Vantage Hearth HD 7100C Manual de usuario
2
Safety Instructions
English
S
afety Instructions
This product has been manufactured to satisfy the international safety standards.
Please read all of safety and operating instructions before operating the product and keep this
manual for future reference.
MAINS SUPPLY
AC 90-250V~, 50/60Hz
Operate your product only from the type of power supply indicated on the marking label. If you
are not sure of the type of power supplied to your home, consult your local power company.
Disconnect the STB from the mains before you start any maintenance or installation procedures.
OVERLOADING
Do not overload a wall outlet, extension cord or adapter as this may result in electric re or
shock.
LIQUIDS
The product should not be exposed to any liquids such as dripping or splashing. No objects
lled with liquids, such as vases, should be placed on the apparatus,
CLEANING
Before cleaning, disconnect the product from the wall outlet, Use a cloth lightly dampened with
water (no solvents) to clean the exterior.
VENTILATION
The slots on top of the product must be left uncovered to allow proper airow to the unit. Do not
stand the product on soft furnishings or carpets. Do not expose the product to direct sunlight,
place it near a heater. Do not stack electronic equipment on top of the product.
ATTACHMENTS
Do not use any attachment that is recommended by the manufacturer it may cause a hazard or
damage the product.
CONNECTION TO THE SATELLITE DISH LNB
Disconnect the product from the mains before connecting or disconnecting the cable from the
satellite dish. Failure to do so can damage the LNB.
CONNECTION TO THE TV
Disconnect the product from the mains before connecting or disconnecting the cable from the
satellite dish. Failure to do so can damage the TV.
LOCATION
Place the product indoors in order not to expose to lightning, rain or sunlight.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplier) that product heat.
LIGHTNING, or NOT IN USE
Unplug the product from the wall outlet and disconnect the cable during a lightning storm or
when unused for a long time.
SERVICING
Do not attempt service that this product yourself, as opening or removing covers may expose
you to dangerous voltage or other hazard. Refer all servicing to qualied service personnel.
“The mains plug is used as the disconnect device. Then disconnect device shall remain
readily operable”
Contents
3
English
C
ontents
Safety instructions ................................ 2
Chapter 1
Before You Begin................................... 4
General Features................................. 4
Accessories.......................................... 4
Chapter 2
Controls and Functions ........................ 5
Front Panel .......................................... 5
Rear Panel........................................... 5
Remote Control Unit ............................ 6
Chapter 3
Connections........................................... 8
Location of your receiver........................ 8
Connecting your receiver with
dish system ............................................ 8
Connecting your analog receiver ........... 9
Connecting your receiver to TV.............. 9
Connecting your receiver to VCR
(depending on model) ............................ 9
Connecting external audio/Hi-Fi system ... 9
Connecting digital audio system ............ 9
Chapter 4
Initial Settings and Operations............. 10
Menu Information................................. 10
Getting Started..................................... 10
Selecting the On Screen Display (OSD)
Language ............................................... 10
Basic Operation ................................... 11
Switching Channel ................................. 11
Volume Control....................................... 11
Info Bar................................................... 12
Selecting the soundtrack........................ 12
Selecting the OSD teletext, VBI teletext,
Subtitle and DVB subtitle ....................... 12
MoSAic .................................................. 13
Sleep Timer Function ............................. 13
Zoom Function ....................................... 13
Channel List ........................................... 13
To view channel list in specic order
(Alphabet/Satellite/Provider/HD) ............ 14
Electronic Program Guide (EPG)........... 14
Chapter 5
Menu Map............................................... 15
Main Menu.............................................. 16
Installation............................................ 16
Auto Scanning........................................ 16
Manual Scanning ................................... 16
Defaults Setting...................................... 17
System Setup....................................... 17
Language Setting................................... 17
OSD Setting ........................................... 18
Media Settings ....................................... 18
Time Setting ........................................... 19
Reservation Setting................................ 19
System Information ................................ 19
Channel Setup ..................................... 20
Delete Channels..................................... 20
Delete All Channels................................ 20
Favorite Channels.................................. 21
Edit Channels......................................... 21
SW Manager .......................................... 22
Parental Lock....................................... 22
Channel Lock ......................................... 22
Lock Control........................................... 23
Change Pin Code................................... 23
Game ................................................... 23
Multimedia............................................ 24
Conditional Access............................... 25
Troubleshooting .................................... 26
Specications ........................................ 27
Chapter 1 >> Before You Begin
4English
B
efore You Begin
General Features
• Accurate, Brilliant Friendly OSD with Full Function
• MPEG-2 (MP@ML), MPEG-2 (MP@HL), MPEG4 AVC/H.264, HP@L4
• 2 SCARTS for TV, VCR (optional)
• 16 Bit Colors Graphic User Interface
• Multi-language Menu
• 13-digit VFD (Time clock in Stand-by mode)
• OSD Teletext Supported
• EPG (Electronic Program Guide) for On-screen Channel Information
• Installation by Easy Setup Guide
• 10,000 Channels
• User-friendly Data Editing Function
• Favorite Channel and Parental Lock Function
• RS232C Port for Additional Information Service and Upgrading System Software
• S/PDIF OUT Optical and Coaxial
• HDMI
• SVIDEO OUT
•
PVR Ready
•
Time-Shift
•
Unicable
•
Ethernet PortOptional)
•
USB Port
•
2 Common Interface and 2 Smart card Reader
•
Blind scanning function
Accessories
• User’s Manual
• Remote Control Unit
• Batteries
• HDMI Cable (Optional)
1
2
3
4
5
8
9
10
1 1
12
13
14
6
7
Chapter 2 >> Controls and Functions
5
English
C
ontrols and Functions
Front Panel
1
Power ( ) button
Turns your receiver On/Off.
2
Arrow (◄/►)buttons
Adjusts the volume and moves the cursor
left/right on the menu
3
Arrow (▲/▼)buttons
Changes channels or moves the cursor
up/down on the menu.
4
MENU button
Displays the menu
Exits from the current menu or goes to the
previous menu
5
OK button
Conrms selection
6
DISPLAY
Displays channel information
Displays local time in Standby mode
Rear Panel
1
RF IN
It Connects to the Cable antenna for DTV
signal.
2
LOOP
Loop out is an output port of the DISH
INPUT signal.
3
USB
Connects to the External HDD or USB
storage with USB cable.
4
RS-232C
Connect to a PC.
RS232 transfers data to the external
computer.
5
e-SATA
Connects to the External HDD with SATA
cable.
6
VIDEO OUT
Connects to video input jack on TV or any
external Video system.
7
AUDIO OUT, LEFT / RIGHT
Connects to audio input jacks on TV or any
external audio system.
8
Y Pb Pr OUT
Connects to video input jack on TV or any
external Video system.
9
S-Video OUT
Connects to the TV with S-Video cable
10
S/PDIF OUT Optical & Coaxial
Connects to a digital audio component with
optical cable.
1 1
Ethernet(Optional)
Connects to the Ethernet with Ethernet cable
12
HDMI
Connects to the TV with HDMI cable
13
SCART for VCR
Connects to the VCR(AUX) with SCART
cables.
14
SCART for TV
Connects to the TV with SCART cables.
Chapter 2 >> Controls and Functions
6English
Remote Control Unit
1
Power ( ) button for TV & STB
Turns your receiver & TV On/Off.
2
Numeric (0~9) buttons
Controls the number entry and changes
program channel directly.
3
Mode ( ) button
Switches between TV and Radio channel list.
4
Sleep ( ) button
Shows the time setting for the sleep-timer.
5
MoSAic ( ) button
Displays multi picture section.
6
Arrow (◄/►)or OK buttons
Adjusts the volume level or moves the
cursor left or right on the menu.
Arrow (▲/▼)or OK buttons
Changes channels or moves the cursor up
or down on the menu.
7
Menu ( ) button
Displays the menu
Exits from the current menu or goes to the
previous menu.
8
Mute ( ) button
Mutes audio output.
9
Last button
Shows Viewed Channel List.
10
Audio ( ) button
Shows the Input Audio information.
1 1
OK button
Shows Channel list while watching TV or
listening to the Radio.
12
Guide ( ) button
Shows the TV program guide.
13
VOL +/- buttons
Adjusts the volume level.
14
Zoom ( ) button
Zooms in the selected screen.
The Zooming location changes by pressing
direction buttons. (x2 → normal)
15
Text ( ) button
Changes to the teletext mode.
16
INFO ( ) button
Displays program information in the
screen.
17
Back ( ) button
Goes to previous menu. The changed
values are to be saved.
18
SAT ( ) button
Shows satellite channel list.
19
PR +/- buttons
Changes channel up or down.
20
Page (+/-) buttons
Moves up or down pages on the menu and
TV/Radio List.
21
FAV (♥) button
Go to the last channel you’ve watched in
the Favorite Channel List 1.
And if pressed angina, you can see the last
channel you’ve watched in the next Favorite
Channel List2. Repeat pressing the button
until no more Favorite Channel is found.
Then it returns to the current channel.
22
REW button
Rewinds the recorded programs to x8.
23
Play button
Play the recorder programs
Shows the recorded program in the media
player.
24
FWD button
Fast forward the recorded program to x16.
25
Record button
Starts to record programs.
26
Stop button
Stops to record the program and to play
the program.
27
Pause button
Pauses and play the program.
28
F1 button
Set the Video format.
Chapter 2 >> Controls and Functions
7
English
29
F2 button
Shows Media Player.
30
F3 button
Starts Time shift function.
31
Additional function
1. Learning Method
• If there is no further action within 30
seconds in LEARN MODE, the remote
control turns to normal operation mode
switching LED off.
• TV Power key doesn’t have Default key
data.
The Learning Method
• Only the key of “TV Power”has Learning
function.
• Toggle Learning (Continuous 2 codes
should be learned in TV Power key)
• 1st Learned data is produced upon 1st
press and then 2nd Learned data will be
produced upon next pressing on the TV
Power key.
If you press [TV Power + OK] KEYs
at the same time for 1.5 seconds, the
remote goes into leaning mode. => Then
LED ON will be “ON’ for 30 seconds.
If there is no further action, it will
automatically turn back to normal mode
after 30 seconds switching LED off.
Press TV Power key one more time. LED
blinks one time and then LED will be “ON”.
Press 1st SOURCE KEY (Power key of
the original key)
If it learns correctly, --- LED will be
“ON”after blinking Two Times.
- If it does not learn correctly, --- LED
will be “ON” after blinking 5 Times
- If there is no input Signal for 30
seconds, the remote will stay in
learning mode after blinking 5 times.
- If no further input signal for another
30 seconds, the remote will return to
normal operation mode. LED will be
OFF.
- If you want to teach it again, then you
need to press TV Power key. --- LED
will stay “ON”after blinking one time.
Now you learned one code from your
original TV power key. Please press TV
Power key one more time. --- LED will
stay ON after blinking one time.
=> If the rst TV Power code is learned
correctly (after LED Blinking two times),
2nd code can be taught.
Please press 2nd SOURCE KEY(Any
numeric key from the original remote
control. For example Number 1)
If it learns correctly, --- LED will be “ON”
after blinking Two Times.
If it does not learn correctly, --- LED will
be “ON” after blinking 5 Times
=> If there is no input Signal for 30
seconds, the remote will stay in learning
mode after blinking 5 times.
If no further input signal for another 30
seconds, the remote will return to normal
operation mode. LED will be OFF.
=> If you want to teach it again, then you
need to press TV Power key. --- LED will
stay “ON” after blinking one time.
If you press [TV Power + OK] Keys at
the same time, it turns back to normal
operation mode after LED blinking 3
times.
2. Low Battery Warning Function
It is the fuction to check if the battery has
LOW VOLTAGE
If you press [STB Power] KEY at the
level that IC’s OPERATING VOLTAGE is
as low as “2.2V ~ 2.3V”, power code will
be produced blinking LED 3 times.
At that LOW VOLTAGE level, you can
not go into LEARNING MODE.
Chapter 3 >> Connections
8English
C
onnections
Location of your receiver
• Install your receiver in horizontal position
• Do not put any heavy stuff such as a TV on your receiver
• Do not install your receiver in the places as follows: Vibrating place, direct sunrays, Humid
place, too high or low temperature, and no ventilated place.
Connecting your receiver with dish system
After installing your antenna system, connect the coaxial cable from the LNB of your antenna to
“DISH INPUT” terminal marked at the rear panel of your receiver. All cable connectors should
be nger-tightened; do not use any kind of wrench while tightening connectors. The cable
should be 75 ohm impedance coaxial twisted at the end with an “F” type connector.
Loop through
Chapter 3 >> Connections
9
English
Connecting your analog receiver
To facilitate the user using analog receiver to view analog channels, this product has been
provided with a loop through terminal marked as “Loop”. Connect the coaxial cable from this
terminal to the IF input terminal of your analog receiver. Now by keeping your receiver in
standby, you will be able to tune and view analog channels from your analog receiver.
Connecting your receiver to TV
To connect your receiver with your television, you can use 4 different methods; via RCA cable,
SCART cable, HDMI cable or YUV.
Connect the RF cable to the terminal marked “RF OUT” on the rear panel of your receiver and
its other end to the TV RF input socket.
Connect the Video/Audio RCA cables from the Video OUT/AUDIO OUT (LEFT, RIGHT) on the
rear of your receiver to the Video INPUT/AUDIO INPUT (LEFT, RIGHT) jacks on the TV. In the
case of connecting your TV through SCART cable, connect the SCART connector marked TV to
the respective SCART port on the TV. (depend on model)
Connect the HDMI cable to the terminal marked “HDMI” on the rear panel of your receiver
and its other end to the TV HDMI input.
Connecting your receiver to VCR (depending on model)
To connect a VCR, your receiver has been provided with SCART at the rear marked “VCR”.
Using a SCART connector, the VCR can be connected to your receiver.
Connecting external audio/Hi-Fi system
To connect any external Audio Hi-Fi system, your receiver has been provided with two RCA
connectors at the rear panel of your receiver, marked with AUDIO L and R respectively to
connect the left and right Audio on the external audio/Hi-Fi system.
Connecting digital audio system
Connect a cable between S/PDIF OUT at the rear panel of your receiver and S/PDIF INPUT
COAXIAL or OPTICAL on the Digital Audio System.
Chapter 4 >> Initial Settings and Operations
10 English
I
nitial Settings and Operations
Menu Information
A menu is a eld of text shown on the TV screen. Selectable lines are generally activated
(highlighted). No-activated lines cannot be selected. Most of menus show short information at
the bottom of the screen.
This menu consists of 7 main menus:
• Installation • Game
• System Setup • Multimedia
• Channel Setup • Conditional Access
• Parental Lock
1 Using the Arrow (▲/▼)buttons you can move upwards and downwards on the menus.
On the menus, you can search channels using this button.
2When you have reached the required subject menu, press the OK button to conrm your
choice.
3On the menus, you can select menu items using the Arrow (◄/►)buttons.
4When you want to return to the previous menu with saving the change, press the Back ( )
button.
5When you want to exit from the current menu, press the Menu ( )button.
Getting Started
To start your receiver for the rst time, you must select the language for displaying menus
and you should set parameters for system conguration and scan satellite channels. Perform
the following setup procedure for scanning the satellite. Follow the instructions below to scan
satellite channels. You can enjoy watching TV or listening to the Radio after the procedure
completes.
1 Turn on your TV and receiver.
Language Setting menu will appear automatically.
OSD Language is highlighted.
Selecting the On Screen Display (OSD)
Language
2Select the OSD language of your choice using the Arrow
(◄/►)buttons.
You will see the selected language on the OSD menu.
3Select Installation using the Arrow (◄/►)buttons.
Chapter 4 >> Initial Settings and Operations
11
English
Basic Operation
This section explains various functions while watching TV or listening to the Radio.
Switching Channel
You can switch the current channel by three different methods.
• Method 1: Press the Arrow (▲/▼)buttons or PR+/- buttons.
• Method 2: To select a channel directly, select a channel using the Numeric (0~9) button.
• Method 3:
1To display the channel list, press the OK button.
2Select a channel you want to watch using the Arrow (▲/▼)buttons and then press the OK
button.
• If there are multiple channels, use the Page (+/-) or the Arrow (◄/►)buttons to move to
channels by page.
• Press the Mode ( ) button to switch between the TV and Radio channel.
• Method 4: In case of more than two scanned satellites
1Press the SAT( ) button to show satellite list.
2Move the cursor to the satellite of a channel to watch with the Arrow (◄/►)buttons and
then press OK button.
3You can follow the method 3 instruction for channel selection.
• Method 5: How to move to the watched channel.
1Press the last button with RCU.
2Press OK button after a channel selection by using the Arrow (▲/▼) with RCU.
3Press OK button to exit.
Volume Control
To control the volume:
• Press the VOL+/- or the Arrow (◄/►)buttons.
• Press the Mute ( )button to turn the sound off.
• Press the Mute ( )button again or the VOL+/- or Arrow (◄/►)buttons to cancel muting.
Tabla de contenidos
Otros manuales de Receptor de Vantage Hearth
