Unitech MSR206 Manual de operación y mantenimiento
MSR206
Magnetic Stripe Card Reader/Writer
(High & Low Coercivity)
Programmer’s Manual
Document PM017-U
Revision C.1
09 Oct. 2003’
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Table of Contents 2003/10/9
Page II
Total 28 pages
Table of Contents
Section 1 Introduction__________________________________________________ 1
Accessories of MSR206 ___________________________________________________ 1
Warranty ________________________________________________________________ 1
Section 2 General description ___________________________________________ 2
Section 3 Technical specifications _______________________________________ 3
Section 4 Setup _______________________________________________________ 5
Section 5 Utilities test program __________________________________________ 6
System requirement ______________________________________________________ 6
Test program installation __________________________________________________ 6
Section 6 Command and response ______________________________________ 10
Section 7 Data format _________________________________________________ 14
Section 8 Communication sequence _____________________________________ 16
8.1 MSR 206 INITIALIZATION ______________________________________________ 16
8.2 WRITE DATA TO MSR 206 _____________________________________________ 16
8.3 READ DATA TO MSR206_______________________________________________ 16
Section 9 Addendum __________________________________________________ 18
(I) WRITE DATA TO MAGNETIC CARD ______________________________________ 18
(II) WRITE RAW DATA TO MAGNECTIC CARD ________________________________ 19
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Table of Contents 2003/10/9
Page 1
Total 28 pages
Section 1 Introduction
Thank you for purchasing the MSR 206 Manual Swipe Magnetic Card Reader/Writer. It is ideal for access control, time
keeping, banking, ID recognition & credit verification and related applications. In fact, wherever a magnetic stripe ID
or transaction card is used, one can find a related use for the versatile, user-friendly MSR206 reader/writer.
The MSR 206 is designed to offer a reading and writing solution of high and/or low coercivity cards that will
attractively complement an existing system.
This manual provides detailed information about the MSR 206. For ease of installation and programming use, we have
addressed everything from its attractive features to its various configurations.
When designing the MSR 206, we selected what we feel are the most useful features and functions. If in some cases
you find that your specific needs differ from our existing products, we welcome your comments and suggestions.
Custom-designed models are also available.
This MSR206 series has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
This MSR206 series also had been tested and found to comply with the agency requirements of specification for CE
mark Class B
EN 50 082-1: 1992 EN 55 022: 1994 Class B
IEC 801-2: 1984 EN 61000-3-2: 1995 Class A
IEC 801-3: 1984 EN 61000-3-3: 1995
IEC 801-4: 1988
Accessories of MSR206
Make sure all the following accessories are contained in your package:
1. Switch power Supply, AC 110~240V in / DC 24V, 2.2A out.
2. Power cord.
3. Signal cable (DB9 to RJ45, 1.5m)
4. Utility disk (A/P S/W).
5. Blank Hi-Co test card.(or and Low-Co test card)
6. Programmer’s manual
Warranty
One year after purchase of MSR206, any alteration and/or erasure or modification of the MSR206 will void the
warranty.
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Section 3 – Technical specifications 2003/10/9
Page 2
Total 28 pages
Section 2 General description
The MSR206 series is designed to read and/or write high or low coercivity magnetic cards. It can encode and verify up
to 3 tracks of data simultaneously. It communicates with a host computer or other terminal using a standard RS-232
interface.
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Section 3 – Technical specifications 2003/10/9
Page 3
Total 28 pages
Section 3 Technical specifications
ITEM SPECIFICATION
Standard ISO7811
Electrical
Current/operating Typical 350mA Max
Consumption
600mA plus for each writing track
Communication Standard RS232 signal voltage levels. Default, 9600 Baud, None Parity, 8 bits
Power supply External switching Power 24V/2.2A regulated
Interconnection
Cable RJ45->DB9, 5 feet
1.shield
2.TXD / MSR206 data transmit
3.RXD / MSR206 data receive
4,6,7,8,9, no connection
Pin Assignment
DB-9
5. circuit ground
Mechanical
Body ABS 94V-0
Swipe Manual, single direction
Outline 210Lx68Wx60H mm
Weight 1.5Kg approx.
Environment
Operation -10ºC to 60ºC
10 to 85% humidity, non condensing
Storage -30ºC to 70ºC
10 to 90% humidity, non condensing
Performance
Track 1&3 210bpi
Read Circuit
Track 2,75 or 210 bpi
Bit per Char 5-7 bit per char.
Read, 5-50 ips (read speed 5-40 ips for track 2 at 210bpi)
Media Speed
Write, 5-30
Read 300-4000 Oe Mag. Card
MSR206-XHC write 2750-4000 Oe Mag. Card
Media Coercivity
MSR206-XHL write 300-4000 Oe Mag. Card
Media Thickness 0.76-1.2mm
Jitter Card Read bit to bit interval <+/-15% card
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Section 3 – Technical specifications 2003/10/9
Page 4
Total 28 pages
Write bit to bit interval <+/-10%,Sub interval<+/-12% at 30ips
Low amplitude Card Read 60% for both 75& 210bpi
Error Rate Read < 0.5%
Write < 0.8%
Media Swipe Head life 1,000,000 passes for both read & write head
Model Read/Write Track Hi-C Lo-C
MSR206-3HC 1,2&3 R/W R
MSR206-5HC 1&2 R/W R
MSR206-1HL 2 R/W R/W
MSR206-3HL 1,2&3 R/W R/W
Configuration
Available Model
MSR206-5HL 1&2 R/W R/W
MSR206 Programmer’s Manual UDN PM017-U Rev.C .1
Section 4 – Setup 2003/10/9
Page 5
Total 28 pages
Section 4 Setup
1. Power off your system (PC).
2. Connect PC and MSR206 as below.
3. Connect DB9 of signal cable to a free serial port then connect RJ45 at the other end of the cable to MSR206
4. Connect outer plug of Power-out cable to the power inlet of MSR206.
5. Connect Power-in cable to Power supply and AC receptacle (110V~240V).
6. Power on your system (PC).
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Section 5 – Utilities test program 2003/10/9
Page 6
Total 28 pages
Section 5 Utilities test program
Every MSR206 comes with a utilities test program disk that includes a Windows version. This program is to verify and
demonstrate the functionality of the MSR206. In some cases, it can be used as a card reading and writing program.
System requirement
a. 80286 PC/AT compatibles or later model with color display.
b. Either the following operating systems: Windows 95, Windows 98, Windows 2000, or NT4.0.
c. 256K available conventional memory.
d. A free serial port (Com 1 or Com 2) with DB9 male connector.
Test program installation
User shall follow the steps below in order to install test program
A. Connect MSR206 to RS232 port, and power on it.
B. Insert utility diskette into floppy disk drive on PC, and execute the self-extracting file (e.g.: MSR206.exe)
C. Execute test program from the subdirectory of ‘Demo AP’ (e.g. 206DDX21.exe)
D. The test program will auto-detect communication port. If there is any errors occurred, it’ll appear in the
information dialog box after opening the program. User can close the AP by pressing OK button.
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Section 5 – Utilities test program 2003/10/9
Page 7
Total 28 pages
E. If “Not Find Reader/Writer!” appears in the information dialog box after opening the program, check to see
that the DB9 connector is plugged into the correct COM port and the power cord/connector is also attached to
DB9 thus lighting the green LED on the MSR206.
F. When the test program is first opened, a password dialog box will ask whether you wish a first time password.
If yes, enter a password of one or more characters, maximum to 16 characters. And proceed to step H.
G. If a password is not required, press ESC and a dialog box will ask you to confirm that a password is not
required. Click on Yes and proceed to demo program.
H. When entering a password for the first time, the system will require you to confirm the password, Click OK,
after you reenter your password.
* Remember the password you entered, because if it is forgotten, you must re-install the Test Program.
* Remember, however; should you desire password protection in the future, you must re-install the program.
I. When the test program is opened, you’ll see the main window of the READER/WRITER UTILITY
PROGRAM.
From this main window you can activate all functions by clicking the appropriate buttons and following the on
screen instructions.
MSR206 Programmer’s Manual UDN PM017-U Rev.C.1
Section 5 – Utilities test program 2003/10/9
Page 8
Total 28 pages
J. The test program will auto detect if a MSR206 is connected.
By clicking Setup from main window, you can change COM ports, Leading Zeros for all 3 tracks and BPI of
track 2.
K. By choosing User Type from the main window, you can then define your user parameters by clicking Setup &
selecting User Type.
Otros manuales para MSR206
1
Tabla de contenidos
Otros manuales de Lector de tarjetas de Unitech
Unitech
Unitech MS242 Manual de usuario
Unitech
Unitech RP901BTF Manual de usuario
Unitech
Unitech MS242 Manual de usuario
Unitech
Unitech MSR 120 Series Hoja de especificaciones
Unitech
Unitech MS240 Manual de usuario
Unitech
Unitech MSR206 Manual de usuario
Unitech
Unitech MS240 Manual de usuario
Unitech
Unitech MS240 Manual de usuario
Unitech
Unitech MSR 120 Series Manual de operación y mantenimiento
Unitech
Unitech MSR 120 Series Hoja de especificaciones
