Uponor Climate Control Manual de usuario
RADIANT HEATING SYSTEMS
UPONOR CLIMATE
C O
˘NTROL™ NETWORK
SYSTEM THERMOSTAT
Uponor Climate Co
˘ntrol™ Network System
Thermostat User Manual
USER MANUAL
www.uponor-usa.com • www.uponor.ca
2
Uponor Climate Co˘ntrol™ Network System
Thermostat User Manual
Published by Uponor
5925 148th Street West
Apple Valley, MN 55124 USA
Phone: (800) 321-4739
Fax: (952) 891-2008
Uponor, Ltd.
655 Park Street
Regina, SK S4N 5N1 CANADA
Phone: (888) 994-7726
Fax: (800) 638-9517
www.uponor-usa.com
www.uponor.ca
© 2008 Uponor
All Rights Reserved.
First Edition
First Printing, April 2008
Printed in the United States of America
Uponor Climate Co˘ntrol™ Network System Thermostat User Manual i
Table of Contents
Section 1 — Uponor Climate Co˘ntrol™
Network System Thermostat . . . . . . . . . . . . . . . . . . . . . 3
Section 2 — Button Function and Operation . . . . . . . . 5
Thermostat Display . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 3 — Using the Thermostat . . . . . . . . . . . . . . . 7
Outdoor Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 7
Viewing the Room Temperature Setpoint . . . . . . . . . . . . . . . . . 7
Changing the Room Temperature Setpoint . . . . . . . . . . . . . . . . . 7
Viewing the Slab Temperature Setpoint . . . . . . . . . . . . . . . . . .7
Changing the Slab Temperature Setpoint . . . . . . . . . . . . . . . . .7
Section 4 — Selecting the Operating Mode . . . . . . . . . 9
Selecting modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Section 5 — Changing the Fan Speed . . . . . . . . . . . . 11
Section 6 — Using the Ventilation Mode . . . . . . . . . . 13
Turning Ventilation Mode On and Off. . . . . . . . . . . . . . . . . . 13
Section 7 — Changing Ventilation Fan Speed . . . . . . 15
For two-speed equipment . . . . . . . . . . . . . . . . . . . . . . 15
For three-speed equipment . . . . . . . . . . . . . . . . . . . . . 15
Section 8 — Viewing the Relative Humidity Reading . . . 17
Section 9 — Changing the Relative Humidity Setpoint . . 19
Section 10 — Changing the Units of Temperature . . . 21
Section 11 — Setting the Backlighting Time . . . . . . . 23
www.uponor-usa.com • www.uponor.ca
ii
Uponor Climate Co˘ntrol™ Network System Thermostat User Manual 3
The Uponor Climate Co˘ntrol™ Network is an integrated
system built to accommodate the vast majority of a
home’s heating, ventilation and air conditioning (HVAC)
applications. It uses a modular design to scale the system
to t any HVAC mechanical system.
This user manual provides standard operating procedures for
use with the Uponor Climate Co˘ntrol Network Thermostat.
Section 1 –
Uponor Climate Co˘ntrol™ Network System Thermostat
Following is a list of common terms used in this manual
and how they are dened for this product:
Term Denition
CO2 Sensor A carbon dioxide readings in a room.
HRV Heating-recovery ventilator
Slab This refers to a concrete slab under which radiant heating
has been installed
Setpoint This refers to the desired thermostat setting. The room
setpoint temperature is the target temperature for the room.
Zone An area of a radiant panel served by one or more loops
and individually controlled through a thermostat
Table 1-1: Terms Used in this Manual
www.uponor-usa.com • www.uponor.ca
4
Uponor Climate Co˘ntrol™ Network System Thermostat User Manual 5
Section 2 –
Button Function and Operation
The Climate Co˘ntrol Network thermostats come with
simple, easy-to-use push-buttons that allow the user to
access a variety of information and setting.
The basic button types on the thermostat are:
• Cycle button — Press the cycle button to scroll
through user settings (between setpoints and readings).
• Mode button — Press the mode button to scroll
through setup options (heat and cool mode,
schedules, etc.).
• (+) and (–) buttons — Press the + and – buttons
to change settings (setpoints, fan speeds, etc.).
Thermostat Display
The Thermostat Display consists of four elds:
• Reading — This eld displays current room temperature.
• Status — This eld shows which parts of the heating
and cooling system are currently in operation.
• System Mode — This eld displays whether the
thermostat is set to run heating, cooling, ventilation
or any combination.
• Schedule and Master — Whether the thermostat
is running a setback schedule or vacation calendar
and indicates if it is the controlling thermostat for
a given air zone.
Refer to Figures 2-2 and 2-3 to view how the elds display
on the vertical and horizontal thermostat respectively. Figure 2-1: Thermostat
Reading Field
Status Field
System Mode Field
Schedule and Master Field
Reading Field
Status Field System and
Mode Field
Schedule and Master Field
Cycle button
Mode button
Figure 2-2: Vertical Thermostat Icon Display Figure 2-3: Horizontal Thermostat Icon Display
www.uponor-usa.com • www.uponor.ca
6
Table 2-1:
Thermostat Display
Icon Descriptions
Note: All of the above icons may
not always be viewable or
displayed, depending on
how the Climate Co˘ntrol
Network-system is set up.
No. Name Description
1 Air Circulation Icon Indicates a stale air call
2 Relative Humidity Icon Indicates a humidity call
3 Forced-air Heating Icon Indicates the furnace is delivering air heat
4 Forced-air Cooling Icon Indicates the air conditioner is delivering air cooling
5 Ventilation Icon Indicates the ventilation system is running
6 Fan Icon Indicates the fan is running
7 Fan Speed Indication Icon Indicates fan speed(if multiple speed is available)
8 Ventilation Mode/
Outdoor Temperature Icon
Indicates the ventilation mode is turned on (when available);
also appears when the outdoor temperature is viewed
9 Vacation Schedule Icon Indicates that the vacation schedule is enabled
10 Character Display Displays numeric settings
Note: When temperatures are displayed in °F, only full
degree increments are available.
11 Unit Icons Displays the current units (°C or °F)
12 Slab Icon Indicates when the slab settings are viewed or modied
13 Radiant Heating Icon Indicates the radiant heating system is running
14 Supplemental Heat Icon Indicates when supplemental heating is running
(e.g., baseboard heating)
15
16
Cooling Mode Icon
Heating Mode Icon
Indicates the system is in cooling mode
Indicates the system is in heating mode
17 Master Thermostat Icon Indicates that the thermostat is designated as an air zone’s
master thermostat
18 Schedule Enabled Icon Indicates that a schedule is enabled
Figure 2-4: Thermostat Display
Each of the elds display specic
icons to show the modes and
functions of the thermostat. Refer
to Figure 2-4 and Table 2-5 for
detailed information about each icon.
Uponor Climate Co˘ntrol™ Network System Thermostat User Manual 7
Outdoor Temperature
Press the cycle button once to view the outdoor
temperature. The LCD shows both the outside temperature
and the outdoor temperature icon as shown in Figure 3-1.
Figure 3-1: Outdoor Temperature Icon
Viewing the Room
Temperature Setpoint
The thermostat displays the current room temperature
while static or while no button is pressed. The display
returns to the current room temperature after ve seconds
of the last button press.
Changing the Room
Temperature Setpoint
The room temperature setpoint is the target temperature
for the room that the thermostat controls. When viewing
the room temperature on the display, use the (+) or (–)
buttons to change the room temperature setpoint.
• Press the (+) button to increase the room temperature
setpoint by 1.0°F or 0.5°C degree increments
depending on the temperature units displayed.
• Press the (–) button to decrease the room temperature
setpoint by 1.0°F or 0.5°C degree increments
depending on the temperature units displayed.
Viewing the Slab Temperature
Note: The slab temperature readings and settings are only
available if the slab sensor is installed.
The slab temperature is the current temperature of the
radiant panel. This temperature is viewable for radiant
heating and/or radiant cooling.
To view the slab temperature, press the cycle button three
times or until the display shows the slab icon blinking.
The display now shows the temperature of the slab.
Figure 3-2: Slab Temperature Icon
Changing the Slab
Temperature Setpoint
Note: Slab temperature readings and settings are only
available if the slab sensor is installed.
The slab temperature setpoint is the target temperature
of the radiant panel. To change the slab temperature
setpoint, use the following procedure:
• Press the cycle button three times or until the
blinking slab icon appears.
• Press the (+) button to increase the slab temperature
setpoint by 1°F or 0.5°C degree increments depending
on the temperature units displayed. Press the (–)
button to decrease the slab temperature setpoint by
1°F or 0.5°C degree increments depending on the
temperature units displayed.
Section 3 –
Using the Thermostat
www.uponor-usa.com • www.uponor.ca
8
Otros manuales para Climate Control
2
Tabla de contenidos
Otros manuales de Termostato de Uponor
Uponor
Uponor T-85 Manual de usuario
Uponor
Uponor Smatrix Move PLUS Manual de usuario
Uponor
Uponor T-26 Manual de usuario
Uponor
Uponor Comfort E T-87IF Manual
Uponor
Uponor A3030101 Manual de usuario
Uponor
Uponor Ecoflex Supra Standard ETN4 Manual de usuario
Uponor
Uponor Climate Control Zoning System II Manual de usuario
Uponor
Uponor T-26 Manual de usuario
Uponor
Uponor SetPoint 521 Manual de usuario
Uponor
Uponor T-26 230 V Manual de usuario
Uponor
Uponor Smatrix Wave X-165 Manual de usuario
Uponor
Uponor A3040654 Manual de usuario
Uponor
Uponor Comfort E T-87IF Manual de usuario
Uponor
Uponor T-54 Manual de usuario
Uponor
Uponor SetPoint 521 Manual de usuario
Uponor
Uponor T-87IF Manual
Uponor
Uponor T-23 Manual de usuario
Uponor
Uponor T-26 Manual de usuario
Uponor
Uponor Comfort-E Manual de usuario
Uponor
Uponor 1121082 Instrucciones de instalación
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
