VADO STRA-149RRK-CP Manual de usuario

Thermostatic shower valve with rigid riser and shelf

STRA-149RRK-CP

Keep for future reference

Installation Guide

where inspiration flows

Vado

Wedmore Road, Cheddar, Somerset, England BS27 3EB

tel 01934 744466. fax 01934 744345

aftersales@vado.com

www.vado.com

This instruction booklet covers model:

STRA-149RRK-CP.

Version 1, 1-3-18

Please read these instructions carefully before starting installation and keep for

future reference.

Remove all packaging and check the product for missing parts or damage before

starting installation.

Any alterations made to this product and fittings may infringe water regulations and

will invalidate the guarantee.

The installation must comply with all Local/National Water Supply Authority

Regulations/Byelaws and Building and Plumbing Regulations.

To be installed in accordance with BS EN806.

We strongly recommend that you use a qualified and registered plumber.

General installation

Important - please read

This fitting is a mixing device and therefore water supplies should be reasonably

balanced.

When installed, the fitting must comply with the requirements of the Water Supply

(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

For further information, contact the Water Regulations department of your local water

supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations

Advisory Scheme by email (info@wras.co.uk) or telephone: 01495848454.

Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed

to remove debris. Failure to do so could result in damage or low flow from the mixer

unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.

The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.

Please take great care when installing this mixer not to damage its surface.

Please note if installing in an enclosed environment, access should be left for servicing

and maintenance. No costs relating to inadequate access can be accepted.

Operating Specifications

Operating Pressure

Minimum operating pressure 1 bar

Maximum operating pressure 5 bar

Contents of Packaging

Installation guide &

User manual Wall bracketRiser bracket

Thermostatic shower valve with rigid riser

STRA-149RRK-CP

Installation Guide

WHERE

INSPIRATION

FLOWS

STRATA

Thermostatic shower valve with rigid riser and shelf

User Guide

Please leave with the end-user

Accessory box 1

Accessory box 2

Valve

Quick t connectors

Screws

x 9

Wall plugs

x 9

Hex keyFilter/washers

4 5

Contents of Packaging

Handset

Riser

Shower hose with 2 washers

Shower head with washer

Riser arm

Dimensions

456mm

151mm383mm

15mm

30mm

60mm

1067mm

711mm

250mm

Installation - Quick guide

1 2

150mm

4 5

x 2

Installation - Quick guide

8 9

Installation - Quick guide

138

Installation - Quick guide

127

14 15

1110

Installation

Filter/washer

Olive

Nut

Place a rubber filter/washer in each of the locking nuts on the valve and screw onto

the connectors.

Slide on the olive, screw on and tighten

the nut.

Before installation flush through the

pipe work to ensure removal of debris,

turn off the water supply.

Locking nuts

Installation

Note: Make sure that the valve is

positioned to allow room for the riser

rail to be fitted later (see dimensions on

page 6).

Prepare the wall with 2 copper pipes

at 150mm centres, making sure both

pipes are level. Connect the water

supply to the inlet pipes. The hot water

should be connected to the left hand

pipe.

Wall plugs

150mm

Screws

Warning! Please check for any

hidden cables and pipes before drilling

holes in the wall.

Remove the nut and olive from the

connector.

Drill the 4 marked holes to a suitable

depth for the wall plugs and secure with

supplied screws. Repeat for the other

connector.

Position the valve making sure it is

level. From below mark the position of

each connector. Remove the valve, and

the connectors. Place the connector

back onto the wall and mark the 4

screw holes in each connector.

Temporarily screw both quick fit

connectors onto the valve.

Installation - riser rail

Hexagonal

key

Riser

bracket

Riser

bracket

Screws

Screwdriver

Riser arm

Riser Grub screw

Riser

Push the riser onto the connection on

the top of the valve being careful not to

damage the O-rings.

Slide the riser bracket onto the top of

the riser, make sure it passes the grub

screw.

Push the riser arm into the hole in the top

of the riser being careful not to damage

the O-rings.

Using the supplied hex key tighten the

grub screws to secure the risers together.

Slide the riser bracket up so it covers the

joint in the riser.

Make sure that the joint is exactly in the

middle of the bracket and secure in place

using the two screws.

Replace the riser onto the valve.

Slide the riser bracket into the wall

bracket.

Secure riser in position using the grub

screw on the underside of the bracket.

Finally tighten the grub screw to secure

the riser to the valve.

Installation

Hex key

Screw

Wall bracket

Wall plug

Warning! Please check for any

hidden cables and pipes before drilling

holes in the wall.

Place the bracket within the marked

position and mark the centre of the hole.

Drill the marked hole to a suitable depth

for the wall plug and secure with supplied

screw.

Riser

Make sure that the riser is vertical and

mark around the wall bracket with a

pencil.

Washer

Hose

Handset

Installation - Shower hose

Washer

Hose

Shower head Washer

Shower head

Make sure there is a rubber washer in

place in the shower head and screw onto

the riser arm.

Handset

Place one of the rubber washer into the

cone end of the hose and screw to the

handset.

Valve

Place the second rubber washer into the

nut end of the hose and attach it to the

valve outlet.

Commissioning

The valve has been factory set under balance pressures and hot water supply at 65°C.

When your specific operating conditions are significantly different from the above, the

temperature of the water may vary from the setting.

When the difference is too great, you can adjust the calibration of the valve to suit

individual requirements of the installation:

1. Check the temperature of the water being delivered from the outlet with a

thermometer.

Note: temperature readings should be taken at normal flow rate after allowing for the

system to stabilise.

2. If the temperature is not 38°C proceed to reset the calibration as follows.

Remove the handle.

Ensure the step on the stop ring is located at 12 o'clock.

Do not remove the plastic stop ring. Turn the spline of the thermostatic valve clockwise

to decrease the temperature and anti-clockwise to increase the temperature until 38°C

is achieved at outlet.

Note: the sensing part of the thermometer probe must be fully submerged in the water

that is to be tested.

Replace the handle making sure that the pin is against the step.

Once the handle has been attached ensure the temperature does not exceed 46°C when

turned entirely anti-clockwise.

Your valve setting is now commissioned.

Step

Cover

Screw

Stop ring

Valve

Temperature

handle

Tabla de contenidos

Otros manuales de Accesorio de baño de VADO

VADO

VADO OMIKA OMI-133 Manual de usuario

VADO

VADO STRA-149RRK-CP Manual de usuario

VADO

VADO Axces AX-MAT-123+K-CP Manual de instrucciones

VADO

VADO AXCES METIZ AX-MET-150-CP Manual de instrucciones

VADO

VADO AXCES METIZ AX-MET-100M/CC-CP Manual de instrucciones

VADO

VADO AXCES METIZ AX-MET-137-CP Manual de usuario

VADO

VADO AXCES ASTRA AX-AST-153/CD-CP Manual de instrucciones

VADO

VADO ORA ORA-MFSRKWO-RO-CP Manual de usuario

VADO

VADO Metiz Manual de usuario

VADO

VADO BOOTH & Co BC-AXB-181-CP Manual de usuario

VADO

VADO OMIKA OMI-SFMKWO/A-CP Manual de usuario

VADO

VADO BLACK CHIC Manual de usuario

VADO

VADO Booth & Co Axbridge BC-AXB-180-CP Manual de usuario

VADO

VADO VEL-149RRK-RO-CP Manual de usuario

VADO

VADO AXCES EKKO AX-EKO-100M/CC-CP Manual de instrucciones

VADO

VADO BOOTH & Co BC-AXB-188-CP Manual de usuario

VADO

VADO AXCES AX-SIR-140/RO/DIV Manual de operación

VADO

VADO ARRONDITM Manual de usuario

VADO

VADO Axces AX-SIR-140/RO Manual de usuario

VADO

VADO AXCES IRLO AX-IRO-100M/CC-CP Manual de usuario

VADO

VADO Zoo evo magma sense life Instrucciones de instalación y funcionamiento

VADO

VADO IND-81389/RO Instrucciones de instalación y funcionamiento

VADO

VADO INDIVIDUAL Notion IND-NOT233-BRN Manual de usuario

VADO

VADO OMIKA Manual de usuario

Manuales populares de Accesorio de baño de otras marcas

DURAVIT

DURAVIT C.1 C15240 0090 Manual

Heatstore

Heatstore HSTRL500WTN Manual de usuario

Sunshower

Sunshower PURE SOLO Manual de usuario

Delabie

Delabie Delabie Sporting 714700 Manual de usuario

Kohler

Kohler K-13056 Instrucciones de montaje

ESS

ESS Container TCL-11 Manual de usuario

Mustee

Mustee 22C Manual de usuario

VITRA

VITRA V-Flow Manual de usuario

baliv

baliv DUK-80.30 T Manual de usuario

Malmet

Malmet B105BT Manual de usuario

bathstore

bathstore Transition H1690MM Guía

BELLOSTA

BELLOSTA Edward 0800/M Manual de usuario

baliv

baliv DU-5160 Manual de usuario

Franke

Franke PRTR0006 Manual de usuario

Gessi

Gessi RILIEVO 59011 Manual de usuario

noken

noken VITAE 100188525-N299998810 Manual de usuario

Allen + Roth

Allen + Roth 1142VA-30-201 Manual de usuario

Britex

Britex HBDA Manual de usuario