Veris Industries G Series Manual de usuario
VERIS INDUSTRIES ™
environmental SenSorS inStallation GUiDe
Z202025-0N PAGE 1 ©2008 Veris Industries USA 800.354.8556 or +1(0)503.598.4564 / suppor[email protected] 09091
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Carbon Monoxide Transmitter
and Fan Controller
Installer’s Specifications
Sensor Digitally proled Metal Oxide Semiconductor (MOS)
Sensor Life 5-year expected sensor element life, replaceable
Supply Power 15-30VDC, 24VAC, 250mA
Detection Range 0 to 200 ppm
Analog Output User selectable 100 ppm F.S. or 200ppm F.S.
Relay Setpoint 25ppm
Relay Output N.O. Form A (SPST) 8A@30VAC/VDC; (Use with N.C. contactor)
High Limit Setpoint 100ppm for 30 minutes
High Limit Alarm Audible, 85dB, resets below 100ppm (solid-state contact for A ver)
LED Indicators Normal=Green LED; Call for ventilation = Red LED;
High-limit alarm = Flashing Red LED;
Sensor life has expired = Flashing Green LED
Operating Environment -20° to 50°C (-4°to 122°F); 0 to 90% RH non-condensing
Coverage 5000 sq ft typical
G SerieS G SerieS
Dimensions
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• Read and understand the instructions before installing
this product.
• Turn off all power supplying equipment before working on it.
• The installer is responsible for conformance to all applicable codes.
ProDuct iDentification
quick install
Lock out all power supplies prior to installation
Select a location for the sensor in a secure area where it will be accessible only to
qualied service personnel The G Series sensor should be installed centrally in the
parking structure near the main trac paths but away from outside air vents and
excessive drafts Mount the unit securely to a wall or column at a height of about
ft m from the oor
Connect wiring as shown in the Wiring Diagram
Apply power to the unit A green LED on the circuit board indicates proper
operation of the power supply
Note: Coverage is NOT dependant on the sensor Coverage is a function of the building structure
and air ow patterns A minimum of one sensor for sq ft is recommended Wide open areas
where the air is well mixed may require a few sensors
2.4"
(55 mm)
2.5"
(63 mm)
0.9" dia.
(22 mm)
4.5”
(114 mm) 4"
(102 mm)
5.0"
(127 mm)
2.25"
(57 mm)
G
D = Duct mount
W = Wall mount
Enclosure Auxiliary Alarm OutputOutput
A = Auxiliary Contact
X = None
= StandardV = Field-selectable,
0-5/0-10VDC
M =4-20mA
R = Relay only
S
US or EU
VERIS INDUSTRIES ™
inStallation GUiDe
G SerieS
Z202025-0N PAGE 2 ©2008 Veris Industries USA 800.354.8556 or +1(0)503.598.4564 / suppor[email protected] 09091
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
oPeration
The G Series carbon monoxide detectors measure CO levels and signal control systems
to provide an inlet of fresh air optimal for the space at a given time. The G Series
devices are equipped with a relay contact that closes when CO level is below 25ppm
and opens when the CO level is above 25ppm (when used with a normally closed
contactor). Removal of the sensor, interruption of power, or cut wires cause the relay
circuit to open and start the fan. Minimum relay cycle time is 3 minutes to prevent
fan short-cycling.
Audible Alarm: 85dB alarm sounds if CO level rises above 100ppm for 30 minutes.
LED Indicators:
LED Description
Green Normal operation
Flashing Green Sensor life has expired
Red Call for ventilation
Flashing Red CO level above ppm for minutes
wiring Diagram
-+
-+
0-10V/0-5V
or
4-20mA
DDC
SYSTEM
V in
COMM
SENSOR
CONTACTOR
POWER
FAN
POWER
N.C.
CONTACTOR
ALARM
N.O.
OUT
SENSOR DETAIL
Common
Out 0-5V/10V or 4-20mA
IN V+ 15-30VDC, 24VAC
N.O. Relay
N.O. Relay
OUTPUT
10V 5V
PPM
100
200
troubleshooting
Problem Solution
mA output does not function
Output is half or twice what is
expected
voltage output scale
Output is inaccurate or unstable
service
For any service or installation consult qualied service personnel To assure
continued reliable operation the sensor module should be replaced every ve years
with a Veris Industries CO sensor replacement module
Replacement instructions:
Disconnect power from the unit
Carefully remove the old sensor module
Install the new module rmly into the socket
Reconnect power to the unit
The replacement sensor requires hours after initial power application to
The sensor module is factory calibrated No eld calibration is required or possible
Verify proper operation by observing LED indicators
Otros manuales de Controladores de Veris Industries
