Vemer ADR-D 400 D90 Manual de usuario
ANALIZZATORE
DI RETE TRIFASE 90A
ADR-D 400 D90
Manuale d’Uso
User Manual
THREE-PHASE NETWORK ANALYSER 90A
PDF
- 15 -
User Manual - ADR-D 400 D90
English
Index
Safety instructions pag. 16
Technical specications pag. 17
Description pag. 19
Dimensions pag. 19
Installation pag. 20
Selecting programming parameters pag. 21
Reading of quantities pag. 24
Serial output RS 485 pag. 26
Error messages pag. 27
Reference standards pag. 28
- 16 -
User Manual - ADR-D 400 D90
English
User Manual
THREE-PHASE NETWORK ANALYSER 90A
Read all the instructions carefully
The ADR-D 400 D90 network analyzer is a direct connection digital multimeter for
three-phase systems up to 90 A for true effective value measurements (TRMS). The
isolated RS-485 serial output allows, through the MODBUS protocol functions and
the use of the relative registers, to connect the analyzer to a Master device (PC/
PLC...) for data visualization and archiving.
SAFETY INSTRUCTIONS
During the installation and operation of the device, observe the following
instructions:
1) The device must be installed by a qualied person
2) The device must be installed in an electrical panel which, after installation,
leaves terminals inaccessible
3) The electrical system in the building where the device is installed must
feature a switch or circuit breaker: this must be near the device and in a
position that can be easily reached by operators
4) A protection device against over-currents must be installed in the electrical
system, upstream of the instrument
5) Connect the device as shown in the diagrams of this manual
6) Before making contact with terminals, ensure that conductors to be
connected to the device are not live
7) Do not power or connect the device if any part of it is damaged.
NOTE: Network analyzer ADR-D 400 D90 is aimed for use in places with over-
voltage category III and pollution degree, 2 as per EN 61010-1
Code Model Description
VE045100
ADR-D 400 D90 Direct-connection three-phase network analyzer 90A
- 17 -
User Manual - ADR-D 400 D90
English
TECHNICAL SPECIFICATIONS
• Power supply: 400 Vac (-15%/+10%), 50/60 Hz (terminals 2 and 3)
• Electrical quantities measured:
−
Phase voltage, voltage between lines (chain), and system voltage
−
Phase and system current
−
Active, reactive, and apparent phase and system power
−
Active and reactive phase and total system Energy (zeroable)
−
Phase and system power factor (cos
)
−
Frequency
• Connection type:
−
3-wire connection with neutral
−
3-wire connection without neutral: only for symmetrical and balanced systems
• Voltmetric inputs: Vmax = 440 V rms (phase – phase)
Vmax = 3x253 V rms (phase – neutral)
• Amperometric inputs: Ib= 10 A; Imax = 90 A
• Maximum overload in continuos use mantaining class 1: 100 A
• Insulated serial output RS-485, for communication protocol MODBUS RTU
• Termination:
−
voltmetric inputs: 4-pole terminal strip; maximum section of wires: 2,5 mm2
−
RS485 serial line: 2-pole terminal strip; maximum section of wires: 2,5 mm2
−
amperometric inputs: direct connection, with the current wires inserted into the
suitable holes; maximum section of current leads: 25 mm2; maximum diameter of
through hole: 12,5 mm
• Maximum consumption (device only):
−
voltage circuits < 2.5 VA
−
current circuits < 2.5 VA
−
power supply < 4 VA
• Display: LCD display
• Dimensions: 7 DIN sizes
• Operating temperature: -10 °C ÷ 45 °C
• Storage temperature: -10 °C ÷ 60 °C
• Relative humidity: 10% ÷ 90% non condensing
• Protection rating: IP20/IP51 on the front
- 18 -
User Manual - ADR-D 400 D90
English
RESOLUTION AND ACCURACY
• Voltage
−
Maximum reading: 266 V (phase - neutral)
−
Accuracy: ±0,5% full scale ± 1 digit (full scale: 253 V)
−
Resolution: 1 V
• Current
−
Minimum reading: 0,10 A
−
Maximum reading: 95,0 A
−
Accuracy: ±0,5% full scale ± 1 digit (full scale: 90 A)
−
Resolution: 0,01 A (range 0,10÷9,99 A) or 0,1 A (range 10,0÷90,0 A)
• Active power
−
Accuracy: ± 1% full scale ± 1 digit at 50 Hz
(full scale: 100 W, 1 kW, 10 kW, 100 kW)
−
Resolution: 0,1 W (range 0÷99,9 W) - 1 W (range 100 W÷999 W)
0,01 kW (range 0,01 kW÷9,99 kW)
0,1 kW (range 10 kW÷100 kW)
• Reactive power
−
Accuracy: ±1% full scale ± 1 digit
(full scale: 100 Var, 1 kVar, 10 kVar, 100 kVar)
−
Resolution: 0,1 Var (range 0÷99,9 Var)
1Var (range 100 Var÷999 Var)
0,01 kVar (range 0,01 kVar÷9,99 kVar)
0,1 kVar (range 10 kVar÷100 kVar)
• Active energy
−
Accuracy: class 1 to standard EN 62053-21 (Ib=10 A; Imax=90 A)
−
Resolution: 0,1 kWh
• Reactive energy
−
Accuracy: class 3 to standard EN 62053-23 (Ib=10 A; Imax=90 A)
−
Resolution: 0,1 kVarh
• Power factor (cos
)
−
Accuracy: ±1% ± 1 digit
−
Resolution: 0,01
• Frequency
−
Accuracy: ±0,1 Hz ± 1 digit (from 47 Hz a 63 Hz)
−
Resolution: 0,1 Hz
- 19 -
User Manual - ADR-D 400 D90
English
DESCRIPTION
FRONT VIEW
TERMINALS AND KEYS
Terminal 1: Neutral (required for non-symmetrical non-balanced systems)
Terminals 2, 3, 4: voltage inputs (L1, L2, L3)
Terminals 5 (-) and 6 (+): Serial communication line RS-485
Through holes for direct current connection to L1, L2, L3
Key to be used to conrm and view system quantities
Previous page Key
Next page key
Programming key
OK
PRG
ADR-D 400 D90
10(90)A
3x230/400 V ~ 50/60Hz
DIMENSIONS (mm)
FRONT VIEW SIDE VIEW
87
125.7
65
- 20 -
User Manual - ADR-D 400 D90
English
INSTALLATION
WIRING DIAGRAM
L1
N
L2
L3
LOAD
NOTE:
Connection of the neutral conductor may ONLY be omitted for balanced
symmetrical three-phase systems
INSTALLATION
Network analyzer ADR D 400 D90 may only be used in three-phase systems 230 Vac
Phase-neutral, with 400 Vac Phase-Phase voltage between lines.
For installation, follow the connection diagram shown above:
− for 4-wire three-phase systems (3 phases + neutral) also with non-symmetrical and/
or non-balanced systems, connect the neutral lead to terminal 1
− for 3-wire three-phase symmetrical and balanced systems, it is possible not to
connect the neutral lead
For correct measurement, the 3 phase leads coming from the distribution panel must
be inserted in the through holes vertically from above; failure to do so will cause a
connection-error warning to appear on the display. In case of a connection error, the
display will indicate which phase or phases are misconnected (cfr. “ERROR MESSAGES
– MISCONNECTION” ).
- 21 -
User Manual - ADR-D 400 D90
English
SELECTING PROGRAMMING PARAMETERS
The following functions are accessed by holding down the PRG key for at least 2
seconds:
− viewing built-in software version and date
− backlighting control
− zeroing total active and reactive energy values
− conguring serial output RS-485
To scroll the various parameters and conrm the values entered, press the OK key. To
change the values or alter the option, press
or .
As soon as the last page is conrmed the programming mode is exited; this also occurs
if no key is pressed for at least 25 seconds: in this case, the parameter that was not
conrmed using the OK key, is not stored.
1) DATE AND VERSION OF BUILT-IN SOFTWARE
• These values cannot be altered
• To move on to the next page (backlighting control), press OK
2) BACKLIGHTING CONTROL
• Press the key
o to respectively select “NO” (backlighting off) or “TIME”
(backlighting ON for 60s after any key is pressed)
• Press the OK key to conrm the selection and move on to the next page (Zeroing
Active Energy meter)
- 22 -
User Manual - ADR-D 400 D90
English
3) ZEROING THE ACTIVE-ENERGY METER
• Press the key
to select “NO” or for “YES”
• Press the OK key to conrm the selection and move on to the next page (Zeroing the
Reactive Energy meter)
4) ZEROING THE REACTIVE-ENERGY METER
• Press
to select “NO” or to select “YES”
• Press the OK key to conrm the selection and move on to the next page (RS-485
address)
5) RS-485 ADDRESS
• The address range is between 1 and 247
• Press the PRG key to select the digit to be altered (units, tens, hundreds)
• Press the key
o to select the value
• Press the OK key to conrm the address and move on to the next page (RS-485
communication speed)
Tabla de contenidos
Otros manuales de Instrumento de medición de Vemer
Vemer
Vemer EVM-2DIN Manual de usuario
Vemer
Vemer Energy-230 LC Manual de usuario
Vemer
Vemer Energy-230 D22 PULSE Manual de usuario
Vemer
Vemer TUO Wi-Fi Lite Manual de usuario
Vemer
Vemer EVS-2DIN Manual de usuario
Vemer
Vemer ENERGY-230 Manual de usuario
Vemer
Vemer ADR Series Manual de usuario
Vemer
Vemer ENERGY-400 D90 Manual de usuario
Vemer
Vemer PC3R Manual de usuario
Vemer
Vemer ADR Series Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario