Viavi MTS 2000 Manual de usuario

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

► Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OCC Port, bulkhead

connectors, patch cables, etc.)

► Focus fiber on the screen. If dirty, clean the

end-face.

► If it appears clean, run inspection test.

► If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect

Figure 1: Equipment Requirements

Optical Spectrum Analyzers. The Best OSA Modules & Platforms (viavisolutions.com)

DWDM Optical Channel Checker

This quick card describes how to connect to a fiber under test, configure DWDM Optical

Channel Checker (OCC) test setups, run tests, and analyze results with a T-BERD/MTS-

2000 equipped with an OCC-4056C module.

Note: The OCC module is used to monitor wavelengths on a live network. Care

should be exercised when unplugging fibers from the network as the fibers

may be carrying traffic.

► T-BERD/MTS-2000 equipped with the

following:

► Fiber Optics Software Release V21.0 or

greater

► OCC-4056C DWDM OCC Module

► Fiber optic cleaning and inspection tools

► Fiber optic patch cable (Launch Cable)

► Optical Coupler to connect patch cable to

Fiber Under Test

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

Optical Spectrum Analyzers. The Best OSA Modules & Platforms (viavisolutions.com)

CONNECT TO FIBER UNDER TEST (FUT)

All fibers and connectors should be cleaned and inspected prior to connection, as described on page 1.

The Nano OSA is typically connected to the FUT via a Monitor Port or splitter/tap to not disrupt service.

The Nano OSA can also be directly connected to the common port or common fiber via a coupler during

turn up or maintenance:

1. Inspect the OCC port on top of the test set.

2. If connecting to the Common Cable, connect the Common

Cable to an optical coupler with the same connector type and

inspect the fiber end face in the coupler.

3. If connecting to the Monitor Port or Common Port on the Mux,

inspect the Mux Port.

4. Inspect the fiber end face of the Patch Cable and connect the

cable to the OCC port.

5. Inspect the other fiber end face of the Patch Cable and Connect

the Launch Cable to the coupler or Mux port.

Figure 3: OCC Port Inspection

Figure 4: Connecting to Monitor Port

Figure 5: Connecting to Common Cable

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

Optical Spectrum Analyzers. The Best OSA Modules & Platforms (viavisolutions.com)

CONFI G U RE T E ST SETUP

LAUNCH TEST

1. Press the ON/OFF button to start the

test set.

2. Press the Home button to display

the Home view with the OCC-4056cicon.

3. Tap the OCC-4056Cicon

until it is yellow and highlighted.

Figure 6: Home Screen

1. Tap Setup icon.

2. Tap Auto-set to auto-configure the OCC

for a single sweep.

3. If a splitter/tap is used to access the

signal, Tap the Analysis tab and set

Splitter Value to the splitter loss

(in dB or %).

Figure 7: Setup Menu

Figure 8: Analysis Settings

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

RUN SW EE P TE S T

3. Tap START icon (upper right) to run scan

4. View Results after scan completes. Use your finger or stylus to scroll up/down as needed.

Total # of

Channels

detected

Verify Channels &

Power Levels (dBm)

Measure offset

(detect optics going bad)

Measure

Actual wavelengths

Otros manuales para MTS 2000

Otros manuales de Equipo de prueba de Viavi

Viavi

Viavi ComXpert CX100 Manual de usuario

Viavi

Viavi OTU-8000 Manual de lista de piezas

Viavi

Viavi FIT-82P03 Manual de usuario

Viavi

Viavi Smart Class 4800 Manual de usuario

Viavi

Viavi SmartOTDR Manual de lista de piezas

Viavi

Viavi IFR 6000 Manual de lista de piezas

Viavi

Viavi ONX-220 Manual de usuario

Viavi

Viavi T-BERD/MTS 8000 Manual de lista de piezas

Viavi

Viavi OneAdvisor 1000 Manual de usuario

Viavi

Viavi T-BERD 5800 Manual de lista de piezas

Viavi

Viavi T-BERD MTS-580 Manual de lista de piezas

Viavi

Viavi T-BERD/MTS-5800 Manual de lista de piezas

Viavi

Viavi ComXpert CX100 Manual de usuario

Viavi

Viavi PSD90-3 Manual de usuario

Viavi

Viavi T-BERD/MTS 5800 Guía de instalación

Viavi

Viavi P5000i Manual de usuario

Viavi

Viavi SmartOTDR Mainframe Manual de usuario

Viavi

Viavi OLA-54 Manual de usuario

Viavi

Viavi AVX-10K Manual de usuario

Viavi

Viavi OneExpert ONX CATV 620 Manual de usuario

Viavi

Viavi MTS 2000 Manual de usuario

Viavi

Viavi T-BERD/MTS 5800 Manual de usuario

Viavi

Viavi T-BERD/MTS-4000 v2 Manual de lista de piezas

Viavi

Viavi T-BERD/MTS 5800 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario