Vetek JIK-6 Series Manual de usuario

Service Manual Indicator JIK-6 Page 1

Chapter I Basic Introduction

1-1 Dimension------------------------------------------------------------------------------- 1

1-2 Cross-reference List of Characters--------------------------------------------------- 1

1-3 Product Specification Sheet----------------------------------------------------------- 2

Chapter II Parameter Function Setting

2-1 General Parameter Setting------------------------------------------------------------ 3

2-2 Advanced Parameter Setting--------------------------------------------------------

2-3 Weighing Capacity, Sensed Weight Setting and Weight Calibration------------ 7

Chapter III Various Assemblies and Relevant Illustrations

3-1 Back Cover Assembly and Disassembly-------------------------------------------- 9

3-2 Installation of Additional Board------------------------------------------------------ 10

3-3 Wiring Cross-reference Chart--------------------------------------------------------- 11

3-4 Illustration of Contacts of Additional Board---------------------------------------- 12

Chapter IV Troubleshooting

4-1 Preliminary Examination-------------------------------------------------------------- 13

4-2 Error Message and Troubleshooting----------------------------------------------

---

4-3 Summary Table of Error Message-------------------------------------------------

---

Chapter V Structural Part of Platform Scale

5-1 Connection of Metal Connectors---------------------------------------------------

---

5-2 L/C Replacement Process------------------------------------------------------------

5-3 L/C-related Technology--------------------------------------------------------------

Chapter VI Exploded Drawing and Cross-reference List of Parts

6-1 JIK 6-CAB ------------------------------------------------------------------------------ 20

6-2 JIK 6-CSB ------------------------------------------------------------------------------ 21

6-3 JIK 6-CSN ------------------------------------------------------------------------------ 22

Vetek AB

Hantverksvägen 15, 76493 Väddö - Sweden

Tel_ +46176-208920, [email protected], www.vetek.com

Service_Manual_JIK-6_V1

Service Manual Indicator JIK-6 Page 2

Chapter I Basic Introduction

1-1. Dimension

1-2. Cross-reference List of Characters

0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z

Service Manual Indicator JIK-6 Page 3

1-3. Product Specification Sheet

Case Shell Material ABS plastics S/S stainless steel

Waterproof Grade N/A IP67

Dimension 230 * 150 * 90 mm

Display 6-digit 30mm high & 3-digit 10mm high LCD (including EL

backlight)

Unit Selection Kg or g, lb, Taiwan jin, liang, HK jin, liang, pcs, %

Power Supply Adaptor 9V/1A, Battery 6V/3Ah

Operating Environment -5 ~ 40

Storage Environment -20 ~ 60

Certification OIML (incl. CE)

Weight (incl. battery) Approx. 2.5kg Approx. 2.8 kg

Display-LCD S/S flat backboard (excl. battery)

6-digit 20mm high & 3-digit 9mm high - 7-Segment display

Options Display-LED Power Supply Adaptor 9V/1A (battery 6V/3Ah also available for

choice)

Model Basic Model Advanced Model

Conversion Mode ∆- Σ

Internal

Resolution Range About 1,000,000 counts About 5,000,000 counts

3,000d(OIML) 6,000d(OIML)

External

Resolution

Precision Max. 30,000d(non-OIML) Max. 60,000d(non-OIML)

Analogue/

Digital

Converter

Conversion Rate 10 times/sec.

System Linearity Error Within 0.01% of Full Load

Zero Drift ±10 ppm/ ±6 ppm/

Temperatur

e Factors Linear Drift ±3 ppm/ ±1.5 ppm/

Circuit Voltage 5VDC ± 6%, 120mA (max. 8 * 350Ω)

Applicable Range -2 ~ 18mV -10 ~ 40mV

2uV/d (OIML) 1uV/d (OIML)

Weight

Sensor Input Sensitivity Over 0.2uV/d (non-OIML) Over 0.1uV/d (non-OIML)

Calibration Options

Unit Selection Kg, g, lb Model Code Spec.

Weight

Calibration

Setting Point

Single-point or three-

point OP1 RELAY

Sensed Weight Selectable from 1, 2, 5

Basic/advan

ced model OP2 RS232 (RTC)

OP3

RS232-2port

(RTC)

Advanced

model OP4 Dual channel

Service Manual Indicator JIK-6 Page 4

Chapter II Parameter Function Setting

2-1 General Parameter Setting

(1) How to enter and change general parameter setting

Step I: Power on while holding down key or hold down key for about 3 seconds while power is on with

zero load.

Step II: Select parameter functions by pressing or key, and select parameter setting by pressing or

key.

Step III: After setting is completed, press key to return to weighing mode.

(2) General parameter function descriptions

Item Function Display Description

: Automatic power-off function off

: Automatic power-off after 5 minutes

: Automatic power-off after 10 minutes

: Automatic power-off after 30 minutes

:Automatic power-off after 60 minutes

Automatic Power-off

Overview: The scale

will be powered off

automatically after

elapse of the set time

when powered on but

not in use. :Automatic power-off after 90 minutes

:The internal buzzer makes the beep sound when the

calibration value is within the range.

: The internal buzzer makes the beep sound when the

calibration value is out of the range.

: The external buzzer makes the beep sound when the

calibration value is within the range.

Beep

Overview: Select beep

(warning) mode of

buzzer.

: The external buzzer makes the beep sound when the

calibration value is out of the range.

:Weight value holding function off

Holding the Weight

Value

Overview: The weight

value can be held.

Press key to hold the weight value, press

key to cancel.

Service Manual Indicator JIK-6 Page 5

Printing function not used

Normal external printer option

Special option for SH-24 printer (pin type can print

out “jin”)

Special option for BP-443 and 643 (self-adhesive

type can print out bar code)

Printer Selection

Overview: Use in

connection with a

printer.

Special option for EZ-2P printer (self-adhesive type

can print out bar code)



RS-232 Transmission

Rate

Overview: Baud rate

setting.



RS-232 Transmission

Format

Overview: Transmission

format setting in

connection with external

equipment like printer.

Parity

N: None E: Even O: Odd

Data Bit

7: 7bit 8: 8bit

Stop Bit

1: 1bit

: Backlight function off

: Backlight on

:Backlight on when weight value is stable, after 5

seconds, it will come off automatically.

Backlight Selection

Overview: Backlight

function setting.

: When weight is 20 times over sensed weight,

backlight is on.

Note: Items marked with an asterisk () stand for factory settings.

Service Manual Indicator JIK-6 Page 6

2-2 Advanced Parameter Setting

(1) How to enter and change advanced parameter setting

Step I: When power is on: hold down key for about 3 seconds to enter into [General Parameter], then press

key for about 3 seconds.

Step II: When power is off: press key to power on and enter into [General Parameter], then press key for

about 3 seconds.

Step III: Select parameter functions by pressing or key, and select parameter setting by pressing or

key.

Step IV: Press key twice to save the parameter setting, and return to weighing mode. If you

don’t want to save the parameter setting, press key.

(2) Advanced parameter function descriptions

Item Function Display Description

:% Normal power on to use is allowed

within ±10% (OIML)

: % Normal power on to use is allowed

within ±20%

:% Normal power on to use is allowed

within ±30%

:% Normal power on to use is allowed

within ±40%

A00

Initial Zero Point Range

Overview: The calibrated zero

point value shall serve as the

benchmark, and the zero point

range shall be calculated in

percentage of max. Weighing

value.

:% Normal power on to use is allowed

within ±50%

:%

A01

Range of Use of Zero Key

Overview: The zero key range

can be improved. : ~ %

The Zero key can be used for deduction

within ±2%, 3%, 4%… 20% (e.g. ±2% of

300kg= ±6kg)

A02 Return to Zero Symbol-

Display Range :Display of zero point symbol when

variation is ±0e (OIML)

Service Manual Indicator JIK-6 Page 7

Overview: To set the

conditions for appearance of

zero point symbol.

: ~ Appearance of zero point symbol when

variation is ±1e, 2e…±5e

:Off

:

A03

Zero Point-Tracking Range

Overview: To reduce zero drift

problems caused by

environment and other factors. : ~

1e/s…5e, however, when precision

setting is lower than 6100/1 (OIML), it

will be adjusted automatically into 0.5e/s.

:Off

A04

Power Down Mode

Overview: standby function

setting. : ~ Take effect in 1~10 minutes. (Press any

key to restore)

:OFF (without hysteresis effect)

: ~

:

A05

Hysteresis Selection

Overview: To reduce critical

drift problem. However, it is

not always better to set high

values. Test of effect must be

carried out with respect to

each segment.

: ~

:or 0 (no shockproof effect), 1(worst effect)

:

A06

Shockproof Factor

Overview: To reduce

interference caused by bad

operating environment. : ~

: ~ 1e~19e

:20e (OIML)

A07

Min. Weighing Capacity

Overview: Min. printing range

up to 1e. (Originally it requires

20e and above) :21e

:OFF (no filtering effect)

: ~

:

A08

Filtering Factor

Overview: To improve

unstable condition of the scale;

in principle, the higher setting

the better effect. : ~

1(worst), 2, 3… 9(best).

: . or . Display when variation is within 0.2e or

0.5e

A09 Stable Symbol Display

Range

Overview: To set the :Display when variation is within 1e

Service Manual Indicator JIK-6 Page 8

conditions for appearance of

stable symbol. : ~ Display when variation is within 2e~8e

:One-way transmission (output)

A10

RS232-Receiving Port

Selection

Overview: To select one-way

or two-way transmission.

:Two-way transmission (output/input)

:Initiation Delay function off.

: . Signal sent out in 0.5sec.

A11

Initiation Delay

Overview: RS232 sends out

signal several seconds after

stable appearance of stable

symbol.

: ~ Signal output in 1sec., 2 sec…4 sec.

:Weight memory function off.

A12

Weight Memory

Overview: To record the last

weighing value. :On (The function is applicable for

production line)

:No limit

A13

Min. Internal Use Limit

Overview: To limit sensor use

rate. :L/C use rate at least over 60%

:Weight display function not in use.

A14

Calibration Mode-Weight

Display

Overview: No need to restart

the machine after calibration.

:In use.

A15

Enlargement Ratio Selection

Overview: To adjust ratio of

internal value to external

value.

:Starting time is year 2000 but without

RTC detection function

:

A16

Starting Year Setting

Overview: Since RTC

calculation time is around 15

years, this setting may avoid

occurrence of problems similar

to Y2K.

The starting time calculation is based on

a scale of 4 years; you may select

between 2008~2100.

Note: Items marked with an asterisk () stand for factory settings.

Service Manual Indicator JIK-6 Page 9

2-3 Weighing Capacity, Sensed Weight Setting and Weight Calibration

Step I (Enter into calibration mode)

Sealed Type

(As shown in the right figure) release the screw

at the left back, power on while holding down

the [CAL] key at the back by use of a tool until

CAP is shown on the lower left screen, i.e. the

scale has entered into the calibration mode.

Non- Sealed Type: Turn on the scale by holding down key until CAP is shown on the lower left screen,

i.e. the scale has entered into the calibration mode.

Note: If the calibration unit, capacity, and resolution have been set, you may skip Steps II~IV and press

key to enter into Step V to perform zero point calibration.

Step II (Select Calibration Unit)

You may select calibration unit (kg, g, lb) by use of key.

Step III (Capacity Setting)

Press key and the flickering digit will shift to the right; press , key to set any value between

1-9; after setting, press key to enter into the next step.

Step IV (Resolution Setting)

Press key and the flickering digit will shift to the right; press , key to set any value between

1-9; after setting, press key to save and show the offset-value; press the weighing pan gently, if the

value changes, it’s normal.

Note: If you don’t want to perform calibration, just power off and the setting are completed.

Service Manual Indicator JIK-6 Page 10

Step V (Zero Point Calibration)

Press key to perform zero point calibration; when CAL on the lower left stops flickering, zero point

calibration is completed with CAL **kg shown.

Note: If the show value is very unstable, press key to enter into stb adjustment function, use key

to extend the range of stb (it is recommended to adjust one segment each time), after confirmation, press

key to save setting and the zero point calibration will be performed automatically.

Step VI (Single-point Calibration) Note: If to perform three-point calibration, skip this step.

Press key and the flickering digit will shift to the right; press , to adjust the value; input the

weight value to be calibrated, and put the correct weight onto the weighing pan, then press key to

save and confirm, once PASS is shown, take away the weight on the weighing pan and restart the machine

for normal use.

Step VII (Three-point Calibration)

Press key for 3 seconds until C-1 is shown at the lower left corner.

First Point C-1: Press key and the flickering digit will shift to the right; press , key to set

values; input the weight value to be calibrated, and put the correct weight onto the weighing pan, press

key to confirm and perform calibration.

Second Point C-2: Put the weight to be calibrated onto the weighing pan, the weight value will be shown

automatically on the screen; press key to confirm and perform calibration.

Third Point C-3: Put the weight to be calibrated onto the weighing pan, the weight value will be shown

automatically on the screen; press key to confirm and perform calibration. Once PASS is shown, take

away the weight on the weighing pan and restart the machine for normal use.

Recalibration: If any error occurs during calibration, press key to return to zero point calibration mode

and perform calibration according to the calibration procedures.

Note: The weight value in three-point calibration shall comply with C-1 < C-2 < C-3.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Vetek

Vetek

Vetek DYNA-LINK ERT Series Manual de usuario

Vetek

Vetek MO.DTR.526.R6 Manual de usuario

Vetek

Vetek EBW-2D Manual de usuario

Vetek

Vetek TI-1200 Manual de usuario

Vetek

Vetek PUE C/31 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario