Viavi Certifier Series Manual de usuario
CERTIFIER40G
MPO Certification Testing
User Manual
Certifier Series (C40G)
Notices
No part of this manual may be reproduced in any form or by any means (including electronic
storage andretrievalor translation intoa foreignlanguage) without prior agreement and written
consent from Viavi Solutions as governed by international copyright Laws.
Warranty
The material contained in this document is provided “as is,” and is subject to being
changed, without notice, in future editions. Further, to the maximum extent permitted
by applicable law, disclaims all warranties, either express or implied, with regard to this
manual and any information contained herein, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. Viavi Solutions shall
not be liable for errors or for incidental or consequential damages in connection with
the furnishing, use, or performance of this document or of any information contained
herein. Should Viavi Solutions and the user have a separate written agreement with
warranty terms covering the material in this document that conflict with these Terms,
the warranty terms in the separate agreement shall control.
WARNING
A CAUTION notice denotes a hazard.
It calls attention to an operating procedure, practice, or the like that, if not
correctly performed or adhered to, could result in damage to the product or
loss of important data. Do not proceed beyond a CAUTION notice until the
indicated conditions are fully understood and met.
CAUTION
Operating procedure, practice, if not correctly performed or adhered to, could
result in personal injury or death. Do not proceed beyond a WARNING notice
until the indicated conditions are fully understood and met.
General Safety Information
WARNING
Do not use the device if it is damaged. Before you use the device, inspect the casing.
Look for cracks or missing plastic. Do not operate the device around explosive gas,
vapor, or dust.
Always use the device with the cables provided.
Observe all markings on the device before establishing any connection.
When servicing the device, use only the specified replacement parts.
Do not operate the device with the cover removed or loosened.
Use only the power adapter provided by the manufacturer to avoid any unexpected
hazards.
CAUTION
If the device is used in a manner not specified by the manufacturer, the device protection may
be impaired.
Always use dry cloth to clean the device. Do not use ethyl alcohol or any other volatile liquid to
clean the device.
Do not permit any blockage of the ventilation holes of the device.
Environmental Conditions
This instrument is designed for indoor use and in an area with low condensation. The table
below shows the general environmental requirements for this instrument
Environmental conditions Requirements
Operating Temperature 0 °C to 40 °C
Operating humidity 20% to 85% RH non-condensing
Relative humidity 10% to 80%
NOTE
The CERTIFIER40G, CERTIFIER10G complies with the following Safety and Regulatory
requirements.
DIN EN 55024, Edition:2003-10 (IEC/CISPR 24:1997, modified + A1:2001 + A2:2002); EN
55024:1998 + A1:2001 + A2:2003
DIN EN 55022; VDE 0878-22:2008-05 (IEC/CISPR 22:2005, modified + A1:2005); EN
55022:2006 + A1:2007
Regulatory Markings
The CE mark is a registered trademark of
the European Community. This CE mark
shows that the product complies with all
the relevant European Legal Directives.
Manufacturer‘s Name
Psiber Data Pte. Ltd
Manufacturer’s Address
3 Science Park Drive #03-08,
The Franklin Singapore Science Park 1,
Singapore 118223
Declares under sole responsibility that the product as originally delivered
Description
Cable Certification Tester Kit
Equipment
Cable Certifier
Complies with the essential requirements of the following applicable European Directives and
carries the CE marking accordingly:
DIN EN 55024, Edition:2003-10 (IEC/CISPR 24:1997, modified + A1:2001 + A2:2002); EN
55024:1998 + A1:2001 + A2:2003
DIN EN 55022;
VDE 0878-22:2008-05 (IEC/CISPR 22:2005, modified + A1:2005);
EN 55022:2006 + A1:2007
Signature
Arvind C Patel
Quality Management
Psiber Data Pte. Ltd.
www.psiberdata.com
Date :
December 14, 2010
Declaration of Conformity
Contents
Chapter 1: Getting Started ..................................................................................................................8
Unpacking the box................................................................................................................... 8
Chapter 2: Configuring Certifier.........................................................................................................9
Certifier User Interface............................................................................................................. 9
Touch Screen Layout................................................................................................................ 9
The One Touch Access Buttons ............................................................................................... 11
Chapter 3: Setting Reference............................................................................................................17
Chapter 4: Configuring an AUTOTEST............................................................................................19
Testing Guide for 12-core MPO Testing.................................................................................... 20
Chapter 5: Performing an AUTOTEST .............................................................................................21
Managing test result(s) .......................................................................................................... 23
Exporting test results into J-Report PC Software........................................................................ 24
1
Chapter 1: Getting Started
Unpacking the box
MPO
Power Meter (Local)
Adapter
Light Source (Remote)
Adapter
Type A Tail Cords
Type A Reference Cord
Type B Reference Cord
Mating Couplers
2
Chapter 2: Configuring Certifier
Certifier User Interface
Touch Screen Layout
The Graphical User Interface (GUI) in version 7.0’s firmware has been updated with a
more responsive system and quick-access menus.
Certifier boots up to the SETUP screen. It is categorised into 5 groups:
1. Status bar
2. Configuration group
3. Test Settings group
4. Project Settings group
5. System Settings group
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de prueba de Viavi
Viavi
Viavi FIT-82P03-PRO Manual de usuario
Viavi
Viavi 3900 Series Manual del propietario
Viavi
Viavi HST-3000 Manual de lista de piezas
Viavi
Viavi T-BERD 6000A V2 Manual de usuario
Viavi
Viavi RGS-2000NG Manual de usuario
Viavi
Viavi 3900 Series Manual del propietario
Viavi
Viavi T-BERD MTS 5800 Manual de lista de piezas
Viavi
Viavi PSD90-3 Manual de usuario
Viavi
Viavi SmartPocket OLP-39G Manual de usuario
Viavi
Viavi ALT-9000 Manual de lista de piezas
Viavi
Viavi T-BERD MTS 5800 Manual de lista de piezas
Viavi
Viavi T-BERD 5800 Manual de usuario
Viavi
Viavi FBP-HD4iP Manual de usuario
Viavi
Viavi SmartClass Fiber MPOLx Manual de lista de piezas
Viavi
Viavi FIT-82P03 Manual de usuario
Viavi
Viavi 8100 V2 Series Manual de usuario
Viavi
Viavi FBP-HD4i Manual de usuario
Viavi
Viavi HST-3000 Manual de lista de piezas
Viavi
Viavi T-BERD/MTS 4000 Manual de usuario
Viavi
Viavi T-BERD/MTS 8000 Manual de lista de piezas
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
