Vertex Standard VX-4000 Series Manual de usuario

VX-4000

OPERATING MANUAL

MANUAL DE OPERACIÓN

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

17210 Edwards Rd., Cerritos, CA 90703, U.S.A.

International Division

8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close

Winchester, Hampshire, SO23 0LB, U.K.

YAESU GERMANY GmbH

Am Kronberger Hang 2, D-65824 Schwalbach, Germany

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,

Kwun Tong, Kowloon, Hong Kong

POWER

Congratulations!

You now have at your fingertips a valuable communications tool - a two-way

radio! Rugged, reliable and easy to use, your radio will keep you in constant

touch with your colleagues for years to come, with negligible maintenance down time.

Please take a few minutes to read this manual carefully. The information presented here

will allow you to derive maximum performance from your radio. After reading it, keep

the manual handy for quick reference, in case questions arise later on.

We’re glad you joined the team. Call on us any time, because our business is

communications. Let us help you get your message across.

NOTICE

There are no user-serviceable points inside this transceiver. All service jobs must

be referred to your Authorized Service Center or Network Administrator.

Safety / Warning Information

WARNING - DO NOT operate the VX-4000L radio when someone (bystanders)

outside the vehicle is within 47 inches (1.2 meter) of the antenna.

Safety Training information:

Antennas used for this transmitter must not exceed an antenna gain of 0 dBd. The

radio must be used in vehicle-mount configurations with a maximum operating

duty factor not exceeding 50%, in typical Push-to-Talk configurations.

This radio is restricted to occupational use, work related operations only where the

radio operator must have the knowledge to control the exposure conditions of its

passengers and bystanders by maintaining the minimum separation distance of 47

inches (1.2 m).

Failure to observe these restrictions will result in exceeding the FCC RF exposure

limits.

Antenna Installation:

For rear deck trunk installation, the antenna must be located at least 47 inches (1.2

m) away from rear seat passengers in order to comply with the FCC RF exposure

requirements.

For roof top installation, the antenna must be placed in the center of the roof.

Page 1

VX-4000 Operating Manual

The VX-4000 Series are full-featured FM transceivers designed for flexible mobile and

base station business communications in the VHF Low-Band (60/25 Watts: program-

mable), VHF High-Band (50/25 Watts: programmable) and UHF (40/25 Watts: program-

mable) Land Mobile Bands. Each model is designed for reliable business communica-

tions in a wide variety of applications, with a wide range of operating capability provided

by its leading-edge design.

The 250-channels memories can each be programmed with a 8-character channel name. A

39-tone programmable CTCSS encoder/decoder is built in as standard.

Important channel frequency data is stored in EEPROM and flash memory on the CPU,

and is easily programmable by dealers using a personal computer and the VERTEX STAN-

DARD CT-71 Programming Cable and CE35 Software.

Special built-in features include:

rThe 250-channels memories can each be programmed with a 8-character channel

name.

rCTCSS (Continuous Tone Coded Squelch System);

rDCS (Digitally Coded Squelch);

rExtensive Selective Calling selections; and

rTwo sets of scanning channels, one set preset by the dealer and another which is

operator-selectable.

The pages which follow will detail the many advanced features provided on the VX-4000

transceiver. After reading this manual, you may wish to consult with your Network Ad-

ministrator regarding precise details of the configuration of this equipment for use in your

application.

POWER

Page 2

VX-4000 Operating Manual

Controls & Connectors

Front Panel

•PWR Button

Press the button to turn the transceiver ON and OFF.

‚TX Indicator

This lamp glows red when the radio is transmitting.

ƒBUSY Indicator

This lamp glows green when the channel is busy.

„Liquid Crystal Display

The display include an 8-character alpha-numeric section showing channel and group

names, status and identity information, and error messages. Additional indicators on

the display show priority channel assignments and scan include / exclude selection.

…

Button

Pressing these buttons changes the current group (and displayed group number or

name). Holding this button for more than 1/2 second causes the function to repeat.

†HOME Indicator

This lamp glows orange when incorrect position at the setting of CE35.

‡Programmable Function Button

This button can be set up for special applications, such as high/low power selection,

monitor, dimmer, talk-around, and call alert function, as determined by your network

requirements and programmed by your VERTEX STANDARD dealer.

The default function is set as Dimmer Button.

POWER

‚

„

…

‡

‰

†

•

Page 3

VX-4000 Operating Manual

ˆVOLUME Knob

This knob sets the volume of the receiver.

‰CHANNEL Selector Knob

This knob select the operating channel.

ŠProgrammable Function Button

This button can be set up for special applications, such as high/low power selection,

monitor, dimmer, talk-around, and call alert function, as determined by your network

requirements and programmed by your VERTEX STANDARD dealer.

Side Panel

Microphone Jack (It is on both sides.)

Connect the microphone plug to this jack.

Microphone Jack

Page 4

VX-4000 Operating Manual

REAR (Heatsink)

13.8-V DC Cable Pigtail w/Connector

The supplied DC power cable must be connected to this 2-pin connector. Use only

the supplied fused cable, extended if necessary, for power connection.

External Speaker Jack

An external loudspeaker may be connected to this 2-contact, 3.5-mm mini-phone

jack.

Caution: Do not connect this line to ground, and be certain that the speaker has

adequate capability to handle the audio output from the VX-4000.

Antenna Cable with Connector

The 50-ohm coaxial feedline to the antenna must be connected here using a type-M

(PL-259) plug.

DSUB 25-Pin Accessory Connector

External TX audio line input, PTT (Push To Talk), Squelch, and external RX audio

line output signal may be obtained from this connector for use with accessories such

as data transmission/reception modems, ets.

‚

•

„

Page 5

VX-4000 Operating Manual

Basic Operation of the Transceiver

Important! - Before turning on the radio the first time, confirm that the power connec-

tions have been made correctly and that a proper antenna is connected to the antenna jack.

Switching Power ON/OFF

Push the POWER switch turn on the radio. The display will become illuminated.

The radio will start up on the last channel used prior to shut-down during the previ-

ous operating session.

The display should show either a channel number or scan mode indicator (DSC,

USC, GDS, GUS, PDS, PUS, DDW or UDW). If “ERR” is displayed instead, the

transceiver has not yet been programmed with channel frequencies; switch off the

power and contact your network administrator or VERTEX STANDARD dealer. If

a scan mode indicator is displayed, you can press the SCAN button to display a

channel number, and then press either the UP (p) or DOWN (q) button to change

channels.

Setting the Volume

Turn the VOL knob clockwise to increase the volume, and counterclockwise to de-

crease it.

Transmitting

To transmit, wait until the “BUSY” indicator is off (the channel is not in use), and

press the PTT (Push-To-Talk) switch on the side of the microphone (the “TX” indi-

cator will appear or the “TX” indicator will glow red). While holding in the PTT

switch, speak across the face of the microphone in a clear, normal voice level, and

then release the PTT switch to receive.

Automatic Time-Out Timer

If the selected channel has been programmed for automatic time-out, you must limit

the length of each transmission. While transmitting, a beep will sound five seconds

before time-out. Another beep will sound just before the deadline; the “TX” indica-

tor will disappear and transmission will cease soon thereafter. To resume transmit-

ting, you must release the PTT and wait for the “penalty timer” to expire (if you press

the PTT before this timer expires, the timer restarts, and you will have to wait an-

other “penalty” period).

Selecting Groups and Channels

mPress the UP (p) or DOWN (q) button (repeatedly, if necessary) to select a dif-

ferent group of channels.

mTurn the CHANNEL selector knob to select a different channel within the current

group.

Page 6

VX-4000 Operating Manual

POWER

Advanced Operation

Programmable Function Button

The VX-4000 includes the seven Programmable Function Buttons. The Program-

mable Function Button functions can be customized, via programming by your VER-

TEX STANDARD dealer, to meet your communications/network requirements. Some

features may require the purchase and installation of opetional internal accessories. The

possible Programmable Function Button programming features are illustrated at the

below, and their functions are explained on page ?.

For further details, contact your VERTEX STANDARD dealer. For future reference, check

the box next to each function that has been assigned to the Programmable Function

Button on your particular radio, and keep it handy.

Functions Programmable Function Button

None

Call/Reset

Talk-Around

Noise Blanker

Alpha Numeric

DIM

EMG

Home

MONI

GRP UP/DWN

CH UP/DWN

SCAN

SP*

SQL

Encryption**

* requires YSK-4000

** requires Encryption Unit

Page 7

VX-4000 Operating Manual

Scanning Modes

There are eight scanning modes, described in the list below. Each channel can be

independently enabled or disabled for scanning; only channels selected for scanning

within the enabled group are scanned. Also, as mentioned before, each group can

have up to two priority channels which are scanned more often than the non-priority

channels.

The SCAN modes and their corresponding displays are as follows:

Display Scanning Function

DSC Dealer Scan (only within the current group)

USC User Scan: only user-selected channels (only within the current group)

GDS Group Dealer Scan: scan all Dealer-selected channels in all groups

GUS Group User Scan: scan all User-selected channels in all groups

PDS Priority Dealer Scan: DSC plus priority channel(s)

PUS Priority User Scan: USC plus user priority channel(s)

DDW Dealer Dual Watch: Monitor one channel and priority channel(s)

UDW User Dual Watch: Monitor User-selected channel and priority channel(s)

Scanning Operation

With the microphone in its hanger, press the assigned Programmable Function

Button of the “SCAN” momentarily to activate scanning. Typically, “DSC” will

initially appear on the display, indicating Dealer Channel Scan as the scanning mode.

If you wish to change to one of the modes described in the list above, press the

assigned Programmable Function Button of the “SEL” button repeatedly until

that mode appears on the display.

If you pick up the microphone while no signal is being received, operation will shift

to a particular channel. Which channel that will be depends on which of the follow-

ing options the dealer has programmed for off-hook channel selection:

Scan Start Channel

Lifting the microphone causes operation to revert to the group and channel last se-

lected before scanning started or resumed.

Priority Revert

Lifting the microphone activates the Priority 1 channel in the current group. If no

channel is assigned level 1 priority, operation will be on the Priority 2 channel. If no

priority channels have been assigned, operation reverts to the Scan Start Channel.

Last Busy

Lifting the microphone causes operation to revert to the group and channel where

activity was last detected. If no activity was detected since turning on the radio,

operation reverts to the Scan Start Channel.

Page 8

VX-4000 Operating Manual

How to Select Channels to be Scanned

If your radio has been configured by your Dealer to allow you, the operator, to make

changes to the list of channels to be scanned, you can make these changes by following

this simple process:

ÀPress and hold in the SEL button; while holding this button in, press the POWER

button to turn the radio on. You may now release the ?? button.

ÁPress the ?? button, as necessary, until the Memory Group and Memory Channel

numbers will appear in small characters in the right side of the display area.

ÂYou may now push the ?? key momentarily as many times as necessary to choose

the Memory Group within which you wish to make changes to the channel scan

list. Once you have selected the desired Memory Group, you may use the UP (p)

or DOWN (q) button to choose a particular channel within the current group.

Pressing the ?? button will change the scanning status of the selected channel.

If you are adding the channel to those you wish to scan, pressing the ?? button

causes a “U” appear on the display, indicating that the channel has been added to

the User Scan List. If you are deleting the channel from the User Scan List (the

channel's data itself will not be deleted; the channel just will not be scanned), the

“U” will disappear.

ÃRepeat step 3 for each channel you wish to enable or disable for scanning.

ÄWhen you are done making changes to the channels you wish to scan, press and

hold in the ?? button for more than 1.5 second. Operation will return to its normal

status, and the display will revert to its previous appearance.

Otros manuales para VX-4000 Series

Tabla de contenidos

Otros manuales de Transceptor de Vertex Standard

Vertex Standard

Vertex Standard VX-1400 Manual de usuario

Vertex Standard

Vertex Standard VXA-710 SPIRIT Manual de usuario

Vertex Standard

Vertex Standard VX-5500U Manual de usuario

Vertex Standard

Vertex Standard VX-556 Manual de usuario

Vertex Standard

Vertex Standard FT-2900R Manual de usuario

Vertex Standard

Vertex Standard VX-4000V Manual de usuario

Vertex Standard

Vertex Standard VX-160EU Manual de usuario

Vertex Standard

Vertex Standard VX-160U Manual de usuario

Vertex Standard

Vertex Standard HX100 Manual de usuario

Vertex Standard

Vertex Standard FT-100 Manual

Vertex Standard

Vertex Standard Spirit VXA-700 Manual de usuario

Vertex Standard

Vertex Standard VX-2200(LTR) Series Manual de usuario

Vertex Standard

Vertex Standard VX-350 series Manual de usuario

Vertex Standard

Vertex Standard VX-6000L Manual de usuario

Vertex Standard

Vertex Standard VX-6000L Manual de usuario

Vertex Standard

Vertex Standard VX-820ATEX Manual de usuario

Vertex Standard

Vertex Standard GX1100S Manual de usuario

Vertex Standard

Vertex Standard GX2360S Manual de usuario

Vertex Standard

Vertex Standard VX-3R Manual de usuario

Vertex Standard

Vertex Standard VX-230 Series Manual de usuario

Vertex Standard

Vertex Standard VX-6000V Manual de usuario

Vertex Standard

Vertex Standard VX-230 Series Manual de usuario

Vertex Standard

Vertex Standard VX-4600 Series Manual de usuario

Vertex Standard

Vertex Standard VX-4200 Series Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario