Vanco 280564 Instrucciones de instalación

HDMI®4x4 4K2K

Compact Matrix

Selector Switch

Vanco Part Number:

280564

Technical Support

www.vanco1.com • [email protected] • 800-626-6445

www.vanco1.com 800-626-6445

1. Do not expose this unit to water, moisture,

or excessive humidity.

2. Do not install or place this unit in a built-in

cabinet, or other conned space without

adequate ventilation.

3. To prevent risk of electrical shock or re

hazard, due to overheating, do not obstruct

unit’s ventilation openings.

4. Do not install near any source of heat,

including other units that may produce heat.

5. Do not place unit near ames.

6. Only clean unit with a dry cloth.

7. Unplug unit during lightening storms, or

when not used for an extended period

of time. A surge protector is strongly

recommended.

8. Protect the power cord from being walked

on or pinched, particularly at the plugs.

9. Use unit only with accessories specied by

the manufacturer.

10. Refer all servicing to qualied personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same

video resolution and audio settings on all electronic equipment in the system. When there are multiple

sources and displays, the video resolution and audio setting on all connected units must be adjusted

to correspond with that of the display having the lowest video and audio capability.

WARNING

DEAR CUSTOMER

Thank you for purchasing this product.

For optimum performance and safety, please

read these instructions carefully before

connecting, operating or adjusting this product.

Please keep this manual for future reference.

This product is 100% inspected and tested in the United States

to verify HDMI performance parameters.

www.vanco1.com 800-626-6445 3

FEATURES

The Vanco 280564 HDMI 4x4 Compact Matrix Selector Switch allows 4 HDMI sources

to be distributed to up to 4 displays simultaneously. Have multiple sources displayed

simultaneously on any display or have a single source duplicated on multiple displays,

exibility for the perfect solution. The 280564 is capable of up to 4K2K (2160p) Ultra

High Denition resolution and HD multi-channel audio distribution with simple control

using the front panel or remotely via IR Receivers at display locations. Also features EDID

management, which allows and encourages source and display “handshake” for seamless

integration. In addition, the 280564 is also equipped with RS-232 connectivity which allows

for third party integration. For reliable, no-nonsense HDMI distribution and control on a

budget, over short distances, the 280564 Matrix Selector Switch is a great choice for any

application

HDMI® 4x4 Compact Matrix Selector Switch

Part # 280564

• Allows up to 4 HDMI sources to be distributed

simultaneously to up to 4 displays

• Ultra HD capable Matrix Switcher providing a

perfect solution for Home or Retail AV as well

as Commercial and Hospitality Installations

• Features EDID management which supports

default HDMI EDID and has the ability to

learn the EDID of display equipment for any

“handshake” issues

• HDCP Compliant

• Supports 4K2K (2160p @ 30 Hz) Ultra High

Denition Resolution

• Supports HDMI Deep Color and 3D

• Supports 7.1 channel digital audio

• Wideband bi-directional IR pass-through (IR

transmitters, IR Receivers and IR Remote

Control Included)

• Equipped with RS-232 connectivity which allows

for third party integration

• Compact design for easy installation with

rack-mounting and wall-mounting design, rack

mounting ear set included

• Power Supply: DC 12V

• Dimensions: 10.2” W x 1” H x 4.4” D

www.vanco1.com 800-626-6445

PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and make sure the following items are

contained in the shipping carton:

• (1) 280564 HDMI 4x4 Matrix Selector Switch

• (5) IR Receiver (RX)

• (4) IR Blaster (TX)

• (1) DC 12V, 2.5A power supply

• (1) Rack-mounting ear set

• (1) IR remote control

• (1) RS-232 serial cable

• (1) User Manual

SPECIFICATIONS

HDCP Compliance...................................................... Yes

Video Bandwidth ........................................................ Single-link 297MHz

Video Support ........................................................... 480i/480p/720p/1080i/1080p @60/2160p @30

48-bit color

Audio Support ........................................................... Surround Sound (up to 7.1 ch) or stereo digital audio

and L-PCM at up to 192kHz, compressed audio (IEC 61937), DSD, DST, DTS and HBR

ESD Protection .......................................................... +/- 8 kV (air-gap discharge) & +/- 4 kV (contact

discharge)

PCB stack-up ............................................................ 4 layers

Input ........................................................................ 4x HDMI / 1x RS-232 / 1x IR socket for IR receiver

Output...................................................................... 4x HDMI

HDMI connector ........................................................ Type A 19 pin female

3.5mm connector ...................................................... [System IR] Receives IR commands from remote

control

MECHANICAL SPECS

Housing .................................................................... Metal enclosure

Power Supply ............................................................ DC 12V, 2.5A

Power consumption.................................................... 20 watts (max)

Operation temperature............................................... 32~104 °F

Storage temperature.................................................. -4 ~140 °F

Relative humidity ....................................................... 20~90 % RH (no condensation)

www.vanco1.com 800-626-6445 5

PANEL DESCRIPTIONS

1. ON/OFF: Power ON/OFF switch

2. POWER: This red LED illuminates when the device is powered

3. IR EYE: IR eye which receives IR signals from included remote for matrix switching

4. OUTPUT A: Selects and displays which specic input is selected

5. OUTPUT B: Selects and displays which specic input is selected

6. OUTPUT C: Selects and displays which specic input is selected

7. OUTPUT D: Selects and displays which specic input is selected

8. INPUT PORTS: Inputs 1-4, LED light illuminates for each input when an active signal is being sent from the

source to the matrix unit

9. OUTPUT PORTS: Outputs 1-4, LED light illuminates for each output when an active display is connected to

the matrix unit

10. RS232: Port for use of PC control and EDID settings

11. 12V DC: Plug the 12V DC power supply into the unit and connect the adapter to AC wall outlet for power

12. IR EXT: Connect included IR RX receiver for extension, which receives IR signals from included remote for

matrix switching

13. IR IN: Connect included IR RX pigtails, to be used at each display for matrix switching control and source

control

14. IR OUT: Connect included IR TX pigtails, to be used at each source for source control

15. EDID Selector: Select HDMI output signal format via EDID Selector (located on the right side panel)

1 2 3 4 6

8910

5 7

13 14

www.vanco1.com 800-626-6445

EDID

The EDID switch allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the

display and source.

The EDID learning function is only necessary whenever any display on the HDMI output port is not outputting

audio and video properly. Because the HDMI source devices and displays may have various level of capability in

playing audio and video, the general principle is that the source device will output the lowest standards in audio

format and video resolutions to be acceptable among all HDMI displays connected. In this case, a 720p stereo

HDMI signal output would be probably the safest choice. The EDID function can also force the matrix to learn

the EDID of the lowest capable HDMI display among others to make sure all displays are capable to play the

HDMI signals normally.

There are two methods for EDID Learning as shown below:

1. EDID Dip Switch Adjustment: Please see below for EDID settings via EDID Dip Switch

2. IR Remote Control: Please see below for OPERATION CONTROL – SOFTWARE CONTROL THROUGH RS-

232

EDID Dip Switch Adjustment

To adjust EDID via Dip Switch, power off matrix unit and adjust to desired EDID setting on dip switch, then

power the matrix unit on. There will be an audible beep sound conrming the changes.

EDID Settings:

There are 16 embedded default EDID settings as shown below:

Number EDID Selector EDID Description

1 0000 Auto mode (default)

2 0001 1080i,Stereo Audio 2.0

3 0010 1080i,Dolby/DTS 5.1

4 0011 1080i,HD Audio 7.1

5 0100 1080p,Stereo Audio 2.0

6 0101 1080p,Dolby/DTS 5.1

7 0110 1080p,HD Audio 7.1

8 0111 3D,Stereo Audio 2.0

9 1000 3D,Dolby/DTS 5.1

10 1001 3D,HD Audio 7.1

11 1010 2160p @ 30hz,Stereo Audio 2.0

12 1011 2160p @ 30hz,Dolby/DTS 5.1

13 1100 2160p @ 30hz,HD Audio 7.1

14 1101 1024x768 DVI

15 1110 1920x1080 DVI

16 1111 PC Software control mode

www.vanco1.com 800-626-6445 7

OPERATION CONTROL - IR REMOTE CONTROL

OUTPUT A: Pressing the 1\2\3\4 buttons will select input source to HDMI OUTPUT A,

the LED will indicate the corresponding input source.

OUTPUT B: Pressing the 1\2\3\4 buttons will select input source to HDMI OUTPUT B,

the LED will indicate the corresponding input source.

OUTPUT C: Pressing the 1\2\3\4 buttons will select input source to HDMI OUTPUT C,

the LED will indicate the corresponding input source.

OUTPUT D: Pressing the 1\2\3\4 buttons will select input source to HDMI OUTPUT D,

the LED will indicate the corresponding input source.

OPERATION CONTROL - SOFTWARE CONTROL THROUGH

RS-232 OR TCP/IP

1. System Requirement

1) OS Information: MS WinXP/7

2) Baud rates: 9600

3) Software size: 3 MB

4) Minimum RAM requirement: 256 MB

Installation:

• Connect the PC and Matrix unit via the supplied RS-232 cable (Female to Female cable)

• Power up Matrix unit

• Double click MatrixController.exe icon to run it

www.vanco1.com 800-626-6445

OPERATION CONTROL - SOFTWARE CONTROL THROUGH

RS-232

1. Controlling the Matrix unit

1. Select RS232 COM or TCP mode

2. Select RS232 COM port

3. Click to connect or disconnect PC and Matrix

4. Select Matrix IP

5. Connect to Matrix IP

6. Search Matrix IP

7. Congure Matrix IP and MAC

8. Enable or disable IR beep audible sound

9. Device information display area

10. Click to refresh device status: include device information displayed in #9 area and Input/Output Settings

on “Matrix” page

Congure TCP

After action #7 the following edit form will display shown below:

1. Select auto or static IP

2. Rewrite the Matrix IP

3. Rewrite the Matrix MAC

www.vanco1.com 800-626-6445 9

2. EDID

1. Set EDID mode for selected Input port or All Input ports, click “Set” button to complete action

2. Select EDID setting desired

3. Select Input port

4. Copy EDID from Output port to selected Input port or All Input ports, click “Set” button to complete action.

5. Select Output port

6. Download EDID content to selected Input port or All Input ports, click “Download” button to complete

action.

7. Open EDID binary le

8. Display EDID binary le path

www.vanco1.com 800-626-6445

3. Matrix Switching Control via Software

1. Displays which Input is selected for respective Output

2. Click to select Input for respective Output

3. Click to select previous or next Input for respective Output

Tabla de contenidos

Otros manuales de Conmutador de matriz de Vanco

Vanco

Vanco Evolution EVMX44SL Manual de usuario

Vanco

Vanco Evolution EVMX4K44 Manual de usuario

Vanco

Vanco VPW-280781 Manual de usuario

Vanco

Vanco Evolution EVMX4K08 Manual de usuario

Vanco

Vanco 4x3 HDBaseT Instrucciones de instalación

Vanco

Vanco Evolution EVMX4442 Manual de usuario

Vanco

Vanco 281442 Manual de usuario

Vanco

Vanco EVOLUTION EVMX42MV Manual de usuario

Vanco

Vanco VPW-280799 Manual de usuario

Vanco

Vanco 280719 Manual de usuario

Vanco

Vanco Evolution EVMX4008 Manual de usuario

Vanco

Vanco 280568 Manual de usuario

Vanco

Vanco Evolution EVMX4K16 Manual de usuario

Vanco

Vanco Evolution EVMX4K42 Manual de usuario

Vanco

Vanco Evolution EVMX4044 Instrucciones de uso

Vanco

Vanco 280688 Manual de usuario

Vanco

Vanco EVMX4X3 Manual de usuario

Vanco

Vanco HDBaseT Lite Manual de usuario

Vanco

Vanco VPW-280795 Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas