Vacmaster VOC1218PF-01 Manual de usuario

VOC1218PF

1250W

Original Instructions

18L

IPX4

20 21

14 15

16 17

210

22 23

TABLE OF CONTENTS

SECTION PAGE

Symbols......................................................................................................................................... 4

Safety Information ......................................................................................................................... 5

Unpacking and Checking Carton Contents ................................................................................... 7

Assembly....................................................................................................................................... 7

Operation ...................................................................................................................................... 8

Cleaning Articial Lawns and Outdoor Areas ................................................................................ 9

Maintenance................................................................................................................................ 10

Troubleshooting............................................................................................................................11

Technical Data ............................................................................................................................. 12

Recycling and Disposal ............................................................................................................... 12

Thank you for purchasing this Vacmaster® artical grass wet and dry vacuum cleaner. Feel

condent that with Vacmaster® you are obtaining a high-quality product that is engineered for

optimal performance. This vacuum cleaner is suitable for use with both liquids and dry materials.

FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.

SYMBOLS

Caution

Read instruction manual. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Appliance in which protection against electric shock does not rely on

basic insulation only but in which additional safety precautions are

provided, such as double insulation or reinforced insulation, there

being no provision for protective earthing or reliance upon installation

conditions.

SAFETY INFORMATION

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER.

When using the equipment, a few safety precautions must be

observed to avoid injuries and damage. Please read the complete

operating manual with due care. Keep this manual in a safe

place so that the information is always available. If you give

the equipment to any other person, give them these operating

instructions as well. We cannot accept any liability for damage or

accidents which arise due to a failure to follow these instructions

and the safety information.

• Never leave the appliance switched on unattended, if you leave

the work area, switch the appliance o󰀨 or unplug it from the

power supply.

• Do not vacuum or use this Wet and Dry vacuum cleaner near

ammable liquids, gases or explosive vapours like gasoline or

other fuels, lighter uids, cleaners, oil-based paints, natural gas,

hydrogen, or explosive dusts like coal dust, magnesium dust,

grain dust or gun power. Sparks inside the motor can ignite

ammable vapours or dust.

• This vacuum cleaner is not suitable for the vacuuming of

asbestos or asbestos dust.

• Do not vacuum anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• Ensure the hose and connections are always pointed away from

the users face, hair, ears and eyes during operation and never

direct the nozzle towards persons or animals.

• Clear the working area of any items or precessions that you do

not wish to be vacuumed before operation.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on the cord. To unplug, grasp the plug,

not the cord.

• Do not use with damaged cord, plug or other parts.

• Do not pull or carry by cord, use cord as handle, close a door on

cord, or pull cord around sharp edges or corners.

• Do not handle the plug or vacuum cleaner with wet hands.

• To reduce the risk of health hazards from vapours or dusts, do

not vacuum toxic materials.

• Frequently check that the oat valve positioned underneath the

motor is able to move freely.

• Do not use or store near hazardous materials.

• Do not use this vacuum cleaner with a torn lter or without the

lter installed.

• Do not allow to be used as a toy. Close attention is necessary

when used by or near children.

• To reduce the risk of injury from accidental starting, unplug

power cord before changing or cleaning lter.

• Unplug from power supply when not in use and before carrying

out maintenance.

• Do not cover the ventilation openings. Do not vacuum with any

ventilation openings blocked; keep free of dust, lint, hair or

anything that may reduce air ow.

• Keep hair, loose clothing, ngers, all parts of body away from

openings and moving parts.

• If the supply cord is damaged, it must be replaced by the

manufacturer, a qualied service agent or similarly qualied

persons in order to avoid a hazard.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understanding the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children

without supervision.

• For additional protection: It is recommended that this vacuum

cleaner can be used in conjunction with residual current device

(RCD) with a rated residual current of 30mA or less.

• If foam or liquid escapes from the machine, switch o󰀨 immediately.

• Check the oat valve regularly for moving freely and examine it

for signs of damage.

When using as blower:

• Direct air discharge only at work area.

• Do not use Wet/Dry Vacuum as a sprayer.

• Do not direct air at bystanders.

• Keep children away when blowing.

• Wear safety goggles.

UNPACKING AND CHECKING CARTON

CONTENTS

1Power Head 9Carry Handle 17

Nylon Pre-lter (pre-installed)

2Hose Storage 10 Blower Port 18 Articial Grass Tool

3 Latch 11 Power Cord Storage Hook 19 Hard Floor Tool

4 Accessory Storage 12 Floor Head Holder 20 Brass Moss Removal Brush

5 Caster 13 Extension Wand (x3) 21 Round Brush

6 Container 14 Suction Hose 22 Filter Retainer (pre-installed)

7Suction Port 15 Crevice Tool 23 Screw (x6)

8On/O󰀨 Switch 16 Washable Wet/Dry Filter

(pre-installed) 24 Instruction Manual

ASSEMBLY

NOTE: A Phillips screwdriver is required.

1) Remove all the contents from inside of the vacuum cleaner container.

2) Attach the carry handle into the slots located on the top of the power head. Secure them with

supplied screws (Fig. 1).

3) Turn the container upside down and insert the feet with casters into the slots and apply

pressure until they click into place. Secure them with supplied screws (Fig. 2).

4) Your vacuum cleaner comes ready for both wet and dry vacuum cleaning with the washable

cartridge lter and pre-lter pre-installed. If the cartridge lter is not installed, refer to page 8 & 9.

5) Secure the power head back on the container, using the latches. Insert the locking the end of

the hose into the suction port of the container and lock into place (Fig. 3).

6) Choose the desired accessories and/or extension wands and push t onto the hose nozzle

(Fig. 4).

Floor Nozzle Attachments

1) To remove the oor nozzle attachment, release the push clips on either side of the oor head

holder. The attachment should drop out from underneath (Fig. 5). Only one oor nozzle should

be attached at any given time.

2) To insert a new oor nozzle attachment, place one side of the attachment into the bottom of the

oor head holder and secure one clip in place. Push the other side up into place and ensure it

is securely tted into the holder (Fig. 6).

Hard Floor Nozzle:

Attachment is suitable for wet or dry suction on hard oor surfaces. Ensure the squeegee is

located towards the back of the oor head holder and brushes towards the front.

Articial Grass Tool:

Attachment is specically designed for use on articial lawns. Ensure the front lip is facing away

from the user and in the direction of vacuuming.

OPERATION

1. Switching On/O󰀨

Connect the mains plug to a suitable a power outlet.

Position Status

I on

Oo󰀨

2. Wet & Dry Vacuum Operation

WARNING: ENSURE YOU READ, UNDERSTAND AND APPLY SECTION ENTITLED

‘SAFETY INFORMATION’.

1) Verify that the washable lter and pre-lter are installed and the container latches are secured.

2) Secure the locking end of the hose into the vacuum suction port.

3) Push the desired accessories onto the hose nozzle. The air ow regulation allows you to

change vacuum cleaner suction. For best cleaning results, fully close the air ow regulation

(Fig. 7).

4) Plug the power cord into a power outlet.

5) Turn on the motor by assigning the switch to the “I” ON position.

6) Once you have completed vacuuming, switch to the “O” OFF position and unplug the power

cord from the power.

NOTE: If vacuuming a mixture of wet and dry surfaces, fully clean and dry the lter and collection

tank after each use.

Installing Cartridge lter:

WARNING: BEFORE INSTALLING, REMOVING OR CLEANING THE VACUUM

CLEANER FILTER, ENSURE THAT THE POWER CORD IS UNPLUGGED AND

SWITCHED OFF.

1) To prepare your vacuum cleaner for wet or dry vacuuming, install the cartridge lter over the

lter cage ( ①) with the at end of the lter towards the vacuum power head. Carefully push

lter until it sits ush forming a tight seal (Fig. 8).

2) Place the lter retainer cap on top of cartridge lter over the raised lip and tighten the retainer

lock clockwise to secure against the internal lter cage (Fig. 9).

3) Place the nylon pre-lter over the cartridge lter, making sure the whole lter is covered and

secure the drawstring. Replace the power head, and secure it in place (Fig. 10).

IMPORTANT: Check the lter regularly for optimal performance. An old or blocked lter will reduce

suction performance.

IMPORTANT! The vacuum cleaner is equipped with a oat valve ( ②) which is operational during

wet suction (Fig. 11). The suction power decreases when the maximum lling level is reached.

When this happens, switch the vacuum cleaner o󰀨 immediately, and empty the container.

3. Blower Operation

WARNING! KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.

WARNING! WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE

INHALED.

1) Make sure the container and any collected waste is emptied and the lter is dry before using as

a blower.

2) Insert the locking end of the hose into the blower port on the rear side of the power head (Fig. 12).

3) Turn on the motor on by turning the switch to the ‘I’ ON position.

CLEANING ARTIFICIAL LAWNS AND

OUTDOOR AREAS

1. Everyday Cleaning with Dry Suction

1) Clear large objects and debris from the lawn surface to ensure no large objects block or

damage the vacuum cleaner (Fig. 13).

2) Fit the articial grass tool attachment to the oor head holder and attach this to the end of the

extension wands and hose (Fig. 14).

NOTE:

The articial grass tool has been specially developed for cleaning long bers of articial lawns.

3) Turn the motor on by assigning the switch to the ‘I’ ON position.

2. Remove Stubborn Dirt with Wet Suction

Stubborn dirt or mud that has been compacted into the surface is easier to remove and clean if the

lawn is wet.

1) Use a hose or watering can directly onto the stubborn dirt allowing the dirt to loosen and absorb

the water (Fig. 15).

2) Using the articial grass tool, vacuum up areas to remove the dirt deep in the lawn bers.

3. Brass Round Brush for Moss and Plant Removal

Nature likes to grow back into articial lawns, moss especially likes the damp protected surface

of articial grass. The brass brush will remove the moss from the lawn, without the use of

chemicals, the brass bers are soft and gentle to surfaces compared to steel brushes.

WARNING: ALWAYS TEST THE EFFECT OF THE BRASS BRUSH IN A SMALL

AREA. CHECK THAT THE BRUSH DOES NOT DAMAGE YOUR TYPE OF ARTIFICIAL

LAWN OR YOUR TYPE OF STONE WORK BEFORE CLEANING LARGE AREAS.

1) Fit the brass round brush tool to the end of the extension wands and hose (Fig. 16).

2) Work the moss in a gentle back and forth motion. This will dislodge the roots and the moss is

collected by the vacuum cleaner.

4. Detailed Areas

For the corners around your lawn use the crevice tool.

1) Fit the crevice tool to the end of the extension wands and hose (Fig. 17).

2) Use the crevice tool for any nal spot cleaning and to reach the edges and corners of the lawn

and around any plant pots (Fig. 17).

5. Other Outdoor Areas

Use the hard oor tool for any other outdoor ooring, decking or stonework.

1) Fit the hard oor attachment to the oor head holder and attach this to the end of the extension

wands and hose (Fig. 18).

MAINTENANCE

WARNING: REMOVE THE POWERCORD FROM THE POWER SUPPLY BEFORE

CARRYING OUT ANY MAINTENANCE.

1) Keep all safety devices, air vents and the motor housing free of dirt and dust. Use a soft, dry

brush to clean the equipment regularly.

2) Clear all dirt or debris from the collection tank after each use. Allow to dry before replacing the

power head. Do not use cleaning agents or solvents; these may damage the appliance.

3) Check the hose, attachments, and power cord to verify that they have not been damaged or

any debris is trapped and blocking airow.

1. Cleaning Washable Cartridge Filter & Nylon Pre-lter

1) Remove the lter and clean by gently tapping or brushing dirt o󰀨. For optimal performance it is

recommended to replace the old lter with a new lter regularly.

2) Use a mild soap and water solution to wash cartridge lter and nylon pre-lter and rinse with

clean water. Allow the lters to air dry before re-installing (Fig. 19 & 20).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Aspiradora de Vacmaster

Vacmaster

Vacmaster VSC2501EU Manual de usuario

Vacmaster

Vacmaster VJF912PF 0201 Manual de usuario

Vacmaster

Vacmaster VDK1538SWC Manual de usuario

Vacmaster

Vacmaster CC0101 Manual de usuario

Vacmaster

Vacmaster VOM205P Manual de usuario

Vacmaster

Vacmaster VOM205P Manual de usuario

Vacmaster

Vacmaster VP321 Manual de usuario

Vacmaster

Vacmaster VQ1530SIWDC Manual de usuario

Vacmaster

Vacmaster VJE1650SW Manual de usuario

Vacmaster

Vacmaster VJC607PF 0101 Manual de usuario

Vacmaster

Vacmaster VJC507P Manual de usuario

Vacmaster

Vacmaster VH105 Manual de usuario

Vacmaster

Vacmaster VOC507S Manual de usuario

Vacmaster

Vacmaster VP205 Manual de usuario

Vacmaster

Vacmaster UC0101 Manual de usuario

Vacmaster

Vacmaster VMVK1530SIWDC Manual de usuario

Vacmaster

Vacmaster VQ1115P Manual de usuario

Vacmaster

Vacmaster VOC507PF Manual de usuario

Vacmaster

Vacmaster VK811PH Manual de usuario

Vacmaster

Vacmaster V12 Manual de usuario

Vacmaster

Vacmaster VK1520SIWC Manual de usuario

Vacmaster

Vacmaster VOC1218PF Manual de usuario

Vacmaster

Vacmaster VFB511B 0201 Manual de usuario

Vacmaster

Vacmaster VQ1420SWD Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario