown in the illustration. However, the
steps for removal will usually correspond to the steps
shown in the following.
To remove the existing installation, proceed as follows:
Remove the flush plate.
Pull the plate off the wall as straight as possible.
Loosen the support at the top and the bottom and remove it from
the installation shaft straight forward.
Loosen the knurled nuts on the left and right side.
Remove the basic panel.
Handling
Drain valve set 9 from 15
Loosen the threaded bolts with a 90° turn.
Remove the threaded bolts.
Remove the cover straight forward from the installation shaft.
Use a flat-blade screwdriver to turn the lock of the mechanism anti-
clockwise through 90° to release the mechanism.
Remove the mechanism from the installation shaft and dispose of it.
Remove the bow of the drain valve and dispose of it.
Close the corner valve to shut the water supply off.
Handling
Drain valve set 10 from 15
Tabla de contenidos
Otros manuales de Unidad de control de Viega
Viega
Viega 2275.2 Manual de usuario
Viega
Viega 2243.10 Manual de usuario
Viega
Viega Grundfix 4987 Manual de usuario
Viega
Viega 1252.1 Manual de usuario
Viega
Viega Multiplex Trio E Manual de usuario
Viega
Viega 1247.4 Manual de usuario
Viega
Viega Easytop 2170 Manual de usuario
Viega
Viega 9690TW Manual de usuario
Viega
Viega 56160 Hoja de instrucciones
Viega
Viega 8655.11 Manual de usuario
Viega
Viega PureFlow 2842.3ZL Hoja de instrucciones
Viega
Viega 8133.3 Manual de usuario
Viega
Viega PureFlow Crimp Zero Lead Hoja de instrucciones
Viega
Viega 2337.5 Manual de usuario
Viega
Viega 2235.2 Manual de usuario
Viega
Viega ManaBloc Hoja de instrucciones
Viega
Viega Grundfix Plus-Control Manual de usuario
Viega
Viega Easytop 2275.10 Manual de usuario
Viega
Viega PureFlow Crimp Hoja de instrucciones
Viega
Viega Easytop 2282 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
