Veris Industries H5004 Manual de usuario

6%2)3).$5342)%3

CURRENT MONITORING INSTALLATION GUIDE

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Current Sensing Four-Point

Remote Status Panel/Sensor Kit

Installer’s Speciﬁcations

Temperature Range -15° to 85°C (5° to 185°F)

Humidity Range 0 - 95% non-condensing

Trip Point Adjustable

Hysteresis 10% Typical

Output Type Dry Contact, reed relay, N.O.

Output Rating 200mA@30VAC/DC

50mA@120VAC

No. of Points Accepted 1-4 sensors (H5800 solid core)

Supply Voltage 24VAC/DC

Supply Current 50mA max.

Housing NEMA 1

H5800 Current Sensor:

Amperage Ratings 1 to 100A continuous

Wiring Up to 1000’ from panel, 2 wire, 22 AWG twisted pair

All outputs and adjustments are per point.

Do not use the LED status indicators as evidence.

)";"3%0'&-&$53*$4)0$,&91-04*0/03"3$'-"4)

t 'PMMPXTBGFFMFDUSJDBMXPSLQSBDUJDFT

4FF/'1"&JOUIF64"PSBQQMJDBCMFMPDBMDPEFT

t 5IJTFRVJQNFOUNVTUPOMZCFJOTUBMMFEBOETFSWJDFECZRVBMJmFEFMFDUSJDBMQFSTPOOFM

t 3FBEVOEFSTUBOEBOEGPMMPXUIFJOTUSVDUJPOTCFGPSFJOTUBMMJOHUIJTQSPEVDU

t 5VSOPõBMMQPXFSTVQQMZJOHFRVJQNFOUCFGPSFXPSLJOHPOPSJOTJEFUIFFRVJQNFOU

t 6TFBQSPQFSMZSBUFEWPMUBHFTFOTJOHEFWJDFUPDPOmSNQPXFSJTPõ

%0/05%&1&/%0/5)*4130%6$5'0370-5"(&*/%*$"5*0/

t 0OMZJOTUBMMUIJTQSPEVDUPOJOTVMBUFEDPOEVDUPST

'BJMVSFUPGPMMPXUIFTFJOTUSVDUJPOTXJMMSFTVMUJOEFBUIPSTFSJPVTJOKVSZ

%"/(&3

Wiring ExamplE

H5004/H5004C 5004/5004C

DimEnsions

/05*$&

t 5IJTQSPEVDUJTOPUJOUFOEFEGPSMJGFPSTBGFUZBQQMJDBUJPOT

t %POPUJOTUBMMUIJTQSPEVDUJOIB[BSEPVTPSDMBTTJmFEMPDBUJPOT

t 5IFJOTUBMMFSJTSFTQPOTJCMFGPSDPOGPSNBODFUPBMMBQQMJDBCMFDPEFT

t .PVOUUIJTQSPEVDUJOTJEFBTVJUBCMFmSFBOEFMFDUSJDBMFODMPTVSF

quick install

Disconnect and lock out power to the conductor to be monitored.1.

Install the Remote Status Panel near the controller. Wire the supply voltage2.

terminal to 24VAC/DC power source.

Slide the conductors to be monitored through the sensing irises of the current3.

transducers (up to 4 transducers per Panel). See Notes (page 2) for currents under

1 Amp or above 100 Amp. Note: Transducers may be located up to 1000 feet from

the Remote Status Panel.

Wire the output connections between the sensors and the Remote Status Panel.4.

See Wiring section (page 2) for details. Sensors are polarity sensitive.

Adjust the amperage setpoint at which the Panel output will trip. Turn clockwise5.

to increase.

Reconnect power.6.

Motor

Control Center

Digital Control

Fan/pump #1

Hawkeye 5000

Adjustable Current

Status Sensor

Fan/pump #2

Starters H5800 Mini-Sensor

Digital

Status

Inputs

4.2”

(105 mm)

2.75”

(70 mm)

Ø = 0.7”

(18 mm)

1.8”

(46 mm)

2.5”

(64 mm)

2.3”

(58 mm)

0.9”

(22 mm)

H5004

H5004C

proDuct iDEntification

Model Description

H5004 Remote Status Panel

H5004C Remote Status Panel Kit (includes four H5800 current sensors)

H5800 Current Sensors, sold separately

6%2)3).$5342)%3

INSTALLATION GUIDE

H5004/H5004C

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

opEration

The H5004 Remote Status Panel is capable of simultaneously tracking the output

from up to four separate current transducers and displaying the operation status of

those conductors in one convenient location. LEDs indicators on the Panel’s face show

the active status of each conductor. The H5004C Panel Kit includes four H5800 mini

solid-core transducers, with a range of 1 to 100A. These sensors can be installed up

to 1000 feet from the H5004 Panel. The H5004 requires 24VAC/DC external power to

generate its output.

notEs

For load currents less than sensor minimum rating:

Wrap the monitored conductor through the center hole and around the sensor body

to produce multiple turns through the "window." This increases the current measured

by the transducer.

Controller must be programmed to account for

the extra turns. e.g., if four turns pass through

the sensor (as shown) the normal controller

reading must be divided by 4.

< 1A (sensor min.)

0.5A

DANGER: 5A CTs can present hazardous voltages.

Install CTs in accordance with manufacturer's instructions.

Terminate the CT secondary before applying current.

H681x-5A CT

240A

300A:5A

> 100A (H5800 max.)

For load currents greater than sensor maximum rating:

Use a 5 Amp (H681x series) Current Transformer (CT) as shown.

CAUTION

RISK OF EQUIPMENT DAMAGE

t %FSBUFUIFQSPEVDUTNBYJNVNDVSSFOUGPSUIFOVNCFSPGUVSOT

UISPVHIUIFTFOTJOHXJOEPXVTJOHUIFGPMMPXJOHGPSNVMB

3BUFE.BY"NQT/VNCFSPG5VSOT.BYNPOJUPSFE"NQT

FH"5VSOT"NQTNBYJONPOJUPSFEDPOEVDUPS

t 'BJMVSFUPGPMMPXUIFTFJOTUSVDUJPOTDBOSFTVMUJOPWFSIFBUJOH

BOEQFSNBOFOUFRVJQNFOUEBNBHF

Wiring

Power

24 VAC/DC

Power Supply

24 VAC/DC IN

Sensor 1 Status 1 Output 1

Output 2

Output 3

Output 4

Status 2

Status 3

Status 4

Sensor 2

Sensor 3

Sensor 4

Use Veris H5800 current sensors only. H5004 Remote Status Panel Building Control Panel

Digital

Inputs

Power Input

troublEshooting

Problem Solution

No reading at controller · Check that + and - polarity is observed in

the wiring.

calibration

Before beginning calibration, establish normal load conditions.

A. To monitor under-current (belt loss, coupling shear, status):

OK!

1. Turn setpoint screw counterclockwise

until Status LED turns on.

2. Slowly turn the screw clockwise to ﬁnd

the point at which the Status LED just turns

oﬀ.

Turn the screw an additional ¼ turn

counter-clockwise from the position

determined in step 2 above. The Status LED

should be ON. The sensor is now calibrated to

indicate amperage ﬂow below normal levels.

B. To monitor over-current (mechanical problems, seized impeller):

OK!

45"564

OK!

45"564



4FUQPJOU



4FUQPJOU

Setpoint Status

STOP

The sensor threshold is now balanced at the amperage level being

monitored. Proceed to A or B below.

Turn the screw an additional ¼ turn clockwise

from the position determined in step 2 above. If

the current exceeds this trip point, the contact

will close.

H5800 sensor

Este manual sirve para los siguientes modelos

Otros manuales de Instrumento de medición de Veris Industries

Veris Industries

Veris Industries E50H2A Manual de usuario

Veris Industries

Veris Industries E31A004 Manual de usuario

Veris Industries

Veris Industries H8030 Manual de usuario

Veris Industries

Veris Industries E50H Series Manual de usuario

Veris Industries

Veris Industries E54C3C Manual de usuario

Veris Industries

Veris Industries E50 Series Manual de usuario

Veris Industries

Veris Industries E30C184 Manual de usuario

Veris Industries

Veris Industries E31 Series Manual de usuario

Veris Industries

Veris Industries E50F2A Manual de usuario

Veris Industries

Veris Industries E31E Series Manual de usuario

Veris Industries

Veris Industries E50C1A Manual de usuario

Veris Industries

Veris Industries E50C1 Manual de usuario

Veris Industries

Veris Industries Hawkeye H749 Manual de usuario

Veris Industries

Veris Industries ENERCEPT H8035 Manual de usuario

Veris Industries

Veris Industries H8150-1600-4-3 Manual de usuario

Veris Industries

Veris Industries E50C2 Manual de usuario

Veris Industries

Veris Industries H81 Series Manual de usuario

Veris Industries

Veris Industries E51H2 Manual de usuario

Veris Industries

Veris Industries Hawkeye H949 Manual de usuario

Veris Industries

Veris Industries E51C2A Manual de usuario

Veris Industries

Veris Industries E51H2A Manual de usuario

Veris Industries

Veris Industries HW2 Series Manual de usuario

Veris Industries

Veris Industries E50B1 Manual de usuario

Veris Industries

Veris Industries E30 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario