Unit UTD4000 Series Manual de usuario

Uni-Trend Technology (Chengdu) Ltd

Page1of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

UNI-T

Operating Manual and Installation Instructions

Document No. SYSC-

February 2009

Oscilloscope Communication & Control Software

Operating Manual

Page2of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

2. Products of the Company are protected by patents granted and pending in the

People’s Republic of China.

3. Information contained in this manual supercedes all information in previously

published versions.

4. The Company reserves the right to change specifications and prices.

Note : Uni-T is the registered trademark of Uni-Trend Technology (Dongguan) Ltd.

Uni-Trend Technology (Chengdu) Ltd

Page3of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

Table of Contents

Chapter 1 Installation of the oscilloscope communication

and control software …………………………………

1.1 Hardware requirements ………………………………………….. 4

1.2 Installing the software …………………………………………… 4

1.3 Running the software ……………………………………………. 8

1.4 Installing the USB driver ………………………………………… 9

Chapter 2 Getting to know your oscilloscope communication

and control software …………………………………

2.1 The control panel …………………………..……………………... 12

2.2 Main menu ……………………………………………..…………. 13

2.3 Control panel instructions ………………………………...………. 18

2.4 Far Control and explanatory notes ………………...….. 20

Chapter 3 Operation

uide for the oscilloscope communication

and control software …………………………………

3.1 USB interface controls ……………………………………………. 21

3.2

3.3

Ethernet (LAN) interface controls ………………………………...

GPIB interface controls …………………………………………...

Chapter 4 System Prompts and Trouble-shooting …………….. 25

4.1 System prompts …………………………………………………... 25

4.2 Troubleshooting ……………………..……………………………. 25

Uni-Trend Technology (Chengdu) Ltd

Page4of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

Chapter 1 Installation of the oscilloscope communication and

control software

1.1 Hardware requirements

Equipment requirements Minimal.

Oscilloscope UTD4000 Digital Storage Oscilloscope.

Computer Windows 2000/XP/Vista, 128 MB RAM, 16x CD-ROM or better (Vista

users please refer to its individual hardware requirements), SVGA display

or better.

Connection cable USB A-B connection cable

1.2 Installing the software

Your UTD4000 Series Digital Storage Oscilloscope (“Oscilloscope”) comes with an oscilloscope

communication and control software (contained in the CD-Rom supplied with your oscilloscope)

File name : UTD4000 Digital storage oscilloscope communication control software Operating

Manual and Installation Guide.

Installation :

Step one : Insert the CD-ROM supplied with your oscilloscope into the CD-Rom drive of the

computer. Wait for the system to read and find the oscilloscope communication and control software

contents (Fig. 1-1).

Fig1-1

Note : 1.The installation pack downloaded online must be unzipped before application.

2.The software supports Windows 2000, Windows XP and Vista operating systems. On

Vista only USB2.0 communication protocol is supported.

Step two : Double left click the mouse to run the oscilloscope communication and control

software installation as shown in Fig 1-1.

The installation wizard for the oscilloscope communication and control software will

pop up, as shown in Fig. 1-2.

Uni-Trend Technology (Chengdu) Ltd

Page5of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

Fig 1-2

Step three : Read the prompt in Fig 1-2 then click the [NEXT (N)] button to enter the next step, as

shown in Fig 1-3.

Fig 1-3

Step four : In Fig 1-3, enter your user name and company name, then click the [NEXT (N)] button

to enter the next step, as shown in Fig 1-4.

Uni-Trend Technology (Chengdu) Ltd

Page6of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

Fig 1-4

Step five : In Fig 1-4, click the [CHANGE (H) …] button to specify the installation path of the

software, then click [NEXT (N)]. You can also click [NEXT (N)] directly to use the

default path. Enter the screen shown in Fig 1-5.

Fig 1-5

Step six : In Fig 1-5, after confirming the message is correct, click [NEXT (N)] to enter the front

page for automatic installation, as shown in Fig 1-6.

Uni-Trend Technology (Chengdu) Ltd

Page7of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

Fig 1-6

Step seven : When automatic installation is complete and the box shown in Fig 1-7 pops up, click

the [FINISH (F)] button. Your oscilloscope communication and control software is

now successfully installed on your computer and ready for use.

Fig 1-7

To return to the previous installation guide interface, click [BACK (B)] on any installation guide

page.

To stop installation, press [CANCEL (C)] on any installation guide page.

Uni-Trend Technology (Chengdu) Ltd

Page8of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

1.3 Running the software

When installation of the oscilloscope communication and control software is complete, you can run it on

your computer in two ways.

1. When installation of the oscilloscope communication and control software is complete, an short-cut

icon is automatically created on the computer desktop, as shown in Fig 1-8. To run the software,

simply double left click the icon in Fig 1-8 with your mouse.

Fig 1-8

2. Alternatively, you can run the software by going through START →Programme →Digital storage

oscilloscope →DSO, as shown in Fig 1-9.

Fig 1-9

Uni-Trend Technology (Chengdu) Ltd

Page9of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

1.4 Installing the USB driver

If you are using the oscilloscope’s USB device port for software communication and control, the USB

driver must be installed after installation of the oscilloscope communication and control software is

complete. Follow the steps below :

1. There is a USB device port on the rear panel of your UTD4000 Series Digital Storage Oscilloscope.

With the supplied USB A-B cable, you can connect the USB device port to the USB Host port of the

computer and obtain power supply for the oscilloscope.

2. After checking that connection and power supply are normal, power on the digital storage

oscilloscope. When the operation status screen appears, a prompt will appear at the right bottom

corner to indicate “New hardware DSO detected”, as shown in Fig 1-10.

Fig 1-10

Next, an icon will be created for the “New hardware DSO detected”, as shown in Fig 1-11.

Fig 1-11

Then a “hardware update wizard” dialog box will pop up on the desktop, as shown in Fig 1-12.

Fig 1-12

Uni-Trend Technology (Chengdu) Ltd

Page10of27

UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide

3. In the new hardware wizard dialog box in Fig 1-12, select the “automatic software installation

(recommended) (I) option, then click [NEXT (N)] to enter the automatic driver search and

installation page, as shown in Fig 1-13.

Fig 1-13

4. As shown in Fig 1-13, the hardware installation wizard of your digital storage oscilloscope begins

automatic searching and installing the USB driver for the oscilloscope communication and control

software. When installation is complete the dialog box shown in Fig 1-14 pops up.

Fig 1-14

Uni-Trend Technology (Chengdu) Ltd

Otros manuales para UTD4000 Series

Tabla de contenidos

Otros manuales de Instrumento de medición de Unit

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario