Vent-Axia VA 150 A Instrucciones de montaje

READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS

PLEASE SAVE THESE INSTRUCTIONS

Installation and Wiring Instructions

220-240V/1/50Hz

VA150 A

STOCK Ref: 153110B

VA150 P

STOCK Ref: 152110B

VA 150 A, VA 150 P

WINDOW EXTRACT FAN

Installation and Wiring Instructions for the VA150 Kitchen A, P Extract Fan.

IMPORTANT:

READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

•This appliance is not suitable for installation in a shower cubical or enclosure and must be sited away from any

source of water spray, and must be out of reach of a person using a fixed bath or shower.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

•Sudden ductwork bends or transformations close to the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E. Regulations, or the appropriate standards of your country

and MUST be installed by a suitably qualified person.

B. The Fan should be provided with a local all pole isolator switch having a contact separation of at least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and Phase) complies with the rating label.

D. The Fan should only be used in conjunction with the appropriate Vent-Axia products.

E. It is recommended that the connection to the fan connecter terminals is made with flexible cable.

F. When the Fan is used to remove air from a room containing a fuel-burning appliance, ensure that the air

replacement is adequate for both the fan and the fuel-burning appliance.

G. This appliance is not intended for use by young children or infirm persons without supervision.

H. Young children should be supervised to ensure that they do not play with the appliance.

A. INSTALLATION.

WHERE TO FIT

AA short circuit of the airflow should always be avoided by siting the fan as far away as possible from and

opposite to the main source of air replacement.

FAN DIMENSIONS

Bi Before commencing work, the tables in Fig Bi should be read to ensure the fan will fit in the position

proposed.

THICKNESS OF GLASS

C1 Fans can be fitted in most types of glass with a fixing thickness up to 32mm, with the screws provided.

When fixing thickness exceeds 32mm, the unit should be secured with Extended Fixing Rods, available as an

accessory item (56 81 04). If the unit is to be installed in a location exposed to severe wind turbulence thicker

glass will be required – consult with Vent-Axia Technical Support for advice.

136

Suggested Minimum

Glass Thickness

PREPARATION FOR INSTALLATION (Dismantling)

D1 Place the fan unit, external grille downwards, on a flat surface.

D2 Unscrew grille securing screw located at the top of the grille. Remove internal grille.

D3 Slacken the two safety catch screws on the face of the housing. Depress the side catches.

D4 Lift off the housing.

D5 Remove the top cover from its housing. Check rating label to ensure that the fan unit is the correct voltage.

D6 Ease back the motor support safety catch located in the left-hand top corner of the base housing. Rotate

motor support assembly anticlockwise until the bayonet catches disengage from the base housing.

D7 Withdraw motor support assembly and place with the impeller downwards.

D8 Separate the base housing from the external grille assembly.

FITTING

For Dimensions see Bi

Measure the glass thickness and determine the length of fixing screw required (C1).

Glass thickness 4 to 17mm – Break/ cut off ends of screws supplied.

Glass thickness 16 to 32mm – Use screw as supplied.

Glass thickness 32mm and greater – Use extended rods (56 81 04) available as an accessory.

E1 From the inside, place the spigot centrally through the fixing hole with the connector hole upwards.

Ensure the rubber seal is correctly located over lugs and around the spigot.

E2 From the outside, place the exterior grille assembly over the projecting spigot, ensure that the grille

louvers are slanting downwards.

E3 From the inside, insert the four thumbscrews through the holes around the spigot. Finger-tighten the

screws progressively, in turn, to give an even pressure round the hole into the glass.

E4 Locate and replace the motor support assembly and turn clockwise until the safety catch is fully engaged.

WARNING: THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

REFER TO SECTION B– WIRING. BEFORE CONTINUING WITH RE-ASSEMBLING THE FAN

RE-ASSEMBLE (WINDOW/ WALL)

E5 Replace the housing with the top cover slot uppermost. Feed the pullcord (VA150P) through the slot in the

bottom of the housing. Ensure the arm protruding from the actuator housing is in its lower position, i.e.

shutter closed.

E6 With the two side catches fully engaged, tighten the catch safety screws.

E7 Replace the internal grille. Locate the bottom edge first and then engage the top. Tighten the securing

screw at the top of the grille.

E8 Switch on the mains supply. Check the fans operation.

VA150 P – 1) Pull the pullcord once and release. The shutter will open and the fan will commence extraction.

2) Pull the pullcord again and release. The shutter will close and the fan will stop.

VA150 A – 1) Switch on power supply (switch). The shutter will open and the fan will commence extraction.

2) Switch off power supply (switch). The shutter will close and the fan will stop.

PULLCORD ON

'P' MODEL ONLY

1 Phase Supply

(220-240V 50Hz).

Switched

Fused Spur

FUSE

Fan

B. WIRING.

WARNING: THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

Take the top cover. Make a suitable hole in the grommet. Pass the cable through the hole and slide the

top cover into the base housing.

VA150A and VA150P fans are Class II double insulated and MUST NOT BE EARTHED

A Cable Clamp is provided adjacent to the terminal block and must be used.

1) Loosen the cable clamp screws and pass the cable through the clamp.

2) Connect the LIVE (Brown) to the terminal L, and NEUTRAL (Blue) to the terminal N.

3) Tighten the cable clamp screws evenly, ensuring a secure grip on the outer sheath of the cable.

The Fan should be provided with a local all pole isolator switch. With contact separation of at least 3mm.

C. SERVICING AND MAINTENANCE.

WARNING: THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build

up of dirt or other deposits.

2. Remove the Indoor Grille (See Section D2 for instructions) and wash in warm soapy water.

3. Wipe the shutter blades with a damp cloth until clean.

4. Replace the Grille.

PRODUCT FICHE

For Residential Ventilation Units (Complying Commission Delegated Regulation (EU) No 1254/2014)

Name: Vent‐AxiaVent‐Axia

ModelID(StockRef.):VA150P‐152110VA150A‐153110

SECClassFF

SECValue('Average')13.9713.97

SECValue('Warm')6.326.32

SECValue('Cold')27.3227.32

LabelRequired?(Yes/No=Outofscope)NoNo

Declaredas:RVUorNRVU/UVUorBVURVU‐UVURVU‐UVU

SpeedDriveMulti‐SpeedMulti‐Speed

TypeHRS(Recuperative,Regenerative,None)NoneNone

ThermalEff:[(%),NA(ifnone)]N/AN/A

Max.FlowRate(m3/h)216.00216.00

Max.PowerInput(W):(@Max.FlowRate)19.0019.00

LWA:SoundPowerLevel(dB)54.5254.52

Ref.FlowRate(m3/s)0.040.04

Ref.PressureDiff.(Pa)N/AN/A

SPI[W/(m3/h)]0.130.13

ControlFactor&ControlTypology:(CTRL/Typology)

ControlFactor;CTRL1.001.00

ControlTypologyManualControlManualControl

Declared:‐MaxInternal&ExternalLeakageRates(%)forBVUsorcarry

over(forregenerativeheatexchangersonly), 

‐&Ext.LeakageRates(%)forDuctedUVUs;

N/AN/A

MixingRateofNon‐DuctedBVUsnotintendedtobeequippedwith

oneductconnectiononeithersupplyorextractairside;N/AN/A

PositionanddescriptionofvisualfilterwarningforRVUsintendedfor

usewithfilters,includingtextpointingouttheimportanceofregular

filterchangesforperformanceandenergyefficiencyoftheunit

N/AN/A

ForUVUs(InstructionsInstallRegulatedSupply/ExtractGrillesFaçade)InF&WInF&W

InternetAddress(forDisassemblyInstructions)www.vent‐axia.comwww.vent‐axia.com

Sensitivityp.Variation@+20/‐20Pa:(forNon‐DuctedVus)N/AN/A

AirTightness‐ID/OD‐(m3/h)(forNon‐DuctedVus)N/AN/A

AnnualElectricityConsumption:AEC(kWh/a)1.731.73

AnnualHeatingSaved:AHS(kWh/a)

AHS:Average13.9713.97

AHS:Warm6.326.32

AHS:Cold27.3227.32

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Vent-Axia

Vent-Axia

Vent-Axia VASF100B Instrucciones de montaje

Vent-Axia

Vent-Axia ResponseSELV TP Instrucciones de montaje

Vent-Axia

Vent-Axia SVARA Manual de usuario

Vent-Axia

Vent-Axia Silhouette 100T Instrucciones de montaje

Vent-Axia

Vent-Axia 441511A Instrucciones de montaje

Vent-Axia

Vent-Axia eMF Series Instrucciones de montaje

Vent-Axia

Vent-Axia SOLO Plus Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Svelte Series Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon dMEV Unit T Instrucciones de montaje

Vent-Axia

Vent-Axia GALAXY GDB Series Instrucciones de montaje

Vent-Axia

Vent-Axia Centrif Duo Instrucciones de montaje

Vent-Axia

Vent-Axia SUPRA 100 T Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Quadra Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Centra Series Instrucciones de montaje

Vent-Axia

Vent-Axia Advance S Manual de usuario

Vent-Axia

Vent-Axia 427477A Instrucciones de montaje

Vent-Axia

Vent-Axia ATQ 400-14C Instrucciones de montaje

Vent-Axia

Vent-Axia SOLO Plus SELV Instrucciones de montaje

Vent-Axia

Vent-Axia SOLO Plus Instrucciones de montaje

Vent-Axia

Vent-Axia ATQ10012D Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Sylph 100CV Instrucciones de montaje

Vent-Axia

Vent-Axia MULTIVENT MVDCH Manual de instrucciones

Vent-Axia

Vent-Axia VA100SVL12 Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Sylph Series Instrucciones de montaje

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje