Vestil CYL-D-1-PN Manual de usuario

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

CYL-D-1-PN &CYL-D-1-HR CYLINDER DOLLIES

INSTRUCTION MANUAL

Receiving instructions:

After delivery, IMMEDIATELY remove the packaging from the product in a manner that preserves

the packaging and maintains the orientation of the product in the packaging; then inspect the

product closely to determine whether it sustained damage during transport. If damage is

discovered during the inspection, immediately record a complete description of the

damage on the bill of lading. If the product is undamaged, discard the packaging.

NOTES:

1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location

where the product is used is exclusively the responsibility of the owner/end-user.

2) VESTIL is not liable for any injury or property damage that occurs as a consequence of failing

to apply either: a) Instructions in this manual; or b) Information provided on labels affixed to the

product. Neither is Vestil responsible for any consequential damages sustained as a result of

failing to exercise sound judgment while assembling, installing, using or maintaining this product.

Table of Contents

Hazard identification: explanation of signal words………………………………………………2

Safety Guidelines…………………………………………………………………………..……….2

FIG. 1: CYL-D-1-PN exploded parts diagram & bill of materials…………............................. 3

FIG. 2: CYL-D-1-HR exploded parts diagram & bill of materials……………………………… 4

Use instructions……………………………………………………………………………………..5

Inspections and Maintenance…………………………………………………………………….. 5

Label placement diagram…………………………………………………………………………. 6

Limited warranty……………………………………………………………………………………. 7

VESTIL MANUFACTURING CORP.

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703

Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868

Fax: (260) 665-1339

www.vestilmfg.com e-mail: [email protected]m

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

Hazard Identification--Explanation of SIGNAL WORDS

This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable

seriousness of those injuries, if the product is misused in the ways described. Other signal words call attention

to uses of the product likely cause property damage.

The signal words used appear below along with the meaning of each word:

Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS

INJURY. Use of this signal word is limited to the most extreme situations.

Identifies a hazardous situation which, if not avoided, COULD result in DEATH or

SERIOUS INJURY.

Indicates a hazardous situation which, if not avoided, COULD result in MINOR or

MODERATE injury.

Identifies practices likely to result in product/property damage, such as operation that might

damage the product.

Each person who assembles, installs, uses, or maintains this product should read the entire manual in

advance and fully understand the directions. If after reading the manual you do not understand an

instruction, ask your supervisor or employer for clarification, because failure to adhere to the directions

in this manual might result in serious personal injury.

SAFETY GUIDELINES

Vestil diligently strives to identify foreseeable hazards associated with the use of its products. However, no

manual can address every conceivable risk. The end-user ultimately is responsible for exercising sound

judgment at all times.

If this product is used improperly or carelessly, the operator and/or bystanders might sustain

serious personal injuries or even be killed. ALWAYS use the product properly:

Failure to read and understand the entire manual before assembling, installing, using or servicing the

product constitutes misuse.Read the manual to refresh your understanding of proper use and maintenance

procedures.

DO NOT exceed the maximum rated load.

Inspect the dolly before each use. Remove the dolly from service if the inspection reveals damage such as: 1)

cracked welds; 2) corrosion, extreme wear, or other condition that affects the ability of the product to support

applied weight; 3) significantly worn or cracked casters; 4) missing chains (1 chain for each of the semicircular

brackets). DO NOT use the product until it is restored to normal condition. ONLY use manufacturer-approved

replacement parts.

DO NOT use the dolly to transport any cylinder that does not seat securely in the semicircular brackets.

DO NOT transport a cylinder without using the bracket chains. Each time the dolly is used to transport a

cylinder, wrap the chains without slack around the cylinder. Secure the chains in the latch slots on the opposite

side of the brackets.

When transporting a cylinder up-or-downhill, always remain uphill to the cylinder.

DO NOT remove or obscure any label. All product labels must be readable and undamaged.

DO NOT modify the dolly in any way. Unauthorized modifications automatically void the limited warranty

(see p. 7) and might make the dolly unsafe to use.

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

FIG. 1:CYL-D-1-PN exploded parts diagram & bill of materials

Item

no. Part no. Description Quantity

1 16-132-199 10in. x 3½in. pneumatic wheel for 5/8in. axle 2

2 65026 5/64in. x 1 in. zinc-plated cotter pin 2

3 44-145-004

3/16in. x 24in. chain 2

4 11005 1/4in. – 20 UNC x 1in. HHCS #2 zinc-plated bolt 2

5 42016 1/4in. – 20 UNC x 1½in. U-bolt 2

6 36102 1/4in. – 20 zinc-plated hex nut 4

7 16-525-021 Handle weldment 1

8 16-112-019 Axle 1

9 16-514-139 Base and support gusset weldment 1

10 13-025-023 11/8in. (inner diameter) red handle grip 1

11 37018 1/4in. – 20 UNC zinc-plated nylock nut 2

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

FIG. 2:CYL-D-1-HR exploded parts diagram & bill of materials

Item

no. Part no. Description Quantity

1 65026 5/64in. x 1 in. zinc-plated cotter pin 2

2 44-145-004

3/16in. x 24in. chain 2

3 16-132-176 10in. x 2½in. hard rubber wheel (5/8in. axle) 2

4 11005 1/4in. – 20 UNC x 1in. HHCS #2 zinc-plated bolt 2

5 42016 1/4in. – 20 UNC x 1½in. U-bolt 2

6 36102 1/4in. – 20 zinc-plated hex nut 4

7 16-525-021 Handle weldment 1

8 16-514-139 Base and support gusset weldment 1

9 16-112-019 Axle 1

10 13-025-023 11/8in. (inner diameter) red handle grip 1

11 37018 1/4in. – 20 UNC zinc-plated nylock nut 2

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

Use Instructions:

1. Place the cylinder on the cart. Position the cylinder so that it seats firmly within the

(semicircular) cylinder brackets.

2. Wrap the chains around the cylinder with no slack.

3. Feed the free ends of the chains through the latch openings in the brackets, and seat a link

into the vertical slots.

Feed the ends of the chains

through the latch openings and

seat a link in the vertical slot.

Cylinder

bracket

Inspections and Maintenance:

Inspect the dolly periodically (at least every couple of months) to confirm normal condition. If the

inspection reveals problems, do not use the dolly until it is restored to normal condition.

Examine the dolly for cracked welds, metal fatigue, rust, and corrosion that affects the

structural integrity of the dolly.

Inspect the cylinder brackets. Each bracket should be solidly welded to the upright frame.

Check the hardware that fastens the handle to the frame. The connection should not be loose.

Tighten the fasteners if necessary.

Check the overall structure of the dolly. The frame should be rigid and square.

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

Label placement diagram:

The dolly is labeled as shown below.

Rev. 5/6/2013 CYL-D-1-PN, Manual.doc

LIMITED WARRANTY

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship

during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part

is covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service.

Who may request service?

Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an

authorized distributor AND Vestil has been fully paid.

What is an “original part”?

An original part is a part used to make the product as shipped to the warrantee.

What is a “proper request”?

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the

shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests

by any of the following methods:

Mail Fax Email

Vestil Manufacturing Corporation (260) 665-1339 [email protected]

2999 North Wayne Street, PO Box 507 Phone

Angola, IN 46703 (260) 665-7586

In the written request, list the parts believed to be defective and include the address where replacements should be

delivered.

What is covered under the warranty?

After Vestil receives your request for warranty service, an authorized representative will contact you to determine

whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the

entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the

following original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It

also covers defects in original parts that wear under normal usage conditions (“wearing parts”), such as bearings,

hoses, wheels, seals, brushes, and batteries.

How long is the warranty period?

The warranty period for original components is 90 days. The warranty period begins on the date when Vestil ships the

product to the warrantee. If the product was purchased from an authorized distributor, the period begins when the

distributor ships the product. Vestil may extend the warranty period for products shipped from authorized distributors

by up to 30 days to account for shipping time.

If a defective part is covered by the warranty, what will Vestil do to correct the problem?

Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact

you to discuss your claim.

What is not covered by the warranty?

1. Labor;

2. Freight;

3. Occurrence of any of the following, which automatically voids the warranty:

Product misuse;

Negligent operation or repair;

Corrosion or use in corrosive conditions;

Inadequate or improper maintenance;

Damage sustained during shipping;

Accidents involving the product;

Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written

authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive and/or

abnormal wear.

Do any other warranties apply to the product?

Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent

allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de elevación de Vestil

Vestil

Vestil AIR-1500-D Manual de usuario

Vestil

Vestil SE/HP Series Manual de usuario

Vestil

Vestil MFM-1300 Manual de usuario

Vestil

Vestil LLPW-CL-1560 Series Manual de usuario

Vestil

Vestil EHLTG Manual de usuario

Vestil

Vestil FTTM-2 Manual de instrucciones

Vestil

Vestil MH-V10 Manual de usuario

Vestil

Vestil LM-1T-8-24-HBE-TP Manual de usuario

Vestil

Vestil LLW-PAILD Series Manual de usuario

Vestil

Vestil CART-550-AS Manual de usuario

Vestil

Vestil HYD-5 Manual de usuario

Vestil

Vestil EPFC-CB-15 Manual de usuario

Vestil

Vestil Lifter-2 Manual de usuario

Vestil

Vestil DIE-2430-36 Manual de usuario

Vestil

Vestil CYL-M Manual de usuario

Vestil

Vestil CJIB Series Manual de usuario

Vestil

Vestil OLA-2-42 Manual de usuario

Vestil

Vestil HLD Series Manual de usuario

Vestil

Vestil LLH Series Manual de usuario

Vestil

Vestil EPC Series Manual de usuario

Vestil

Vestil AHS Manual de usuario

Vestil

Vestil EHLTD Series Manual de usuario

Vestil

Vestil FMDL Series Manual de usuario

Vestil

Vestil PMPS Series Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario