Vicon V2000WM Manual de usuario
Vicon part no. 8006-8399-02-00 Rev 599 Section 7
X399
MODEL V2000WM
OUTDOOR WALL MOUNT
Copyright © 1999 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Lexan is a registered trademark of General Electric.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 516-952-CCTV (2288) FAX: 516-951-CCTV (2288) TOLL FREE: 800-645-9116
UK: 44/(0) 1489-566300 INFOFAX: 1-800-287-1207 WEB: www.vicon-cctv.com
X399 Rev 599 V2000WM Wall Mount Introduction •• 1
Introduction
The information in this instruction manual covers the installation of Model V2000WM Medium-Duty Outdoor Wall
Mount. This unit should only be installed by a qualified technician using approved materials in accordance with
national, state and local codes. Read this manual through completely before attempting installation.
The V2000WM Medium-Duty Outdoor Wall Mount is designed to support camera stations weighing up to a total
of 35 lb (16 kg), including pan-and-tilt or scanner, camera/lens system, and housing. Constructed of molded
Lexan, the V2000WM is suitable for outdoor applications. This unit accepts an optional adjustable head (Model
V2400AH) which provides full 360-degree rotation and a maximum of ± 60-degree tilt angle. If pole mounting is
necessary, the V20A Pole Mounting Adapter is available (see instruction manual X532).
Installation
Note: Use stainless steel hardware for all outdoor mountings.
Bolts or screws should extend through the structure with nuts and washers used on the opposite side. If the
mount must be attached to a blind structure with no access to the rear, make certain that the fasteners or studs
used have a minimum pull-out strength of 400 lb each. Studs should either be anchored in concrete or welded to
steel. (Never use lag screws in the end grain of wood.)
2•• Installation X399 Rev 599 V2000WM Wall Mount
V2000WM Wall Mount
To install the Model V2000WM wall mount, secure the base to the wall with at least four ¼-in. (7 mm) lag screws
or bolts. See Figure 1. Do not overtighten screws. Pull screws snug and then tighten ½ turn beyond snug
position. There are three additional knock-out holes that can be used as required. There is a feed-through hole
for routing cable through the mount. A bushing is supplied to prevent deterioration of the cable.
Figure 1
V2000WM Outline Drawing
V2400AH Adjustable Head
The V2400AH Adjustable Head consists of three parts: a circular base, a platform, and a clamping piece, plus
related hardware (3/8 in. hex bolt and washer). Refer to Figure 2.
1. Remove the bolt and washer from the accessory bag. Slide the washer onto the bolt up to the head, and
insert the bolt through the clamp and base. The washer prevents the bolt head from recessing into the
clamp. The threaded portion of the bolt protrudes about 3/8-inch (0.95 cm)from the bottom of the circular
base.
2. Align the adjustable head in the desired direction.
3. Thread the bolt into the threaded hole in the mount. Tighten the bolt finger tight, followed by an additional ½
turn.
X399 Rev 599 V2000WM Wall Mount Maintenance •• 3
Caution: Further tightening could damage the unit. Do not overtighten.
Figure 2
Installation of V2400AH Adjustable Head
Maintenance
Model V2000WM does not require any maintenance other than to clean out the drainage holes periodically (refer
to Figure 1).
4•• Shipping Instructions X399 Rev 599 V2000WM Wall Mount
Shipping Instructions
Use the following procedure when returning a unit to the factory:
1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of
the Vicon employee who issued the R.A.
Vicon Industries Inc.
89 Arkay Drive
Hauppauge, NY 11788
Phone: 516-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 516-951-CCTV (2288)
For service or returns from countries in Europe, contact:
Vicon Industries (U.K.) Ltd
Brunel Way
Fareham, PO15 5TX
United Kingdom
Phone: 44/(0)1489/566300; Fax: 44/(0)1489/566322
2. Attach a sheet of paper to the unit with the following information:
a. Name and address of the company returning the unit
b. Name of the Vicon employee who issued the R.A.
c. R. A. number
d. Brief description of the installation
e. Complete description of the problem and circumstances under which it occurs
f. Unit’s original date of purchase, if still under warranty
3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.
4. Mark the R.A. number on the outside of the carton on the shipping label.
X399 Rev 599 V2000WM Wall Mount Technical Information •• 5
Technical Information
MECHANICAL
Mounting: Four 1/4-inch lag screws.
Type: Fixed. (Adjustable with V2400AH).
Application: Indoor/Outdoor.
Load Rating: 35 lb (16 kg).
Cable Access: Hole provided in bottom of mount for routing cable.
Dimensions: Height: 7.4 in. (18.8 cm).
Width: 6.0 in. (15.2 cm).
Length: 20.9 in. (53.1 cm).
Weight: 7.2 lb (3.3 kg).
Construction: Molded Lexan.
Finish: Gray.
Tabla de contenidos
Otros manuales de Rack y soporte de Vicon
Vicon
Vicon V960D-KIT Manual de usuario
Vicon
Vicon V2100D-ICD Manual de usuario
Vicon
Vicon VM61514-5-MM Manual de usuario
Vicon
Vicon VCR-RK-1 Manual de usuario
Vicon
Vicon X517 Manual de usuario
Vicon
Vicon S2000-MSH-CM Manual de usuario
Vicon
Vicon KX-4-CC Manual de usuario
Vicon
Vicon V24WM Guía del usuario
Vicon
Vicon V2400WM Manual de programación
Vicon
Vicon VM614RK-2 Manual de usuario
Vicon
Vicon V1512MM-A Manual de usuario
Vicon
Vicon SVFT-UWM Manual de usuario
Vicon
Vicon V800ACM Manual de usuario
Vicon
Vicon IQeye IQA-FG Manual de usuario
Vicon
Vicon MPD-955-WM Manual de usuario
Vicon
Vicon V10AH Manual de usuario
Vicon
Vicon V2000D-PM Manual de usuario
Vicon
Vicon V2000B-BOX Manual de usuario
Vicon
Vicon V10UM Manual de usuario
Vicon
Vicon V1600AH Guía del usuario
