Vermeer SC362 Manual de usuario
SC362 Stump Cutter
SC362_o1_00
Serial No. 101 -
Order No. 105400CT8
Cabled Assembly Order No. 163708565
Operator’s
Manual
Introduction SC362 Stump Cutter
Introduction
This manual explains the proper operation of your machine. Study and understand these instructions thoroughly before operating or
maintaining the machine. Failure to do so could result in personal injury or equipment damage. Consult your Vermeer dealer if you
do not understand the instructions in this manual, or need additional information.
The instructions, illustrations, and specifications in this manual are based on the latest information available at time of publication.
Your machine may have product improvements and features not yet contained in this manual.
Vermeer Corporation reserves the right to make changes at any time without notice or obligation.
Operation instructions are included in the two Operator’s Manuals provided with the machine. The tethered (cabled)
manual must remain attached to the machine for ready reference. Store it in the manual storage box when not in use.
Lubrication and maintenance procedures are in the Maintenance Manual provided with the machine. Refer to it for all
lubrication and maintenance procedures.
Additional copies of the manuals, and Operations and Safety video, are available from your dealer. Reorder numbers are listed on the
front covers of the manuals and on the video.
Copies of this manual are available in Spanish from your dealer. Other languages may also be available.
Se dispone de ejemplares de este manual en español.
NOTICE TO OWNER
You are requested to notify Vermeer Corporation when you have purchased a used Vermeer machine. Notify the Customer Data
Department by telephone: 800-829-0051 or 641-628-3141; email: customerdata@vermeer.com; internet: www.vermeer.com or
www.vermeerag.com; or letter: Customer Data Dept., Vermeer Corporation, PO Box 200, Pella IA 50219 USA. Upon request, an
owner of a used Vermeer machine will receive one free set of Operator’s, Maintenance and Parts manuals.
SC362 Stump Cutter Introduction
Orientation: Forward travel of this machine is away from the cutter wheel. Right and left sides are determined when facing in the
direction of forward travel.
TRADEMARKS
VERMEER, VERMEER Logo, AUTOSWEEP, and YELLOW JACKET are trademarks of Vermeer Manufacturing Company.
VANGUARD and BRIGGS & STRATTON are trademarks of Briggs and Stratton Corporation.
FORWARD
FORWARDDIRECTION
FORWARDDIRECTION
Introduction SC362 Stump Cutter
VERMEER NEW INDUSTRIAL EQUIPMENT LIMITED WARRANTY
(EFFECTIVE AUGUST 1, 2013) WARRANTY PERIOD: 12 Months / 1000 Hours
Vermeer Corporation (hereinafter “Vermeer”) warrants each new Industrial product of Vermeer’s manufacture to be free from defects
in material and workmanship, under normal use and service for one (1) full year after initial purchase/retail sale or 1000 operating
hours, whichever occurs first. This Limited Warranty shall apply only to complete machines of Vermeer’s manufacture, parts are
covered by a separate Limited Warranty. EQUIPMENT AND ACCESSORIES NOT OF VERMEER’S MANUFACTURE ARE
WARRANTED ONLY TO THE EXTENT OF THE ORIGINAL MANUFACTURER’S WARRANTY AND SUBJECT TO
THEIR ALLOWANCE TO VERMEER ONLY IF FOUND DEFECTIVE BY SUCH MANUFACTURER.
EXTENDED WARRANTY OPTIONS ARE AVAILABLE FOR PURCHASE WARRANTY TERMS During the Limited
Warranty period specified above, any defect in material or workmanship in any warranted item of Vermeer Industrial Equipment not
excluded below shall be repaired or replaced at Vermeer’s option without charge by any authorized independent Vermeer dealer. The
warranty repair or replacement must be made by a Vermeer independent authorized dealer at the dealer’s location. Vermeer will pay
for replacement parts and such authorized dealer’s labor in accordance with Vermeer’s labor reimbursement policy. Vermeer reserves
the right to supply remanufactured replacement parts as it deems appropriate.
RETAIL PURCHASER RESPONSIBILITY: This Limited Warranty requires proper maintenance and periodic inspections of the
Industrial Equipment as indicated in the Operator’s/Maintenance Manual furnished with each new Industrial Equipment. The cost
of routine or required maintenance and services is the responsibility of the retail purchaser. The retail purchaser is required to keep
documented evidence that these services were performed. This Vermeer New Industrial Equipment Limited Warranty may be
subject to cancellation if the above requirements are not performed. Vermeer Industrial Equipment with known failed or defective
parts must be immediately removed from service.
SC362 Stump Cutter Introduction
EXCLUSIONS AND LIMITATIONS
The warranties contained herein shall NOT APPLY TO:
1) Any defect which was caused (in Vermeer’s sole judgment) by other than normal use and service of the Industrial Equipment,
or by any of the following; (i) accident (ii) misuse or negligence (iii) overloading (iv) lack of reasonable and proper maintenance
(v) improper repair or installation (vi) unsuitable storage (vii) non-Vermeer approved alteration or modification (viii) natural
calamities (ix) vandalism (x) parts or accessories installed on Industrial Equipment which were not manufactured or installed
by Vermeer authorized dealers (xi) the elements (xii) collision or other accident.
(2) Any Industrial Equipment whose identification numbers or marks have been altered or removed or whose hour meter has
been altered or tampered with.
(3) Any Industrial Equipment which any of the required or recommended periodic inspection or services have been performed
using parts not manufactured or supplied by Vermeer or meeting Vermeer Specifications including, but without limitation,
engine tune-up parts, engine oil filters, air filters, hydraulic oil filters, and fuel filters.
(4) New Industrial Equipment delivered to the retail purchaser in which the equipment/warranty registration has not been
completed and returned to Vermeer within ten (10) days from the date of purchase.
(5) Any defect which was caused (in Vermeer’s sole judgment) by operation of the Industrial Equipment not abiding by standard
operating procedures outlined in the Operator’s Manual.
(6) Engine, battery, and tire Limited Warranties and support are the responsibility of the respective product’s manufacturer.
(7) Transportation costs, if any, of transporting to the Vermeer dealer. Freight costs, if any, of transporting replacement parts to
the Vermeer dealer.
(8) The travel time of the Vermeer dealer’s service personnel to make a repair on the retail purchaser’s site or other location
(9) In no event shall Vermeer’s liability exceed the purchase price of the product,
10) Vermeer shall not be liable to any person under any circumstances for any incidental or consequential damages (including but
not limited to, loss of profits, out of service time) occurring for any reason at any time.
(11) Diagnostic and overtime labor premiums are not covered under this Limited Warranty Policy. Oils and fluids are not covered
under this Limited Warranty.
Introduction SC362 Stump Cutter
(12) Depreciation damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow operating
instructions, misuse, lack of proper protection during storage.
(13) Accessory systems and electronics not of Vermeer’s manufacture are warranted only to the extent of such manufacturer’s
respective Limited Warranty if any.
(14) Down hole toolage is not covered under this warranty.
(15) Wear items which are listed by product group below:
ENVIRONMENTAL:Bearing Seals, Bearings, Belts, Brake Pads, Bolts/Torqued Parts, Chain, Clutches, Clutch Components,
Curtains, Cutter Wheels, Discharge Conveyor Belts, Fuel Filters, Hammers, Hoses, Infeed Conveyor Belts, Infeed Conveyor Chains,
Knives, Oil Filters, Pockets, Rods, Rollers, Rotor Plates, Screens, Service Items, Shear Bar/Bedknife, Sprockets, Teeth, Wear Blocks,
Wear Strips, Tips, Tip Mounts, Track Chain, Track Rollers, Rubber Tracks, Rubber Grouser Bars, Rubber Track Bands, Track
Sprockets, Track Pads, Winch Cable, Windshield Wiper Parts, Lights, Antenna.
TRACK:Base Plates, Boom Wear Items, Buckets, Cable Fingers, Conveyor Belts, Clutches, Cups, Digging Chain, Digging Rims,
Drums, End Idler, Flashings, Pins and Bushings, Pivot Rings, Plastic Wear Strips, Rooter Bands, Scraper Knives, Sprockets, Teeth,
Track Chain, Track Rollers, Trench Cleaner (Crumber), Trip Cleaners, Truck Rollers, Wear Plates.
TRENCHLESS:Brushes, Clamping Vise Parts, Dies, Drive Chuck, Earth Stakes, Fan Belts, Jaws, Leaf Chain, Lights On Light
Kits, Packing Assemblies, Rod, Rod Loader Parts, Rollers, Tooling, Track Chain, Track Guides, Track Idlers, Track Pads, Track
Sprockets, Valve Seats, Wear Bars, Wear Blocks, Water Hoses, Water Swivels, Wear Bars.
UTILITY PRODUCTS: Augers, Belts, Bearings, Booms, Brake Pads, Bucket, Bushings, Chains, Clutches, Conveyor Belts, End
Rollers, Flashings, Pins, Pivot Rings, Plow Blades, Rubber Shielding, Sprockets, Teeth, Tires, Track Chain, Track Idlers, Track
Sprockets, Trench Cleaner (Crumber).
PARTS WARRANTY:
Parts replaced in the warranty period will receive the balance of the first year New Industrial Equipment Limited Warranty, during
the first (12) months or 1000 hours, whichever comes first. Replacement parts after the original machine warranty, are warranted to
be free from defects of material for ninety (90) days or the part will be repaired or replaced, without labor coverage for removal and
reinstallation.
SC362 Stump Cutter Introduction
EXCLUSIONS OF WARRANTIES: EXCEPT FOR THE WARRANTIES EXPRESSLY AND SPECIFICALLY MADE
HEREIN, VERMEER MAKES NO OTHER WARRANTIES, AND ANY POSSIBLE LIABILITY OF VERMEER
HEREINUNDER IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING, BUT
NOT LIMITED TO, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
VERMEER RESERVES THE RIGHT TO MODIFY, ALTER AND IMPROVE ANY PRODUCT WITHOUT INCURRING ANY
OBLIGATION TO REPLACE ANY PRODUCT PREVIOUSLY SOLD WITH SUCH MODIFICATION. NO PERSON IS
AUTHORIZED TO GIVE ANY OTHER WARRANTY, OR TO ASSUME ANY ADDITIONAL OBLIGATION ON VERMEER’S
BEHALF.
NO DEALER WARRANTY. The selling dealer makes no warranty of its own and the dealer has no authority to make any
representation or promise on behalf of Vermeer or to modify the terms or limitations of this warranty in any way.
ELECTRONIC SIGNATURES. Each of the parties hereto expressly agrees to conduct transactions by electronic means.
Accordingly, the parties agree and intend that all electronic transmissions including, without limitation, electronic signatures, shall
be considered equivalent to an original writing as provided under Iowa law, as it may be amended from time to time.
MANUFACTURED BY:
VERMEER CORPORATION
Pella, Iowa 50219 USA
This page intentionally left blank.
SC362 Stump Cutter Receiving and Delivery Report i
Receiving and Delivery Report
DEALER PREP
Check or perform the following:
___ Check machine for shortage or damage in transit.
Engine
___ Check oil level of the engine, with engine level.
___ Check condition of the air cleaner.
___ Check electrolyte level of the battery.
___ Check engine for proper operation.
Hydraulics
___ Check level of the hydraulic fluid.
___ Check control levers for proper operation.
___ Check all hydraulic components for leaks or damage.
General
___ Check drive belts for proper tension.
___ Check ground drive chain for proper tension.
___ Check all shields for installation and condition.
___ Check machine for proper lubrication.
___ Check condition of all safety signs and decals.
___ Check all phases of operation.
___ Check for loose hardware.
ii Receiving and Delivery Report SC362 Stump Cutter
___ Check protective curtains for installation and condition.
___ Check tires for proper air pressure: 50 psi (340 kPa)
___ Check cutter wheel Yellow Jacket pocket bolts for proper torque: 200–215 ft-lb (271–291 Nm).
___ Check that the neutral start function operates properly
.
___ Check that Operator Presence system and indicator lights operate properly.
Tabla de contenidos
Otros manuales de Cortador de Vermeer
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
