Vantec UGT-ST320R Manual de usuario
4-Port SATA 150 PCI Combo Host
Card w/RAID
User Manual
Model: UGT-ST320R
All brand names and trademarks are properties of their respective owners.
www.vantecusa.com
UGT‐ST320R Page2
Features
zSilicon Image SiI3512 SATA controller chip
zCompliant with PCI Specification, Rev. 2.3
zCompliant with Serial ATA 1.0 specification
zProvides two independent channels to support up to two Serial
ATA drives
zSupports RAID0(striping) and RAID1(mirroring) for speed and
data protection respectively
zHDDs function normally when not in RAID sets
zSupports SATA up to 150MB/Sec
zSupports Windows® 2000/XP/2003/Vista/7 (32/64 bit)
Connectors
z2 x internal SATA connectors
z2 x external eSATA connectors
System Requirements
zPentium-class computer with one available PCI slot
zWindows® 2000/XP/2003/Vista/7 (32/64 bit)
UGT‐ST320R Page3
Package Contents
zVantec 4-Port SATA 150 PCI Combo Host Card w/RAID x 1
zSATA Cables x 2
zInstallation Guide x 1
zDriver CD x 1
*User’s Manual Is on Driver CD
Hardware Description
Note: There are four SATA ports in SATA 150 PCI RAID Card
2-Channel. We name these ports from A to D. Ports A & B are internal
SATA ports. Ports C & D are external SATA ports. Changing the
jumper setting allows you to select between external and internal ports
to use. By default, Port A and B are working.
E (Jumper Settings)
JP Description Active Port
1-2 close Enable SATAPort CJ1-J4
2-3 close Enable SATA Port A
1-2 close Enable SATAPort DJ5-J8
2-3 close Enable SATA Port B
UGT‐ST320R Page4
UGT‐ST320R Page5
Hardware Installation
1. Turn off the power to your computer and any other connected
peripheral devices.
2. Unplug the power cord form the back of the computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card’s bus connector with
the selected PCI slot on the motherboard. Push the board down
firmly, but gently, until it is well seated.
6. Replace the slot bracket’s holding screw to secure the card.
Device Connection
The Vantec 4-Port SATA 150 PCI Combo Host Card w/RAID is a
two channel Serial ATA controller that supports up to two Serial ATA
hard disk drives. It is recommended to use identical hard drives for all
RAID configurations.
1. Install your hard disk drive(s) in chassis.
2. Connect the Serial ATA hard disk drive to the system power
supply using the included Serial ATA power cable.
3. Connect one end of the Serial ATA cable to the hard disk drive.
UGT‐ST320R Page6
4. Attach the other end of the Serial ATA cable to the Serial ATA port
on the SATA 150 PCI Raid Card 2-Channel
5. Follow the same instructions to connect up to two hard drives.
Device connection is now complete.
6. Replace the computer cover and reconnect the power cord.
RAID Arrays
RAID Arrays are setup in the Vantec 4-Port SATA 150 PCI Combo
Host Card w/RAID’s BIOS.
RAID 0 (Striping)
This RAID array to be used on New/Blank hard drives. Striping will
destroy existing data on the hard drive. Auto Configuration is
recommended. For applications that require custom chunk size,
Manual Configuration is offered.
Auto configuration (recommended)
The default chunk size is 64k when selecting Auto configuration.
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
UGT‐ST320R Page7
2. At the next screen select Create RAID Set, then press Enter.
3. Select Striped, then press Enter.
4. Select Auto configuration, then press Enter.
5. When asked Are You Sure (Y/N)?, press Y to accept.
6. Press Ctrl+E to exit the BIOS.
7. When asked Are you sure to exit (Y/N)?, press Y to exit and
reboot.
8. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
Manual configuration
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
3. Select Striped, then press Enter.
4. Select Manual configuration then press Enter
5. Select the first drive, press Enter.
6. Select the second drive, press Enter.
7. Select chunk size from 4k, 8k, 16k, 32k, 64k or 128k, then press
Enter.
UGT‐ST320R Page8
8. When asked Are You Sure(Y/N)?, press Y to accept.
9. Press Ctrl+E to exit the BIOS.
10. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot.
11. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
RAID 1 (Mirror)
For New/Blank Hard Drives
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
3. At the next screen select Mirrored then press Enter.
4. Select Auto configuration, then press Enter.
5. When asked Are You Sure(Y/N)?, press Y to accept.
6. Press Ctrl+E to exit the BIOS.
7. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot.
8. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
UGT‐ST320R Page9
For Existing Hard Drives with Data
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
3. At the next screen select Mirrored then press Enter.
4. Select Manual configuration, then press Enter.
5. Select the Source drive, press Enter.
6. Select the Target drive, press Enter.
7. Enable Disk Copy, select Yes, then press Enter.
Note: Enable Disk Copy – Copy current content of source driver to
mirror drive; Disable Disk Copy – RAID 1 set formed must be
repartitioned and reformatted to guarantee the consistency in their
contents.
8. Press Ctrl+E to exit the BIOS.
9. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot.
Note: If during boot the RAID BIOS reports an RAID1 set is in
Rebuild status, The rebuild will continue after boot sequence is
complete, disregard the message, continue booting, and let the Mirror
rebuild.
UGT‐ST320R Page10
Rebuilding a Failed Mirror Set
When a failure to one member occurs, you will be notified either by the
RAID BIOS during boot or by the SATARAID GUI while in
Windows. The steps below will guide you in rebuilding a failed mirror
set.
1. Replace the failed drive with one of equal or greater capacity, then
start the computer.
2. During boot press Ctrl+S or F4 to enter the RAID BIOS.
3. Select Rebuild Mirrored Set then press Enter.
4. Select the desired set and then press Enter.
5. When asked Are You Sure(Y/N)?, press Y to confirm.
6. The set will be rebuilt.
Deleting RAID Arrays
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. Select Delete RAID Set, then press Enter.
3. Select the RAID set then press Enter.
4. When asked Are You Sure(Y/N)?, press Y to confirm.
Tabla de contenidos
Otros manuales de Tarjeta PCI de Vantec
Vantec
Vantec UGT-PC345 Manual de usuario
Vantec
Vantec UGT-PC371AC Manual de usuario
Vantec
Vantec UGT-PC20SR Manual de usuario
Vantec
Vantec UGT-PC2S1P Manual de usuario
Vantec
Vantec 2+1 FireWire 800/400 PCIe Combo Host Card Manual de usuario
Vantec
Vantec UGT-FW050 Manual de usuario
Vantec
Vantec UGT-ST644R Manual de usuario
Vantec
Vantec 3-Port FireWire 400 PCIe Host Card Manual de usuario
Vantec
Vantec eSATA PCI & PCI-E Card & CardBus Manual de usuario
Vantec
Vantec UGT-PC10PL Manual de usuario
Vantec
Vantec 2+1 Serial & Parallel PCI Host Card Manual de usuario
Vantec
Vantec UGT-PCE430-2C Manual de usuario
Vantec
Vantec UGT-PC312 Manual de usuario
Vantec
Vantec UGT-IS100R Manual de usuario
Vantec
Vantec UGT-PC210 Manual de usuario
Vantec
Vantec UGT-PC341 Manual de usuario
Vantec
Vantec UGT-ST622 Manual de usuario
Vantec
Vantec FireWire 400 Manual de usuario
Vantec
Vantec SATA 150 PCI RAID Card Manual de usuario
Vantec
Vantec UGT-ST310R Manual de usuario
Manuales populares de Tarjeta PCI de otras marcas
Belkin
Belkin F5D7000F Manual de usuario
Pericom
Pericom PI7C7100 Manual de usuario
ADLINK Technology
ADLINK Technology cPCI-3548 Manual de usuario
Digium
Digium TE200 Series Manual de usuario
Allo.com
Allo.com 2nd Gen E1/T1/J1 Manual de usuario
Western Digital
Western Digital FireWire PCI Adapter Manual de usuario