Velleman High-Q Velleman-kit K8086 Manual de usuario
TELEPHONE RING DETECTOR WITH RELAY OUTPUT
K8086
ILLUSTRATED ASSEMBLY MANUAL H8086IP-1
Total solder points: 61
Difficulty level: beginner 1 2 3 4 5 advanced
Simplyconnect inparallelwith phoneline.
Acceptsstandardadaptor&telephone plug.
2
Features:
simply connect in parallel with phone line
powerful led flashes when phone rings
the unit will feature a relay output if connected to a 12VDC power supply
relay output: continuous or on/off to the rhythm of ringing of the telephone
complete with enclosure
great for noisy environments, for the hearing impaired, as addional ringer, to replace existing ringer, ...
accepts standard adaptor & telephone plug
Specifications:
10.000 mcd led !
connects to PSTN line
RJ11 connector
supply: 12VDC/100mA adapter (Ex. PS1203)
output Contact (NO): 1A max.
dimensions: 80x55x35mm / 3,15 x 2,16 x 1,37"
Features & Specifications
Includes:
attractive enclosure
adhesive strips for easy fixing
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.
Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip,
and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thin raisin-core solder. Do not use any flux or grease.
A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes.
Needle nose pliers, for bending leads, or to hold components in place.
Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.
Follow the instructions carefully. Read and understand the entire step before you perform each operation.
Perform the assembly in the correct order as stated in this manual
Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*
Use the check-boxes to mark your progress.
Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
0.000
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE.
ALWAYS CHECK THEIR VALUE ON THE PARTS LIST!
REMOVE THEM FROM THE TAPE ONE AT A TIME !
5
R1 : 1M (1 - 0 - 5 - B)
R2 : 2K2 (2 - 2 - 2 - B)
R3 : 15K (1 - 5 - 3 - B)
R4 : 100K (1 - 0 - 4 - B)
R5 : 1K (1 - 0 - 2 - B)
3. Resistors
R...
Construction
D1 : 1N4148
D2 : 1N4007 D...
CATHODE
IC1 : 6P
4. IC socket, Watch the
position of the notch!
1. Diodes. Watch the polarity!
ZD1 :20V0
ZD2 :20V0 ZD...
CATHODE
2. Zener diodes. Watch the
polarity!
D3 : 1N4007
D4 : 1N4007
D5 : 1N4007
D6 : 1N4007
5. Vertical diodes. Watch the
polarity!
SK4 : 2p
open = blink relay
closed = continuous relay
6. Pinheader + shunt
T1 : BC557B
7. Transistor
T...
C2 : 100µF / 25V
C3 : 47µF / 25V
8. Electrolytic Capacitors.
Watch the polarity !
C...
SK3 : 2p
9. Terminal blocks
6
Construction
IC1 :4N27
15. IC, watch the position of
the notch!
SK2 : 12VDC
10. DC-jack
-
SK... +
SW
LD1 : 5mm (super red)
11. LED. Watch the polarity!
SK1 : 4p (type RJ11)
12. Modular Jack
C1 : 1µF / 275VAC
13. Capacitor
RY1 :VR15M121C
14. Relay
RY...
7
Connection samples
16. Connection examples
1. LED flash 2. LED flash + relay ouput
continuous
relay output
blinking
relay output
output mode selection
Telephone line
12VDC
+
-
24V / 1A
Phone
Company
Phone
Company
Telephone line
8
17. Assembly
Assembly
ADHESIVE
STRIP
9
Schematic diagram.
Schematic diagram
10
PCB
PCB
Tabla de contenidos
Otros manuales de Sensor de seguridad de Velleman
Velleman
Velleman ham1011 Manual de usuario
Velleman
Velleman PIR600 Manual de usuario
Velleman
Velleman PIR1300 Manual de usuario
Velleman
Velleman PIR416 Manual de usuario
Velleman
Velleman PEREL EMS101 Manual de usuario
Velleman
Velleman PIR416 Manual de usuario
Velleman
Velleman ham1011 Manual de usuario
Velleman
Velleman PIR416 Manual de usuario
Velleman
Velleman PIR1200B Manual de usuario
Velleman
Velleman PIR105 Manual de usuario
Velleman
Velleman PIR45 Manual de usuario
Velleman
Velleman PIR500 Manual de usuario
Velleman
Velleman PIR451 Manual de usuario
Velleman
Velleman PIR415 Manual de usuario
Velleman
Velleman VTEMF Manual de usuario
Velleman
Velleman ZLLPIR Manual de usuario
Velleman
Velleman HAA52N Manual de usuario
Velleman
Velleman DVMEMF Manual de usuario
Velleman
Velleman PIR1200W Manual de usuario
Velleman
Velleman PEREL EMS108 Manual de usuario
