V-TAC 7817 Manual de usuario
Installation Instruction
Product Code: SKU 7817
Product Description: SELF TEST-LED EMERGENCY EXIT BOX WITH ARROW UP LEGEND
Routine Testing
Specification
Testing Record
Testing should be carried out in accordance with the recommendations of BS5266 & EN50172.
1. Do not switch off unswitched mains supply after installation. If interruption is unavoidable, the batteries must be
disconnected or damage to the batteries may occur. Leave the luminaire on continuous charge for 24 hours.
2. A monthly functional test should be conducted manually.
3. Annually, a full three hour duration test should be conducted manually.
4. Batteries should be replaced when the luminaire no longer meets the 3 hours duration performance.
5. Testing is performed by interrupting the unswitched supply for the test duration manually or self-test function
complying with IEC62034.
During testing the luminaire should remain illuminated in emergency mode.
6. Ensure that the ‘charge indicator’ is ‘ON’ during ‘Charging Mode’.
If the charge indicator (LED) is unlit, this signifies a fault.
7. Replace faulty light source and batteries immediately.
To assist with this testing, a test record is included below.
To increase the chance of a fault being reported between monthly tests, it is desirable that staff are made aware
of the purpose of the indicator.
1
2
3
4
5
6
7
8
9
10
11
12
Functional/DurationMonth Year 1 Year 2 Year 3 Year 4 Year 5
Product: _______________ Location:_____________ Installation Date:____________
Emergency Power:
Viewing Distance:
EM Duration:
Charging Time:
Ambient Temp:
Emergency Mode:
Function:
Battery:
Warranty:
<4W
30M(EU ) / 24M(AU)
1H/3H/8H
24 hours
5-45°C
Maintained
Self-test
LiFePO4 3.2V 1.5Ah
4 years (battery 2 years)
420
Installation Instruction
3 4
1 2
ALWAYS SWITCH OFF THE
MAINS SUPPLY BEFORE
INSTALLATION OR SERVICING
Dimension
186mm
330mm 30mm
x3
x3
110
230
56.4
x3
5
6
8 9
7
Installation Instruction
EMERGENCY TERMINATIONS
'L' UNSWITCHED SUPPLY
'Ls' SWITCHED SUPPLY
'N' NEUTRAL
Blue (N)
Brown (L)
Brown (L)
LUMINAIRE MAINS SUPPLY 1
2
onoff
on
1 2
onoff
off onoffon
8H 3H 3H 1H
8H 3H 3H 1H
130lm80lm80lm
10lm
Duration
Downward Light
NLLs
Connect battery
to converter
Adjust lens
angle
Lens version
Closed
cover
Eco version
Pictogram Replacement
1 2
3 4
Specifications for Self Test
Function Test
The function test is carried out every month for 3 minutes. It will check the connection of battery,
battery discharging and the connection of LED module.
Duration Test
An initial duration test is carried out at first power on, but after 24 hours charging. The yearly
duration test is carried out for 3 hours on one day within the 300th day to the 365th day every
year. It will also check the connection of battery and LED module.
A bi-colour indicator will indicate the normal and abnormal status. Green is for conditions are
normal and red for the faulty conditions.
LED Colour Status
On Time
(Seconds)
Off Time
(Seconds)
Description
Green
Permanent on / / Normal status when mains connected
Slow flash 1s 1s Duration test running
Fast flash 0.2s 0.2s Function test running
Normal flash
three times only
0.5s 0.5s Time reset
Red
Permanent on / / Battery failure
Slow flash 1s 1s Lamp failure
Fast flash 0.2s 0.2s
Duration failure - the capacity of the
battery is not enough
Both Off
Off / / Emergency mode
A test switch is applied for different functions activated manually.
Duration
Function
Press for <2s
Simulate emergency mode
Press for 3-5s
Start duration test manually. The test can be aborted by pressing off (1-2s).
Press for 5-8s
Start Function test manually for 60s.
The test can be aborted by pressing off (1-2s).
Press for >10s
Time Reset
Note:
When the mains is on, the green indicator will be permanent on. It will check the connection of
battery and the connection of LED module. If it is a non-maintained fitting, the connection of LED
module no need to be checked. When the mains is off, no test will perform.
The luminaries on which we want to perform the function and duration tests must be connected
to the mains supply for at least 24 uninterrupted hours. If the mains is off during these tests, the
tests will be postponed for 3 days.
When the fault is corrected, the indicator will only be reset to its normal status after mains
reconnected or test switch pressed.
An accuracy of the timing of the test interval is ensured that it has an accuracy of ±75 s per
week. The timing function will be retained through periods of mains supply failure or interruption
for up to 7 days.
Tabla de contenidos
Otros manuales de Equipo de iluminación de V-TAC
V-TAC
V-TAC VT-10-R Manual de usuario
V-TAC
V-TAC VT-1607 Manual de usuario
V-TAC
V-TAC 80133970 Manual de usuario
V-TAC
V-TAC VT-525 Manual de usuario
V-TAC
V-TAC VT-767-2 Manual de usuario
V-TAC
V-TAC VT-11-R Manual de usuario
V-TAC
V-TAC VT-4225 Manual de usuario
V-TAC
V-TAC VT-559 Manual de usuario
V-TAC
V-TAC VT-524-S Manual de usuario
V-TAC
V-TAC VT-519-S Manual de usuario
V-TAC
V-TAC VT-1147 Manual de usuario
V-TAC
V-TAC VT-768 Manual de usuario
V-TAC
V-TAC VT-511S Manual de usuario
V-TAC
V-TAC VT-7573 Manual de usuario
V-TAC
V-TAC VT-6005 Manual de usuario
V-TAC
V-TAC VT-45010 Manual de usuario
V-TAC
V-TAC VT-7571 Manual de usuario
V-TAC
V-TAC VT-5009 Manual de usuario
V-TAC
V-TAC VT-511S Manual de usuario
V-TAC
V-TAC VT-ST42 Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
