Utilitech 00P9016 Manual de usuario

Utilitech® is a registered trademark

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 1-866-994-4148,8 a.m. –6 p.m., EST, Monday –

Thursday, 8 a.m. -5 p.m., EST, Friday.

AB14469

ITEM #0458107

SOLAR FLOODLIGHT

MODEL #00P9016

Français p. 11

Espaňol p. 21

PACKAGE CONTENTS

PART

DESCRIPTION

QUANTITY

Mounting plate

Battery

Connections

Luminous plate

Reflection cover

Glass

Sensor

*Units come already assembled

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install

the product.

WARNING

●Consult a qualified electrician if you are not certain about the installation process.

PREPARATION

Before beginning to assemble or install lighting fixture, make sure all parts are present. Compare

parts with package contents list and hardware contents list. If any part is missing or damaged, do

not attempt to assemble the product.

Estimated Assembly Time: 5 - 10 minutes (Installation time will vary depending on skill level).

Tools required for Assembly (not included): Phillips screwdriver, Drill bit.

Important instructions before usage: Charge the battery fully before first use.

The solar panel must be installed facing the sunshine (typically on the roof) with maximum

sun exposure for a minimum of 4-6 hours a day.

Try to avoid areas of shade keeping in mind that obstacles will cast shadows at different times

during the day or seasons.

The light fixture should be installed on a flat and stable surface: the higher the installation the

larger the area of illumination.

Avoid installing the light near an air conditioner, heater, or high voltage system as quick

changes in temperature may cause the motion detection system to produce false triggers and

illuminate the light needlessly.

Avoid positioning the motion sensor head towards street traffic or anywhere other movements

may trigger the light needlessly and drain the battery prematurely.

Use a soft damp cloth to periodically clean the solar panel from accumulated dust or snow.

This will help preserve the life of the battery and maximize charging efficiency.

Helpful Items (not included): step ladder.

Solar Panel

Qty. 1

Cross Screw

ST4.2x30 mm

ST0.16x1.2 in.

Qty. 7

Plastic anchors

Ø4x28 mm

Ø0.16x1.1 in.

Qty. 7

IMPORTANT SAFETY INFORMATION

Never look directly into the light or shine in another person’s eyes.

Do not expose the light to fire or intense heat.

DO NOT DISPOSE OF BATTERY IN FIRE. BATTERY MAY EXPLODE OR LEAK.

Non-rechargeable battery is not to be recharged.

Do not immerse in water.

Do not dispose the rechargeable battery in the regular waste system, waterway, stream or

any other body of water. Preserve the environment by disposing battery in accordance with

local, state, and federal regulations.

REPLACING THE BATTERY

The battery installation place is inside the mounting plate of

the light. Remove old battery and place new Li-ion

TNL-ITR18650 rechargeable battery.

For optimum performance, allow battery to charge in

full sunlight.

ASSEMBLY INSTRUCTIONS

1. Remove the mounting plate of the light by sliding in a

downward motion.

2. Using the mounting plate of the light as a template, mark

and drill the holes on the mounting surface in the desired

location with a 3/16 in. drill bit and insert plastic anchors

(CC).

Hardware Used

Plastic anchors x4

BATTERY

3. Place the mounting plate into position and secure with

cross screws (BB).

4. Slide the light onto the mounting plate.

To position head: Twist the connections (C).

5. Using the mounting plate of the solar panel (AA) as

template, mark and drill the holes on the mounting

surface in the desired location with a 3/16 in. drill bit

and insert plastic anchors (CC).

Hardware Used

ST4.2x30 Cross Screw x4

Hardware Used

Plastic anchors x3

6. Place the solar panel (AA) into position and secure

with cross screws (BB). Tilt the solar panel to an angle

similar to the pattern of the sun.

7. Completely insert the cable plug from the solar panel

(AA) into the jack located on the light.

The cord for the solar panel is 15 ft. long, 6 ft. inside

the panel, and can be pulled out if necessary.

Only use solar panels for power charging. It is not

allowed to access other external charging equipment.

IMPORTANT: The light already has waterproofing measures, so after mounting the light

fixture, there is no need to apply silicone caulking compound around the mounting plate that

meets the mounting surface.

CAUTION: Make sure motion detector head is not UPSIDE DOWN! Turn the head so the

controls face the ground. If the head is turned upside down, the motion detector can be

damaged by rain!

Hardware Used

Solar Panel x1

ST4.2x30 Cross Screw x3

OPERATING INSTRUCTIONS

PHOTOCELL

If it is the daytime, the light will not illuminate. To test the fixture,

cover the photocell with electrical tape, turn on the switch and

the light will come on. If not, wave hand in front of the sensor,

the light will illuminate. Once you confirm it can illuminate,

remove the electrical tape.

POWER SWITCH:

Press to turn on the switch of the light. The light goes into

Sensor Mode. At night, the light will illuminate about 5 ~ 90

seconds when motion is detected. If new motion is detected

during the lighting time of previous motion, the lighting time will

start to accumulate again. NOTE: If pressed again, it will turn off

the sensor, and the light will not illuminate.

Power switch

Photocell

SENSITIVITY KNOB

Turn the knob clockwise to increase the sensitivity. The

maximum sensing distance is 50 ft. Turn the knob counter

clockwise to reduce the sensitivity. The minimum sensing

distance is 26.2 ft. You can select according to your need.

Adjust the light head (pan & tilt) towards the desired coverage

area. Adjust the sensor (I) and the regulator toward the desired

coverage area: toggle the regulator up for short range and

toggle the regulator down for long range. Walk through the

entire coverage area to check for the desired response,

readjust as necessary.

TIME KNOB

Turn the knob clockwise to increase the illumination time. The

maximum time can be 90 seconds (There may be 10 seconds

error). Turn the knob counterclockwise to reduce the

illumination time. The minimum time can be 5 seconds (There

may be 2 seconds error). You can select time according to your

need.

regulator

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

The light will

not

illuminate.

1. The sensor may be detecting daylight or

other bright light source near the unit.

2. The SENSITIVITY may be set too low.

3. The battery is low or drained.

4. The solar panel plug isn't properly

connected.

5. The battery plug isn't properly connected.

1. Reposition the installation

place to avoid other lighting

source.

2. Rotate the SENSITIVITY

knob clockwise in order to

make the detector more

sensitive to motion.

3. To charge the battery fully.

4. Make sure the solar panel

plug is fully inserted.

5. Make certain the battery

plug is connected inside

the battery compartment.

The battery

does not

fully charge.

1. If there is frequent activity from dusk to

dawn or continuous overcast days, the

solar panel may not convert sufficient

ambient daylight to recharge the battery

sufficiently.

2. There is no enough sunlight.

3. There is dust and debris on the solar

panel.

4. The cable of solar panel may be

damaged.

1. Avoid unnecessary activity.

2. Reposition solar panel to

receive more sunlight.

3. Clean dust and debris from

solar panel.

4. Make sure the solar panel

cable is not damaged.

The light

stays on

continuously.

1. The SENSITIVITY may be set too high.

2. There are other movements that trigger

the light.

1. Rotate the SENSITIVITY

knob counterclockwise in

order to make the detector

less sensitive to motion.

2. Avoid other movements may

trigger the light needlessly.

Motion is not

detected

within the

coverage

area.

1. The motion is directly towards the sensor.

2. The light may install at the place near air

conditioner, central heater, or hot air flow.

3. There is dust on motion sensor lens.

1. The sensor is more sensitive

to motion which is across the

detection field than directly

towards the sensor.

2. Avoid installing the light near

such place.

3. Clean the dust on the lens.

CARE AND MAINTENANCE

This LED motion-activated light provides years maintenance-free service with no bulbs to change.

Do not touch LED or open fixture housing.

To clean, turn OFF all power to circuit and clean surfaces with a mild, non-abrasive cleaner.

It will be necessary to periodically clean the solar panel with soft wet cloth.

WARRANTY

TWO-YEAR LIMITED WARRANTY.

If this product fails due to a defect in materials or workmanship within two (2) years (excluding

battery) from the date of purchase, return it along with proof of date of purchase and it will be

replaced with the same or comparable model free of charge.

This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty

repair.

This warranty gives you specific legal rights and you may have other rights that vary from state to

state.

IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL

ORINDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS

PRODUCT.SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL ORCONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION

MAY NOT APPLY TO YOU.

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-866-994-4148, 8 a.m. - 6 p.m.,

EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

Printed in China

Utilitech & UT design® is a registered

PART

DESCRIPTION

PART#

Solar panel

458107- AA

Cross Screw

458107- BB

Plastic anchors

458107- CC

Tabla de contenidos

Idiomas:

Otros manuales de Foco de Utilitech

Utilitech

Utilitech Motion Sensing Security Light UT-9250-BZ Manual de usuario

Utilitech

Utilitech WQL500UT Manual de usuario

Utilitech

Utilitech UT-5675-BZ Manual de usuario

Utilitech

Utilitech A911Pb-D800A-WH-PK1 Manual de usuario

Utilitech

Utilitech FSI UT-201-1600BRZ Manual de usuario

Utilitech

Utilitech UT-5571-BZ Manual de usuario

Utilitech

Utilitech 6211W-PIR26B Manual de usuario

Utilitech

Utilitech A911Pb-T1200A-LBZ-PK1 Manual de usuario

Utilitech

Utilitech MSLED1801UT Manual de usuario

Utilitech

Utilitech FSS1530LPCWUT Manual de usuario

Utilitech

Utilitech TMQ150UT Manual de usuario

Utilitech

Utilitech 006220B Manual de usuario

Utilitech

Utilitech FSI UT-201-800BRZ Manual de usuario

Utilitech

Utilitech SE1048-BP2-02LF0-U Manual de usuario

Utilitech

Utilitech DUSK-TO-DAWN SE1056-WHG-01LF0-U Manual de usuario

Utilitech

Utilitech Utilitech UT-5681-BZ Manual de usuario

Utilitech

Utilitech Motion SenSing Halogen Security Light... Manual de usuario

Utilitech

Utilitech UTILITECH UT-9272-BZ Manual de usuario

Utilitech

Utilitech UT-5412 Manual de usuario

Utilitech

Utilitech #SE1019-WH3-02LF0-U Manual de usuario

Utilitech

Utilitech DualBrite UT-5512-BZ Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario