Vanco EVMX4016 Manual de usuario
Vanco Part Number
EVMX4016
HDBaseT 16x16
Matrix Selector Switch
(230ft/70m)
www.vanco1.com • 800.626.6445
HDBaseT™ 16x16
MATRIX SELECTOR SWITCH
(230ft/70m)
www.vanco1.com 800.626.6445
2
1. Do not expose this unit to water,
moisture, or excessive humidity.
2. Do not install or place this unit
in a built-in cabinet, or other
conned space without adequate
ventilation.
3. To prevent risk of electrical shock
or re hazard, due to overheating
do not obstruct unit’s ventilation
openings.
4. Do not install near any source of
heat, including other units that
may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening
storms or when not used for
an extended period of time.
A surge protector is strongly
recommended.
8. Protect the power cord from
being walked on or pinched,
particularly at the plugs.
9. Use unit only with accessories
specied by the manufacturer.
10. Refer all servicing to qualied
personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal
and the same video resolution and audio settings on all electronic equipment in the
system. When there are multiple sources and displays, the video resolution and
audio setting on all connected units must be adjusted to correspond with that of the
display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting,
operating or adjusting this product. Please keep this
manual for future reference.
This product is 100% inspected and tested in the United
States to verify HDMI performance parameters.
www.vanco1.com 800.626.6445 3
INTRODUCTION
The Evolution by Vanco EVMX4016 16X16 Matrix with HDBaseT Technology, Wide-band IR, and PoE is
an HD switching and extension system that comprises of an 16 input/16 output matrix unit. Have 16
sources displayed simultaneously on any display or have a single source duplicated on multiple displays,
exibility for the perfect solution. Features HDBaseT (70m/230ft) technology, which allows for audio,
4K 2160p/30hZ video, IR, and Power over Cable to be transferred over a single Cat5e/6/7 cable.
Extends 1080p resolutions up to 230ft (70m) over a single Cat5e/6 cable and 2160p/30hZ (4K2K)
resolutions up to 131ft (40m). Also features Power over Ethernet (PoE) Technology which transmits
power over Cat5e/6, allowing for Receiver unit to be powered without the use of a power supply. The
result is an easy and plug and play solution that allows each output with the ability to extend HDMI over
long distances in conjunction with the Evolution by Vanco HDBaseT (70m/230ft) receiver EVRX3000
(sold separately). Features additional HDMI output per HDBaseT output for exibility or mirroring
capability, able to handle up to 32 displays. With an output bandwidth of 6.75 Gbps, the EVMX4016
is capable of high denition video and multi-channel audio distribution with simple control using the front
panel or remotely via IR Receivers at display locations. Includes RS-232 connectivity for third party
integration for control and switching, as well as IP control along with LAN connectivity for IP control
and switching remotely, using a smartphone or tablet. Also features EDID management system, which
allows and encourages device communication compatibility for seamless integration. For longer length
applications with full exibility for control, the EVMX4016 is a great solution.
FEATURES
www.vanco1.com 800.626.6445
4
HDBaseT 16x16 Matrix Selector Switch (230ft/70m)
Part # EVMX4016
• Allows up to 16 HDMI sources to be distributed simultaneously to up to 16 displays
• 16 additional HDMI outputs for exibility or mirroring capability; allows for connection
of up to 32 displays or the ability to create a larger distribution system by cascading or
daisy chaining
• HDBaseT Technology that supports HDMI Deep Color, 3D, and up to 4K 2160p Ultra
High Denition resolution @30hZ
• Supports Power Over Ethernet (PoE) which integrates power into the Cat5e/Cat6
cable, requiring no power supply for Receiving unit
• Transmission Range: Extends 1080p resolutions up to 230ft (70m) over a single
Cat5e/6 cable and 2160p/30hZ (4K2K) resolutions up to 131ft (40m)
• Features EDID management which supports default HDMI EDID and has the ability to
learn the EDID of display equipment for any “handshake” issues via RS-232 connectivity
• Receivers (sold separately) feature LED indicators for clear power and video signal
selection
• HDCP Compliant
• Supports 7.1 channel digital audio
• Wideband IR pass-through (20kHz to 60 kHz)
• Choose from 5 switching modes – front panel buttons, Local remote control, RS-232
control, IR call-back (dedicated IR extension cable connected to IR extension port, and
IR emitters on sources required), and IP control utilizing smartphone or tablet via LAN
• 17.3” (440mm) W x 13.7” (349mm) H x 5.21”(31.4mm) D
www.vanco1.com 800.626.6445 5
SPECIFICATIONS
TECHNICAL SPECS
HDCP Compliance...................................................... Yes
Video Bandwidth ........................................................ Single-link 340Mhz [10.2 Gbps]
Video Support ........................................................... 480i/480p/720p/1080i/1080p @60/2160P @30
36-bit color
Audio Support ........................................................... Surround Sound (up to 7.1 ch) or stereo digital audio
ESD Protection .......................................................... [1] Human body model — ±19kV [air-gap discharge]
& ±12kV [contact discharge] [2] Core chipset — ±8kV
PCB stack-up ............................................................ 4-layer board [impedance control — differential
100Ω; single 50Ω]
IInput........................................................................ 16x HDMI / 1x RS-232 / 1x RJ-45 for IP Control /
17x IR for IR receivers
Output...................................................................... 16x RJ-45 (HDBaseT) / 16x HDMI / 17x IR for IR
blasters
HDMI connector ........................................................ Type A 19 pin female
RJ-45 connector........................................................ WE/SS 8P8C with 2 LED indicators
RS-232 connector ..................................................... DE-9 [9-pin D-sub female]
3.5mm connector ...................................................... Earphone jack for IR blaster; [All IR Out] IR signal
from all outputs; [IR1~IR8] IR control on individual source device; Earphone jack for IR receiver; [System IR]
Receives IR commands from remote control; [IR1~IR8] Receives IR commands from individual remote control
MECHANICAL SPECS
Housing .................................................................... Metal enclosure
Power supply............................................................. AC Power 100-240V
Power consumption.................................................... 120 Watts [max]
Operation temperature............................................... 32-104 degrees F
Storage temperature.................................................. -4 - 140 degrees F
Relative humidity ....................................................... 20-90% RH (no condensation)
PACKAGE CONTENTS
• (1) EVMX4016 HDBaseT 16x16 Matrix Selector Switch
• (17) IR Receiver (RX)
• (16) IR Blaster (TX)
• (1) UL AC C13 power cord
• (1) Rack-mounting ear set
• (1) Handle Bar set
• (1) Installation software CD
• (1) IR remote control
• (1) User Manual
www.vanco1.com 800.626.6445
6
1. Power Switch
2. 7-segment LED: for output 1-16 status
3. Source Status: Input source indicator LED
4. IR SENSOR: IR sensor for receiving the IR commands from IR remote
5. Push Button: Select the output and input
6. Push Button: Enter Button
7. IR Blaster 1-16: 3.5mm IR blaster socket for individual HDMI source control
8. IR Receiver 1-16: Infrared 3.5mm socket for plugging in the extension cable of IR
receiver
9. INPUT 1-16: HDMI inputs
10. Output Port 1-16: RJ-45 outputs for each output channel
11. LED Link
12. HDMI Local Loopout Port 1-16: Local loopout HDMI outputs for each output
channel
13. RS-232: RS-232 control port
14. Ethernet: Ethernet control port
15. All IR Output: 3.5mm IR blaster socket for HDMI source control on all 16 inputs
16. System IR Receiver: Ext. IR receiver
17. AC Power: 100-240V
PANEL DESCRIPTIONS
1
45
17
13
7
9
2
2
3
3
6
8
14
15
16
10
10
11
11
12
12
www.vanco1.com 800.626.6445 7
1 2 3 4 5 6
7 8
PANEL DESCRIPTIONS RECEIVER -
Part#EVRX3000 (Sold Separately)
1. 24V DC: Connect to 24V DC power supply (optional)
2. LED: Power indicator
3. HDMI OUT: Connects to an HDMI display with an HDMI male-male cable
4. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
5. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
6. Mini-USB: For rmware updates
7. LED: TX/RX link indicator
8. RJ-45: Plug in for Cat5e or Cat6 Cable
www.vanco1.com 800.626.6445
8
1. Full-HD(1080p@60)-24bit 2D & 2ch & Dolby 5.1ch
2. Full-HD(1080p@60)-24bit 2D & 7.1ch
3. Full-HD(1080p@60)-24bit 3D & 2ch
4. Full-HD(1080p@60)-24bit 3D & 7.1ch
5. HD(1080i@60)(720p@60)-24bit 2D & 2ch
6. HD(1080i@60)(720p@60)-24bit 2D & 7.1ch
7. Full-HD(1080p@60)-36bit 2D & 2ch
8. Full-HD(1080p@60)-36bit 2D & 7.1ch
9. 4k2k@30Hz 24-Bit 7.1ch
10. 4k2k@30Hz 24-Bit 2ch
EDID
EDID Settings:
There are nine embedded default EDID settings as shown below:
EDID
EDID management allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the
display and source.
The EDID learning function is only necessary whenever any display on the HDMI output port is not outputting
audio and video properly. Because the HDMI source devices and displays may have various level of capability in
playing audio and video, the general principle is that the source device will output the lowest standards in audio
format and video resolutions to be acceptable among all HDMI displays connected. In this case, a 720p stereo
HDMI signal output would be probably the safest choice. The EDID function can also force the matrix to learn
the EDID of the lowest capable HDMI display among others to make sure all displays are capable to play the
HDMI signals normally.
There are 3 methods for EDID Learning as shown below:
1. IR Remote Control: Please refer to the Operation Control - IR Remote Control
2. Software Control: Please refer to the Operation Control - Software Control through RS-232 and LAN port
3. Web Interface Control: Please refer to the Operation Control – Web Interface Control
www.vanco1.com 800.626.6445 9
OPERATION CONTROL - FRONT
PANEL
1. INPUT/OUTPUT MAPPING
• Use the “LEFT” or “RIGHT“ push button to select the output desired to switch sources
to.
• Use the “UP” or “DOWN“ push button to select the specic source.
• Press “SET” to conrm
www.vanco1.com 800.626.6445
10
OPERATION CONTROL - IR
REMOTE CONTROL
BUTTON FUNCTION
ON Power on the matrix switcher
OFF Standby mode
PRESET Preset mapping mode
SAVE Save current mapping mode
Number buttons 1-9 Select a number
+10 Select a number
To Transfer key
TAKE Trigger the previous setting
Mute Turn off/Mute the selected Output
SWITCH Begin input and output selection
DEFAULT EDID Begin default EDID selection
LEARN Begin EDID learning from one output
ALL Select all inputs or outputs
CLEAR Clear the previous IR operation procedure
STATUS Reserved
F1 Reserved
F2 Reserved
F3 Reserved
F4 Reserved
Tabla de contenidos
Otros manuales de Cambiar de Vanco
Vanco
Vanco Evolution EVSW1061 Manual de usuario
Vanco
Vanco Evolution EVSW41KVM Manual de usuario
Vanco
Vanco VPW-280794 Manual de usuario
Vanco
Vanco Evolution EVMX88PRO Manual de usuario
Vanco
Vanco Evolution EVSW4K41 Manual de usuario
Vanco
Vanco Evolution EVSW1041 Manual
Vanco
Vanco HDMX4K44 Manual de usuario
Vanco
Vanco Evolution EVSW21MV Manual
Vanco
Vanco Evolution EVMX4004 Manual de usuario
Vanco
Vanco HDMISW41 Instrucciones de instalación
Vanco
Vanco HDSW4K31 Manual de usuario
Vanco
Vanco Evolution EVSW1040 Manual de usuario
Vanco
Vanco EVMX44QI Manual de usuario
Vanco
Vanco Evolution EVMX4K04 Manual de usuario
Vanco
Vanco 280759 Manual de usuario
Vanco
Vanco EVMX4444 Manual de usuario
Vanco
Vanco Evolution EVMX44PRO Manual de usuario
Vanco
Vanco Evolution EVSW1042 Manual de usuario
Vanco
Vanco VPW-280789 Manual de usuario
Vanco
Vanco HDBT8x7 Manual de usuario
