Vertiv DCE E42611 Manual de usuario

DCE™ Rack System

Installer/User Guide

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent section of

this manual to see if the issue can be resolved by following outlined procedures. For additional assistance,

visit https://www.VertivCo.com/en-us/support/

TABLE OF CONTENTS

1 Important Safety Instructions 5

2 What’s Included 7

3 Installation 9

3.1 Receiving, Unpacking, andRemovingtheDCERackfromthePallet 9

3.2 Loading Equipment 9

3.3 Operating Door Handle 9

3.4 Reversing the door handle 9

3.5 Door Removal and Attachment 11

3.6 Field-reversible Front and Rear Doors 12

3.7 Side Panel Removal 13

3.8 Top Panel Mounting 13

3.9 Top Panel Mounting for the E426112DR 14

3.10 Bottom Panel Mounting for the E426112DR 15

3.11 Casters and Leveling Feet 16

3.11.1 Leveling Feet Adjustment 20

3.12 Mounting Rail Adjustment 20

3.13 PDU/Cable-management Brackets 22

4 Optional Accessories 23

4.1 Vertical Cable Manager Kit: E846015 23

4.2 Horizontal Front-to-rear Cable Manager: E11015/E12015 25

4.3 Front-to-rear Cable Trough: E811015/E812015 25

4.4 Adjustable Ladder-rack Bracket: ELRB016 26

4.5 Overhead cable trough: E6016/7016/8016 28

4.6 Exhaust Chimney: E1832014/E3246014 29

4.7 Vertical-airflow Baffle with Brush Kit for800-mmWRack:E48801/E428014/E458014 29

4.8 Vertical Airflow Baffle with Brush Kit for700-mmWRack:E487014/E427014/E457014 31

4.9 Vertical-airflow Baffle withBrushKitandVerticalCableManager 32

4.10 Switch Kit for Side-to-side Cisco Switch for1000-mmWRack:E7009014/E7018014 33

4.11 Switch Kit for Side-to-side Cisco Switch

for800-mmWRack:E650304/E6506014/E9513014/E6513014 36

4.12 Baying Gasket Kit: E4013 38

4.13 Baying Kit: E9013 39

Vertiv | DCE Installer/User Guide | 3

Vertiv | DCE Installer/User Guide | 4

1 IMPORTANT SAFETY INSTRUCTIONS

Save These Instructions

This manual is provided to prevent service personnel from committing an act that results in the risk of fire,

electric shock, or injury to persons. Only trained service personnel should receive, unpack, and assemble

the DCE Racks. In addition, only trained service personnel should install equipment in racks.

Improper handling and use of the DCE Rack could result in equipment damage, serious injury, or possible

death.

WARNING: Only trained service personnel should be used to remove the rack from the pallet. Also, be

sure you have a sufficient number of service personnel. Do not attempt to move racks by yourself.

WARNING: All wiring and electrical circuits must be in compliance with National and Local electric

codes. Only ITE (Information Technology Equipment) bearing the safety compliance mark of a NRTL

should be installed inside the DCE Rack. NRTL compliance marks include UL®, C-UL®, CSA®, ETL®,

TUV®, and CE.

WARNING: Be sure to read and follow all individual manufacturer equipment manuals for safety and

installation instructions.

WARNING: Proper spacing is required when installing electrical equipment to avoid electrical shock.

Maintain minimum spacing between the accessories and components and the computer rack assembly

for safe operation of the equipment when installed in accordance with the National Electric Code

ANSI/NFPA 70-1999.

Vertiv | DCE Installer/User Guide | 5

Vertiv | DCE Installer/User Guide | 6

This page intentionally left blank.

2 WHAT’S INCLUDED

•DCE unit (assembled)

•Keys as needed (depending on configuration)

•(50) M6 cage nuts (3/8” square) and M6 screws

•Baying hardware

•Edge grommet

•This Installer/User Guide

This manual applies to the following pre-configured and applicable configured DCE racks:

PART NO. RU W (MM) D (MM)

E24611 24 600 1100

E42611 42 600 1100

E42612 42 600 1200

E426112DR 42 600 1100

E42711 42 700 1100

E42712 42 700 1200

E42811 42 800 1100

E42812 42 800 1200

E42112 42 1000 1200

E45611 45 600 1100

E45612 45 600 1200

E45711 45 700 1100

E45712 45 700 1200

E45811 45 800 1100

E45812 45 800 1200

E45112 45 1000 1200

E48611 48 600 1100

E48612 48 600 1200

E48711 48 700 1100

E48712 48 700 1200

E48811 48 800 1100

E48812 48 800 1200

E48112 48 1000 1200

DCE static weight capacity: 3000 lbs.

DCE dynamic weight capacity: 2500 lbs.

Vertiv | DCE Installer/User Guide | 7

Vertiv | DCE Installer/User Guide | 8

This page intentionally left blank.

3 INSTALLATION

3.1 Receiving, Unpacking, andRemovingtheDCERackfromthePallet

Inspect and report any damage before receiving. Unpack the rack by carefully removing the corrugated

carton and corners. Avoid damaging the rack when removing packaging.

WARNING: Only trained service personnel should be used to remove the rack from the pallet. Also, be

sure you have a sufficient number of service personnel. Do not attempt to move racks by yourself.

WARNING: Be careful when moving racks before installation. Sudden stops and starts, excessive

force, obstructed routes, and uneven floor surfaces may cause the rack to topple over.

3.2 Loading Equipment

WARNING: Only install equipment after the DCE Rack has been properly secured. Do not move the rack

assembly while loaded.

Once in place at the desired/intended location, deploy the leveling feet for maximum stability.

Rated or maximum-load capacity for the DCE Rack is 3000 pounds on the floor or on leveling glides.

To maintain a uniform distribution of the mechanical load in the DCE Rack, load the heaviest equipment

first, at the bottom of the DCE Rack and load the lighter units at the top.

3.3 Operating Door Handle

The door swing handles have been installed at the manufacturer. No additional assembly is required. To

operate the swing handle, lift up at the bottom of the handle then swing the handle to the right to open.

The handle must be kept in this position to close the door. Return the handle to the initial position and

use the key provided to lock the handle. The lock on the side panels will accept the same key.

The swing handles and doors are reversible. See "Reversing the door handle" below.

3.4 Reversing the door handle

1. Remove the Phillips-head bolt from the swing-handle retainer on the inside of the door.

2. Tilt the handle outward and lift up to remove it from the door.

3. Remove the Phillips-head cam retaining bolt, rotate the cam 180° and re-install cam retaining

bolt.

Vertiv | DCE Installer/User Guide | 9

4. After reversing the door, reinstall the swing handle by sliding downward into door and tilting

inward.

5. Re-install swing-handle retainer and Phillips head bolt.

Figure 3.1 Door handle components

ITEM DESCRIPTION

1 Phillips-head bolt

2 Phillips-head cam-retaining bolt

3 Cam

4 Retainer

Vertiv | DCE Installer/User Guide | 10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de Vertiv

Vertiv

Vertiv SmartAisle 03.029.214 Series Manual de usuario

Vertiv

Vertiv RMPSU Manual de usuario

Vertiv

Vertiv SmartAisle 12-21HE/U Manual de usuario

Vertiv

Vertiv NetSure 48BA1200-19 Manual de usuario

Vertiv

Vertiv Knurr DCM Manual de usuario

Vertiv

Vertiv SmartAisle-SwitchTube 19 Core 320mm 7-12HE/U Manual de usuario

Vertiv

Vertiv Avocent Manual de usuario

Vertiv

Vertiv MPX PRC Manual de usuario

Vertiv

Vertiv Knurr PowerTrans2 Manual de usuario

Vertiv

Vertiv 24BA1200-23 Manual de usuario

Vertiv

Vertiv Knurr DCM Heavy Duty Rack Manual de usuario

Vertiv

Vertiv Knurr Miracel 2 Manual de usuario

Vertiv

Vertiv KMMLED156 Instrucciones de instalación y mantenimiento

Vertiv

Vertiv MPH2 Manual de usuario

Vertiv

Vertiv NetSure 48BA1200-23 Manual de usuario

Vertiv

Vertiv KMMLED156 Manual de usuario

Vertiv

Vertiv DCF 48U Instrucciones de instalación y mantenimiento

Vertiv

Vertiv VP8641 Manual de usuario

Vertiv

Vertiv Smaract Manual de usuario

Vertiv

Vertiv Knurr DCM Manual de usuario

Vertiv

Vertiv VE Series Manual de usuario

Vertiv

Vertiv eSure 60017372 Manual de usuario

Vertiv

Vertiv MPE Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario