ServerCall Paging System
V
eDoSign
Nolenslaan 8, 3741 VT Baarn, Tel. +31 (0)35 543 07 38, Fax +31 (0)35 543 57 56, [email protected]Innovatieve communicatie oplossingen en advies voor hospitality gerelateerde toepassingen - www.vedosign.com
Manual
2. Range Test
Factory Default : OFF
With this feature you can determine
what distance your transmitter will cover.
You only need to test range if you have a
very large restaurant or are having
problems with your system. This system
should cover most locations.
• Remove a couple of pagers from the
charging rack.
• At the Set Range Test menu, press
“ENTER” key to go to “Range Test”
configuration menu.
• Press “2X” or “3X” key to turn range
test “ON”.
• Press “ENTER” to start the range test.
As soon as range test is activated you’ll
notice the pagers flash or vibrates once
every 10 seconds. Walk around your
property. When you reach the point
where the pagers do not flash consis-
tently, this is your maximum range.
• Press the “CANCEL” key to stop the range
test. Press the “CANCEL” key again to
exit the system programming menu.
NOTE: The transmitter has an auto shut
off feature that will stop the range test
after 15 min.
3. Set Pager Alert
Factory Default: Vibe Only
For use with rechargeable pagers only! With
this feature you have the option of chan-
ging the way your pagers alert the server/
employee. Be sure that all pagers are re-
turned before performing this procedure.
To change the alert mode of your pagers
follow these instructions:
• Remove all the pagers from the charging
unit or simply unplug the power supply
that is connected to the charging bases
(pagers will go through their demo
page).
• At the “Set Pager Alert” menu, press
the “ENTER” key to go to “Set Pager
Alert” configuration menu.
• Press the “2X” or “3X” key to scroll
through the different alert options.
• After making a selection, press the
“ENTER” key 4 times. After sending
the code, the pagers will now respond
with your new selection.
• Press the “CANCEL” key to exit the
system programming menu
• Return all the pagers to the charging
base or plug the power supply back in.
The pagers are ready to receive the page
with the new alert.
4. Setting the “Out of Range”
Factory Default: OFF
For rechargeable pagers only.
TURNING THE OUT OF RANGE ON (or OFF)
• Remove all the pagers from the
charging unit or unplug the power
supply that is connected to the first
charging rack.
• Press the “ENTER” key to go to “Out of
Range” configuration menu.
• At the “Out of Range” menu, press the
“2X” or “3X” key to turn the out of
range ON (or OFF).
• Press the “ENTER” key 4 times. After
sending the signal, all the pagers will
light up once to tell you that they re-
ceived the new code.
• Press “CANCEL” key to exit the system
programming menu.
• Return all the pagers to the charging
base or plug the power supply back in.
The pagers are ready to receive the page
with the out of range ON (or OFF).
5. Transition Page
Factory Default: 30 sec
The transition page is the time between
“re-pages” should your staff be tardy in
picking up their food.
You may set your system to page in the
following ways:
1. Page once and then reset. (Transition OFF)
2. Page three times and then reset
3. Page three times and page the manager
with the server number (this option
requires someone to clear the page by
pressing the button again).
TO TURN TRANSITION PAGING ON (OR OFF)
• Press the “ENTER” key to go to
“Transition Page” configuration menu.
• At the “Transition Page” menu, press
the “2X” or “3X” key to turn the transi-
tion page ON (or OFF).
(NOTE: If this option is OFF, the pager
will be paged only once).
• Select the transition time then press
“ENTER” key.
• Press “CANCEL” key to exit the system-
programming menu.
TO SET TRANSITION TIME:
From the set up menu:
• Press the “2X” Key until you see
“Transition Page”. The display should
show “ON”
• Press “Enter”. You should see
“Transition Timer >15 secs”
• Press “2X” or”3X” to scroll through the
different times. (15, 30, 45, 60, 120)
• When the desired transition time is
displayed in the window press
“Enter”
• Scroll for more options or
“Cancel” to exit.
For question or assistance
please contact us.
Tel: +31 (0)35 543 07 38
