Vertiv Liebert APS Manual de usuario

590-1563-501A/SL-55016_REV1_3-17

LIEBERT® APS™

MODULE REPLACEMENT

Quick Installation Guide

These instructions apply to the

replacement or addition of the

following modules:

• Power module

• Battery module

• Charger module

• System control module

• System monitoring module

BATTERY, POWER, AND

CHARGER MODULE

REMOVAL

WARNING

Risk of heavy unit

falling over. Can cause equipment

damage, injury or death. Read all of the

instructions before attempting to move,

lift, remove packaging, or prepare the

unit for installation. The UPS represents

a tipping hazard.

Do not remove more than one module

at a time. Failure to do so may cause

unit to tip over and cause serious injury.

To locate a faulty module, remove the

bezel cover and look for an illuminated

yellow “fault” LED, which indicates a

faulty module.

If the removed bezel(s) have air filters,

replace them at this time.

NOTE

: If your system does not contain

a redundant module, place the UPS into

manual bypass mode before removing

modules to prevent accidental loss of

power to the connected equipment.

1. Removing the

module‑securing bracket

Use a Phillips-head screwdriver to

remove the fastener (if installed).

2. Releasing the lock lever

Pull out the lock lever slightly and

lift up, then wait a few seconds

before continuing.

3. Removing the module

from the cabinet bay

Slide the module out about

two-thirds of the way until it is

stopped by the safety catch.

Lift the module slightly and, while

supporting the module, slide it

completely out.

590-1563-501A/SL-55016_REV1_3-17

LIEBERT® APS™ MODULE REPLACEMENT

Quick Installation Guide

BATTERY, POWER, AND

CHARGER MODULE

INSTALLATION

4. Inserting a module

into a cabinet bay

Lift the module to the appropriate

bay, resting the end of the module

on the bay shelf.

NOTE

: Do not rest the module on

any plastic bezels. It could damage

the bezel.

NOTE

: Two battery modules must

be installed in the same row to

complete the battery string.

Slowly push the module in until

about one-third of the module is in

the bay.

Lift the module up, then continue

pushing until about 5 cm (2 in.) of

the module remains outside the bay,

then push it firmly and smoothly to

ensure that it is fully inserted.

5. Engaging the lock lever

Pull out the lock lever slightly

and press the lever down into the

bracket.

NOTE

: If the lever does not press

down smoothly, remove and reinstall

the module.

6. Attaching the

module‑securing bracket

Use a #2 Phillips-head screwdriver

to install the module-securing

bracket.

7. Replace the plastic bezel(s).

590-1563-501A/SL-55016_REV1_3-17

LIEBERT® APS™ MODULE REPLACEMENT

Quick Installation Guide

SYSTEM CONTROL OR

SYSTEM MONITORING

MODULE REMOVAL

CAUTION

When both a control

and monitoring module need replaced,

do not remove them at the same time.

If both are removed, the UPS shuts

down and power is removed from

the connected equipment unless

the system includes an external

maintenance-bypass system, and the

UPS is operating in maintenance-

bypass mode.

1. Remove the display bezel

and the LCD display.

Lay the display module on top

of the UPS.

2. Freeing the module

Use a Phillips-head screwdriver

to remove the screws from the

2 securing holes.

3. Releasing the lock lever

Pull out the lock lever slightly

and pull to the left, then wait a few

seconds before continuing.

4. Removing the module

Being sure to support the module,

slide it completely out of its control

bay.

NOTE

: These modules do not have

a safety catch because they are

lightweight.

SYSTEM CONTROL OR

SYSTEM MONITORING

MODULE INSTALLATION

5. Inserting a module

into a control bay

Push the module in until about 1

cm (1/2 in.) of the module remains

outside the bay, then push it firmly

and smoothly to ensure that it is

fully inserted.

6. Engaging the lock lever

Pull out the lock lever slightly and

press the lever to the right into

the bracket.

7. Re‑attaching the module

to the cabinet

Use a #2 Phillips-head screwdriver

to resecure the module.

8. Replace the LCD display

and the display bezel.

VertivCo.com |Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA

registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and disclaims all

liability, for damages resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.

590-1563-501A/SL-55016_REV1_3-17

Otros manuales de Unión Postal Universal de Vertiv

Vertiv

Vertiv LIEBERT PSI5 Series Instrucciones de instalación y mantenimiento

Vertiv

Vertiv Liebert GXT-MT+10KVA Manual de usuario

Vertiv

Vertiv Liebert NXL 500 Manual de usuario

Vertiv

Vertiv Liebert GXT5 Manual de usuario

Vertiv

Vertiv Liebert GXT MT+ EX 1-3 kVA Manual de usuario

Vertiv

Vertiv Liebert EXM MBC Manual de usuario

Vertiv

Vertiv Liebert PSI PS2200RT3-120 Manual de usuario

Vertiv

Vertiv Liebert GXT4-6000RTL630 Instrucciones de instalación y mantenimiento

Vertiv

Vertiv Liebert GXT5 Instrucciones de instalación y mantenimiento

Vertiv

Vertiv Liebert EXM series Manual de usuario

Vertiv

Vertiv Liebert GXT5-500LVRT2UXL Manual de usuario

Vertiv

Vertiv NetSure NSFP200 Manual de usuario

Vertiv

Vertiv Liebert EXM Manual de usuario

Vertiv

Vertiv Liebert Trinergy Cube Manual de instrucciones

Vertiv

Vertiv Liebert GXT5-8000HVRT5UXLN Manual de usuario

Vertiv

Vertiv Liebert GXT5 Manual de usuario

Vertiv

Vertiv Liebert NXL Manual de usuario

Vertiv

Vertiv Liebert PSA Manual de usuario

Vertiv

Vertiv Liebert EXS Manual de usuario

Vertiv

Vertiv Liebert GXT5 Manual de usuario

Vertiv

Vertiv Liebert EXM Manual de usuario

Vertiv

Vertiv Liebert EXL Manual de usuario

Vertiv

Vertiv EDGE-750IMT Manual de usuario

Vertiv

Vertiv Liebert EDGE Instrucciones de instalación y mantenimiento

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario