Velleman K8059 Manual de usuario
2 CHANNEL RF CODELOCK TRANSMITTER
K8059
ILLUSTRATED ASSEMBLY MANUAL H8059IP-1
Total solder points: 63
Difficulty level: beginner 12345 advanced
ForusewithK8057/VM109
2ChannelRFreceiver
3
Features:
For use with the K8057/VM109 2-channel RF receivers.
Generates unique 32-bit code.
More than 1,000,000,000 unique codes.
Code can easily be changed for safety purposes.
Choose continuous or 'burst' transmission.
LED indicator.
Limited compatibility with K6706 - K6706A - K6706B/G
Specifications:
Power supply: 12V battery V23GA, GP23GA,... (not incl.)
433MHz operation
Open field range of up to 30m possible
Dimensions: 63 x 40 x 16mm (2.5" x 1.6" x 0.6")
Features & Specifications
Velleman hereby certifies that the device K8059 meets the essential requirements and all other relevant
stipulations of directive 1999/5/EG and 1995/5/EC.
For the complete conformity declaration check out :
Http://www.velleman.be/downloads/doC/CE_K8059.pdf
4
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it oftenon a wet sponge or cloth, to keep it clean; then apply solderto the tip, togive it a wetlook. This is called ‘thinning’ and will
protect the tip,and enables you to makegood connections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒Make sure the skill level matches your experience, to avoid disappointments.
⇒Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒Perform the assembly in the correct order as stated in this manual
⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒Values on the circuit diagram are subject to changes.
⇒Values in this assembly guide are correct*
⇒Use the check-boxes to mark your progress.
⇒Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates,indicated as ‘NOTE’ on a separateleaflet.
0.000
5
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE
CORRECT MOUNTING SEQUENCE !
You will find the colour code for the resistances and the LEDs on our website:
http://www.velleman.be/common/service.aspx
6
Construction
SW1 : KRS0611
SW2 : KRS0611
SW3 : KRS0611
5. Push buttons
X1 : SAW433
4. SAW resonator
X...
D1 : BAT85
D2 : BAT85
1. Diodes. Watch the polarity!
D...
CATHODE
ZD1 : 5V1 / 500mW
2. Zenerdiode. Watch the
polarity!
ZD...
CATHODE
R1 : 33K (3 - 3 - 3 - B)
R2 : 33K (3 - 3 - 3 - B)
R3 : 33K (3 - 3 - 3 - B)
R4 : 47 (4 - 7 - 0 - B)
R5 : 220 (2 - 2 - 1 - B)
R6 : 2K7 (2 - 7 - 2 - B)
3. 1/8W Resistors
R...
IC1 : 8p
6. IC socket. Pay attention
to the position of the notch!
PIN1
7
Construction
T1 : MPSH10
10. Transistor
+
-
Check for good attachment of
the solder to the contacts
7. Battery contacts
C1 : 1pF (1)
C2 : 4p7 (4.7)
C3 : 100pF (101)
Bend C3 away from the LED
C4 : 100pF (101)
C5 : 100pF (101)
C6 : 100nF (104)
9. Capacitors
IC1 : VK8059
VK8059=(ProgrammedPIC12F629)
Pay attention to the position
of the notch!
11. IC. Pay attention to the
notch !
Affix the supplied sticker to the
back of the housing.
12. Sticker
Velleman
SRFCE
433,92 MHz
LD1 : 3mm blue
8. LED
COLOR= 2...5
LD.
CATHODE
8mm
LD...
-
+
8
The transmitter comes with a factory set default code. However, for security reasons, it might be wise not to
use the default code.
1. To program your unique code :
Hold SW1(*) (left button).
Briefly press the 'program'-button (SW3) 3 times. The LED will flash 3 times.
Release SW1.
Your unique 32-bit code has been generated and stored.
(*If you hold SW2 (right button) instead of SW1 (left button), the unit will generate and store your unique 32-
bit code and the transmitter will be configured in such a way that continuous transmission is not possible i.e.
if you hold either button transmission will stop after a +/- 1s)
2. To return to the default code :
Hold SW1 (left button).
Hold the 'program'-button (SW3).
After +/- 10s the led will flash 5 times.
Release both buttons.
Your code has been erased.
To set a new code, see point 1.
Use
13. Use
9
3.Compatibility with previous transmitters (K6706 - K6706A - K6706B - K6706G) :
3 different codes can be generated, solder a bridge as indicated below.
MODIFY EXCISTING TRANSMITTERS AND RECEIVERS :
-
+
-
+-
+
UM3758
No code UM3758
Pin1with -UM3758
Pin1with +
NEW
OLD
10
14. Schematic diagram.
Schematic diagram
C3
100p
C1
1p
C2
4p7
T1
MPSH10
R5
220-1/8W
R4
47-1/8W
LD1
LED3RL
X1
SAW433
R1
33K-1/8W
C4
100p
SW1
SW KRS0611
SW2
SW KRS0611
GP4/T1G/OSC2/CLKOUT
3
Vdd
1
GP5/T1CKI/OSC1/CLKIN
2
GP3/MCLR/Vpp
4
GP2/T0CKl/INT/COUT
5
GP0/CIN+/ICSPDAT
7
GP1/CIN-/ICSPCLK
6
Vss
8
IC1
PIC12F629
J2J1
SW3
SW KRS0611
R3
33K-1/8W
R6
2K7-1/8W
D2
BAT85
D1
BAT85
C5
100p
C6
100n
ZD1
5V1/0.5W
BAT1
12V
R2
33K-1/8W
L
Tabla de contenidos
Otros manuales de Transmisor de Velleman
Velleman
Velleman vm118 Manual de usuario
Velleman
Velleman PMR3 Manual de usuario
Velleman
Velleman K6710 Manual de usuario
Velleman
Velleman K8049 Manual de usuario
Velleman
Velleman K8074 Manual de usuario
Velleman
Velleman VM121 Manual de usuario
Velleman
Velleman K8058 Manual de usuario
Velleman
Velleman K8074 Manual de usuario
Velleman
Velleman AVMOD11 Series Manual de usuario
Velleman
Velleman CARSFM3 Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
