Viatom Visual Oxy Manual de usuario

Visual Oxy

Wrist Pulse Oximeter

User Manual

English|Deutsche|Italiano|Español|Français

Contents

User Manual…….…...........…..English 1-13

Benutzerhandbuch...........…...Deutsch 14-26

Manuale d'uso........…..…....…Italiano 27-39

Manual de usuario………….....Español 40-52

Manuel de l'utilisateu........…..Français 53-65

User Manual

User’s Manual

Contents

1. Introduction..................................................................2

2 Using the Monitor......................................................... 5

3 PC software (Optional).................................................. 9

4 Maintenance................................................................10

5 Troubleshooting...........................................................10

6 Specifications...............................................................11

7 Electromagnetic Compatibility....................................12

1. Introduction

1.1 Intended Use

This product is intended to be used for measuring,

displaying and storing of pulse oxygen saturation

(SpO2)，pulse rate and motion in home or healthcare

facilities environment. App can show real-time SpO2,

pulse rate; get record, display results and report.

Note:

The data and results provided by this device are for pre-check

screening purpose only and cannot be directly used for diagnostic

or treatment.

The data provided by the APP and PC software (optional) is not

intended for diagnosis or treatment purpose, always consult your

doctor for any health condition.

Warnings and Cautionary Advices

DO NOT squeeze the sensor or apply excessive force on

the sensor & cable.

Do not use this device during MRI examination.

Never submerge the device in water or other liquids. Do

not clean the device with acetone or other volatile solutions.

Do not place this device in pressure vessels or gas

sterilization device.

Consult your doctor immediately if you experience

symptoms that could indicate acute disease.

Do not self-diagnose or self-medicate on the basis of this

device without consulting your doctor. In particular, do not

start taking any new medication or change the type and/or

dosage of any existing medication without prior approval.

Use only cables, sensors and other accessories specified

in this manual.

Prolonged continuous SpO2monitoring may increase the

risk of undesirable changes in skin characteristics, such as

irritation, reddening, blistering or burns.

Check the SpO2sensor application site every 6-8 hours to

determine the positioning of the sensor and the circulation

and skin sensitivity of the patient. Patient sensitivity varies

depending on medical status or skin condition. For patients

with poor peripheral blood circulation or sensitive skin,

inspect the sensor site more frequently.

Functional tester cannot be used to assess the accuracy of

a SpO2sensor or a device.

This device is designed to determine the arterial oxygen

saturation percentage of functional hemoglobin. Factors

that may degrade pulse oximeter performance or affect the

accuracy of the measurement include the following:

- excess ambient light

- excessive motion

- electrosurgical interference

- blood flow restrictors

(arterial catheters, blood pressure cuffs, infusion lines,

etc.)

- moisture in the sensor

- improperly applied sensor

- incorrect sensor type

- poor pulse quality

- venous pulsations

- anemia or low hemoglobin -concentrations

- cardiogreen and other -intravascular dyes

- carboxyhemoglobin

- methemoglobin

- dysfunctional hemoglobin

1.2 Guide to Symbols

1.3 Unpacking

Main Unit × 1

Ring Sensor × 1

Cable × 1

User Manual × 1

Symbol

Description

Type BF-Applied Part

Manufacturer

European authorized representative

CE0197

CE Marking indicating conformance to

EC directive No. 93/42/EEC concerning

medical devices.

MRI unsafe. Presents hazards in all MR

environments as device contains

strongly ferromagnetic materials.

Indicate separate collection for electrical

and electronic equipment (WEEE).

IP22

Protected against spraying water and

against access to hazardous parts with a

tool, per IEC 60529.

Follow Instructions for Use.

Warning and Caution!

Serial number

No alarm system.

2 Using the Monitor

2.1 Charging

Charge the battery before using.

Use the charge cable to charge the battery of device in

the USB Port of the computer or with USB charging

adapter.

After being fully charged, the device will power off

automatically.

2.2 POWER ON/OFF

POWER ON:

Press the button for 1 second to turn on the device.

POWER OFF:

Automatically power off: The device will turn off

automatically in 2 minutes if no measurement, no

operation or without App connection.

Manually power off: You can press the button for about

2 seconds to turn off.

2.3 TAKE THE FIRST RECORDING

START. Wear the device and the Ring Sensor, press

the button to power on. And keep

yourself in the quiet environment.

(For the sake of clarity, recommendelly

the user wear the Checkme 02 watch

on their left wrist and put the ring

sensor on the thumb. If it is too tight, try another

finger. Avoid being loose.)

STOP. After the record, take off the Ring Sensor (and

the device), the recording will be save

after the countdown. (If the working

time is less than 1 minute, the data

will not be saved.)

Note:

The device can also work as a clock and pedometer

without ring sensor, and the steps will restart counting

after the ring sensor plugged in.

Please avoid excessive motion for the sensed finger

during recording and avoid any strong ambient light

condition.

We recommend using the classic monitor mode in daily

environments and the sleep mode when you want to

sleep.

2.4 Stop monitoring & sync data

Take off the sensor, the countdown will

begin.

During the countdown, if you wear the sensor again, the

record will be resumed.

After the countdown, the data will be ready for sync.

Note:

1. The duration of the recording is 1mins~10 hours.

And the device can Collect and store maximum 4

recording, when the 5th recording coming, the first

recording will be will covered.

Sync data to the ViHealth App

You can Sync the data to your app after

the countdown or next time after you

turn on the device.

Note: Refer the ViHealth app manual for more details.

2.4.1 How to find the Serial Number？

1）Detach the the main unit from wristband.

2）Flip the main unit over, the series number is

printed on the label of product.

Note:

The SN Serial number is on the back of the device

2.5 How to synchronize the time of the device

The time of the Checkme 02 will be automatically

synchronized with the network time on your smart

device after connected with the app.

Note: Refer the ViHealth app manual for more details.

2.6 Operation Mode Navigation

The device has two operation modes: Sleep Mode

and Monitor Mode.

Turn on the device, during the icon blinking, press the

button to switch between two modes.

Sleep Mode

Monitor Mode

Parameters

SpO2, PR, Motion

SpO2, PR, Steps

Screen

Activated by button

Always on

The Sensor

Vibrates

When SpO2is

lower than

threshold set

When SpO2is lower

than threshold set；

Or when step goal is

met

Bluetooth

On when the

screen lights up

Always on

Report

Sleep report

Monitor report

2.7 Smart Vibration

The vibrator in the ring sensor will be activated when

the SpO2fall below the preset value (Threshold). The

vibration will stop when the SpO2recover to normal

level or you can press the button to stop it.

You can customize the vibration to help you sleep better

via app or PC(Only for the Checkme 02 Pro).

2.8 Download App

App name: ViHealth

iOS: App Store

Android: Google Play

Compatibility

The device is compatible with iOS versions 9.0+ and

Android versions 5.0+. Refer the ViHealth app manual

for more details.

2.9 Bluetooth Connection

The device Bluetooth will be enabled automatically only

when the screen lights up.

Note: when the Checkme O2 is pairing with the smart

device, keep the screen lights up.

Note: DO NOT PAIR in the settings of your smart

device.

2.10 Display

Time, Remaining battery capacity

Sleep Mode

Monitor Mode

MODE

18:45

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo médico de Viatom

Viatom

Viatom Checkme Pro Manual de usuario

Viatom

Viatom Checkme Pro Manual de usuario

Viatom

Viatom Wellue Manual de usuario

Viatom

Viatom ER1 Manual de usuario

Viatom

Viatom Checkme O2 Manual de usuario

Viatom

Viatom Checkme Pro Manual de usuario

Viatom

Viatom OxySmart PC-60FW Manual de usuario

Viatom

Viatom Wellue POD-2 Manual de usuario

Viatom

Viatom BabyO2 Manual de usuario

Viatom

Viatom Checkme O2 Manual de usuario

Viatom

Viatom PO2 Manual de usuario

Viatom

Viatom ER2 Manual de usuario

Viatom

Viatom FS10C Manual de usuario

Viatom

Viatom Checkme Lite Manual de usuario

Viatom

Viatom PB-20 Manual de usuario

Viatom

Viatom OxySmart PC-60F Manual de usuario

Viatom

Viatom Wellue WearO2 Manual de usuario

Viatom

Viatom Checkme O2 Manual de usuario

Manuales populares de Equipo médico de otras marcas

TekTone

TekTone Tek-CARE160 Manual de usuario

NeuroMetrix

NeuroMetrix Quell 2.0 Manual de usuario

AMT

AMT XLR8 Manual de usuario

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manual de usuario

EDAN

EDAN SONOTRAX Pro Manual de usuario

Restorative Therapies

Restorative Therapies RT300 Manual de usuario

Gendex

Gendex Expert DC Manual de usuario

Dexcowin

Dexcowin ADX4000W Manual de usuario

Libelium

Libelium MySignals Manual de usuario

Acelity

Acelity V.A.C.ULTA 4 Manual de usuario

Caputron

Caputron ActivaDose II tDCS Manual de usuario

FujiFilm

FujiFilm Sonart Manual del propietario

Plinth 2000

Plinth 2000 93CDT Manual de usuario

GE SENOGRAPHE 800T Manual de usuario

GE Definium 5000 Manual de usuario

Kanmed

Kanmed GE-1380 Manual de usuario

Huntleigh

Huntleigh FD1 Manual de usuario

Stryker

Stryker SPR Plus Manual de usuario