Unique 400 Manual de usuario
USER GUIDE
Picture apliances ..................................................... 3
Before rst use ........................................................ 4
Tips for saving electrict energy ................................ 6
Important warnings .................................................. 7
Installation and connection....................................... 8
Connection to the electricity grid ..............................9
Device operation .....................................................11
Maintenance and cleaning ......................................14
Troubleshooting ......................................................17
Picture appliances
Equipment apparatus can be changed depending on the model of
the appliance.
The label with basic information about the appliance is located in
the interior or on the back of the device.
3
Before rst use
Before plugging in electrical voltage, a machine is
idle for approximately 12 hours.
This reduces the possibility of improper action due
to the impact of transport on cooling system.
Thoroughly clean the appliance, especially the interior
(Follow advice from the chapter Cleaning).
• Instructions for use are intended to,
and describe the appliance and its correct and safe
use.
• Remove the brackets and protectors of Styrofoam.
• Remove all packaging materials and adhesive tape.
• Before you remove the old cooling appliance, remove
His neck, as this will prevent the children during the
Game accidentally shut inside.
• The packaging of our products designed for the
environment harmless material, which is without risk
for the environment can be reprocessed (recycled) or
destroyed. In this regard, packaging materials
adequately labeled.
• Our guide was also printed on recycling paper, or on
paper, without Bleached chlorine.
• When the appliance is can not be used more when
you spend a bothered, make sure not to be a burden
environment.
Provide the authorized collectors of waste household
appliances (see Removing the old appliance).
• served appliance immediately remove from service.
Unpacking
Our care for the
environment
!
4
Possible to disable the lock To avoid the danger
posed to children from choking.
• Appliances containing refrigerant and insulation
ingredients that require special degradation,
thus removing appliances connect with
authorized and certied municipal
company, or contact the dealer. because
the risk of environmental pollution, be careful not to
damage the pipe in the bottom of the apparatu.
Connect the appliance to the power grid
• Insert the power cord -dovodnog cable into a
grounded outlet, which must not be placed directly
behind the camera.
• Make sure the unit is energized, and so to open
the bottom cover under the door and make sure the
display - a pointer electronic thermostat.
Set the to the desired location.
Note: The door may be about 2.5 cm
moved forward with respect to neighboring
elements.
The thermostat for selection temperature
The thermostat for temperature selection is factory
regulated.
The temperature will settle down after 24 hours.
Attention!
5
Tips for saving
electric energy
• Do not close the appliance door more frequently than necessary.
This is especially important in hot or humid weather.
• Periodically check that the camera has secured a sufcient cooling
degree (smooth air circulation behind the appliance).
• Damaged or poorly attached to seal-magnetic rubber door causes a
higher power, therefore, timely to make sure a suitable replacement.
• The condenser on the lower front side must always be clean and free
of dust or layers of dust (see Cleaning the machine).
• Failure to comply with the instructions described in sections Position-
ing and Saving energy can cause a higher power.
The symbol on the product or on its packaging indicates
that the this product may not be treated as household
waste. Instead it should be handed over to the appropri-
ate collection centers for recycling electronic and elec-
trical appliances.
The correct bussing of this product will help prevent po-
tential negative effects on the environment and human
health, which could otherwise be caused by inappropri-
ate waste handling of this product. For more detailed in-
formation regarding the process, and re the use of this
product, please contact your local ofce, your house-
hold waste disposal or shop where you purchased the
product.
6
Important warnings
The appliance is manufactured in compliance with all relevant security standards, but
nevertheless do not recommend that adequate control using face impaired physical,
motional, or mental abilities, or persons without the required knowledge or experience.
• In accordance with the concern about preserving the environment, taking care not
to damage the structure apparatus (or condenser tubes, for example, in transport the
old appliance), or parts of the cooling system inside the appliance.
• The appliance contains a refrigerant and oil, so remove the damaged machine
compliance with environmental requirements (see section Our concern for the envi-
ronment).
• If the mains supply cable el. Energy is damaged, to avoid danger must substitute
manufacturer, its service agent, or qualied personnel.
• The camera does not keep ammable, volatile or explosive substances, such as eg.
explosives or sprays containing volatile solvent (such as butane,
propane, pentane and the like). These sprays can be identied by the printed label
content or symbol for ammability.
• Bottles with high alcohol must be sealed and arranged in a vertical position.
• Warning: Open for ventilation apparatus, must constantly be kept clean and unob-
structed.
• Warning: To defrost not use mechanical devices or other methods
other than those recommended by the manufacturer.
• Warning: When installing, cleaning and removal of obsolete appliance, make sure
not to damage the insulation or parts of the cooling system. This will prevent
environmental contamination.
• Warning: The interior of the appliance do not use electrical appliances except those
that the manufacturer of the appliance for cooling and freezing.
The appliance is properly connected to the power grid (refer to section
Connection to the power network).
Always unplug from the mains prior to repairs, before cleaning and be-
fore replacing the light bulb.
When switching off the machine, grasp the plug, and do not pull on the
supply cable.
!
7
Installation and
connection
proper functioning of the apparatus is conditioned by
the performance (Class) of the appliance, which is
indicated on the label with data on the appliance.
Unique Wine Cooler 400 is in CC5 Tropic this. class
Do not place the device near a heating and not
ispostavljajte by direct sunlight rays. At short distances
from the source heat, use the isolating plate.
The appliance must be set right, and steady to
sufciently hard surface. All models are equipped
the legs for easier leveling regulation appliance.
Classes Ambient temperature
N (normal) from +16°C to +32°C
SB (subtropical) from + 16 ° C to + 38 ° C
CC5 Tropic from +16°C to +42°C
Selection space
8
Levelling appliances
• Larger Phillips screwdriver or by hand from the
outside Turn the legs and thereby raise or lower the
machine and straighten it.
• Accurately determine the position of the camera,
which should in vertically gently sloping to the back
or front feet should be more twisted by approximately
1 cm from the last two legs and to showcase stands
stable without swaying.
Setting up appliances
The front left leg
The front right leg
Rear Right holder
Last left holder
1. Lowering screwdriver turn right
2. Lifting screwdriver turn left
9
Connecting to
electricity grid
The appliance plug in the mains connecting the supply
cable. The wall socket must be Grounding (security
socket). prescribed rated voltage and frequency are
indicated on the label with basic data on the appliance.
Connecting to the power supply and grounding appli-
ances must be made according to current standards
and regulations. The device can withstand short du-
ration voltage deviations, but only the most from -6 To
+ 6%.
If the voltage is not within the specied label with basic
data on aparatu.-any defects caused by maladjusted
voltage (not built-in correctors voltage) a malfunction
outside the warranty period, and the same can be re-
moved at the expense of the customer.
10
Tabla de contenidos
