Vacon nxsp Manual de usuario
installation manual
for fr7-fr9
flange mounting kit
ac drives
vacon®nxs/p
2 • vacon Flange mounting kit FR7-FR9
Telephone +358-201-2121 • Fax +358-201-212 205
INDEX
1.
General .............................................................................................................................. 3
2.
Vacon Flange Mounting Kit contents.................................................................................. 4
3.
Installation......................................................................................................................... 6
3.1 FR7 ............................................................................................................................................6
3.2 FR8 ............................................................................................................................................8
3.3 FR9 ............................................................................................................................................9
4.
Mounting .......................................................................................................................... 10
5.
Information sticker .......................................................................................................... 11
Document code: DPD01880A
Date: 5/12/2016
Flange mounting kit FR7-FR9 vacon • 3
24-hour service +358-40-8371 150 • Email [email protected]
1
1.
GENERAL
Using the Vacon Flange Mounting Kit, you can mount your Vacon NX frequency converter through the
cabinet wall so that the control unit of the drive remains inside the cabinet.
The correct installation of the Flange Mounting Kit affects the IP protection class of the frequency
converter. After the installation, the control unit is protected according to IP21 and the power unit
according to IP54 (unless the frequency converter was originally IP21-protected). See figure below.
According to standard IEC 60529 (EN 60529), the IP54 frequency converter enclosure provides
protection against dust and water sprayed from all directions. Limited ingress of both is permitted.
Cabinet
IP54
IP21
4 • vacon Flange mounting kit FR7-FR9
Telephone +358-201-2121 • Fax +358-201-212 205
2
2.
VACON FLANGE MOUNTING KIT CONTENTS
The contents of the Flange Mounting Kits for different frames are shown in the following pictures.
FR7:
1Flange, top
2Flange, bottom
3Flange, side
4Screws (5*10 TF)
5Screws (5*10 TX)
6Screws (5*8 TX)
7Sealing tape
1
2
3
3
5
6
7
5
4
Flange mounting kit FR7-FR9 vacon • 5
24-hour service +358-40-8371 150 • Email [email protected]
2
FR8:
1 Flange, top
2 Flange, bottom
3 Flange, side
4 Screws (4*8)
5 Sealing tape
FR9:
1 Flange, top
2 Flange, bottom
3 Flange, side
4 Screws (6*10)
5 Sealing tape
1
2
3
3
4
5
1
2
5
3
3
4
4
6 • vacon Flange mounting kit FR7-FR9
Telephone +358-201-2121 • Fax +358-201-212 205
3
3.
INSTALLATION
These instructions guide you through the installation of the Flange Mounting Kit that you have
purchased for your FR7, FR8 or FR9 size frequency converter.
Note:
The sealant to be used in the flange mounting kit installation is flame retardant silicone
sealant (e.g. Sika Firesil -N)
3.1
FR7
1. Remove the three screws from
both sides of the frequency
converter.
2. Remove also three screws from the
top of the frequency converter
3. Attach the side flange to both sides
with 5x10 Torx screws
4. Attach the top flange with three
5x8 Torx screws.
5. Seal the two holes and the
sides in the bottom of the
frequency converter
.
6. Fix the cable entry flange to
its place. Attach first the screws
(5x10 TF) in the upper corners
.
7. Seal the bottom flange.
8. Attach the bottom flange. Fasten
first only the two screws (5x10 TF)
in the middle
9. Seal the sides of the cable entry
flange. Then attach the two
remaining screws (5x10 TF).
Flange mounting kit FR7-FR9 vacon • 7
24-hour service +358-40-8371 150 • Email [email protected]
3
7. Seal the sides of the frequency
converter.
8. Seal the top flange.
9. Seal the small seams in each
corner.
10. Smoothen all sealed seams
with your finger. Tip your finger in
soap water before smoothening the
seams.
8 • vacon Flange mounting kit FR7-FR9
Telephone +358-201-2121 • Fax +358-201-212 205
3
3.2
FR8
1. Remove these five screws from
the right side of the frequency
converter.
2. Apply sealant to the right side flange.
3. Attach the right side flange with five
screws (4x8 TF).
4. Repeat the steps 1-3 with the left
side flange. Remove also the
middle screw from this side.
5. Seal the bottom flange with
sealing tape and attach it with four
screws (4x8 TF).
6. Seal the top flange with sealant.
7. Attach the top flange with five
screws (4x8 TF). See also the next
picture.
8. Seal all seams of the top and
bottom flanges with sealant.
Flange mounting kit FR7-FR9 vacon • 9
24-hour service +358-40-8371 150 • Email [email protected]
3
3.3
FR9
1. Before attaching the side
flanges check that they are in the
correct order. If the inner hole is
not showing the flange is on the
wrong side.
2. Seal the side flanges with
sealant and attach them with 7
(6x10 TF) screws each.
3. Seal the top flange with sealant and
fasten it with four screws (6x10 TF).
4. Fasten the sides of the top
flange with two screws/side (6x10
TF).
5. Carefully seal all the seams of
the top flange with sealant.
6. Seal the bottom flange with
sealant and attach it four screws
(6x10 TF).
7. Fasten the sides of the bottom
flange with two screws/side (6x10
TF). Seal all seams as shown in
step 5.
10 • vacon Flange mounting kit FR7-FR9
Telephone +358-201-2121 • Fax +358-201-212 205
4
4.
MOUNTING
MOUNTING PROCEDURE
1. Make an opening in the cabinet door for the flange (collar) installation using the dimensions
given in Vacon NX User's manual, chapter 5.
2. Attach the sealing tape around the opening. See Figure 1 for how to bend the tape at the corners
of the opening (1) and place the tape so that it runs
inside
the screws (2).
The kit contains a greater amount of tape than what you might need. Only use such an amount of
tape required by the dimensions of the opening.
3. Fit the frequency converter in the opening.
NOTE: The frequency converter will not fit in the opening in a straight position. Tip the converter
positioning the lower end first in the opening. See Figures 4 and 5.
Fix the converter on the plane with the screws attached.
Figure 1
Figures 4 and 5.
Otros manuales para nxsp
1
Tabla de contenidos
Otros manuales de Controladores de Vacon
Vacon
Vacon 10 Manual de usuario
Vacon
Vacon 10 Manual de usuario
Vacon
Vacon 100 INDUSTRIAL Manual de usuario
Vacon
Vacon 100 INDUSTRIAL Instrucciones de uso
Vacon
Vacon 10 Manual de usuario
Vacon
Vacon NX Manual de usuario
Vacon
Vacon NX series Manual de usuario
Vacon
Vacon 20 CP/X Instrucciones de uso
Vacon
Vacon 100 INDUSTRIAL Manual de usuario
Vacon
Vacon NX6 Guía
Vacon
Vacon 20 X Manual de usuario
Vacon
Vacon nxp/c Manual de usuario
Vacon
Vacon NX Manual de usuario
Vacon
Vacon NX Active Front End Manual de usuario
Vacon
Vacon 20 Manual de usuario
Vacon
Vacon 20 Manual de usuario
Vacon
Vacon 500X Manual de usuario
Vacon
Vacon 100 INDUSTRIAL Manual de usuario
Vacon
Vacon NX series Manual de usuario
Vacon
Vacon NX Manual de usuario
