Uniden UH200 Series Manual de usuario
For more exciting new products please visit our website:
Australia: www.uniden.com.au
UH200 Series
UHF CB Transceiver
2
UNIDEN UH200 Series
Warnings and Information
NOTE
The citizen band radio service is licenced in Australia by ACMA
Radio-communications (Citizen Band Radio Stations) Class
Licence and in New Zealand by MBIE General User Licence
for Citizen Band Radio and operation is subject to conditions
contained in those licenses.
USER LICENSE INFORMATION
User License Information
LITHIUM ION BATTERY PACK WARNING
• This equipment contains a Lithium Ion Battery Pack.
• The Lithium Ion Battery Pack contained in this equipment may
explode if disposed of in a fire.
• Do not short-circuit the Battery Pack.
• Do not charge the Lithium Ion Battery Pack used in this equipment in
any charger other than the one designed to charge this Battery Pack.
Using another charger may damage the Battery Pack or cause the
Battery Pack to explode.
• Lithium Ion batteries must be disposed off properly.
Do not expose this product to Rain or Moisture.
Uniden does not represent this product to be waterproof.
WATER WARNING
3UHF CB Transceiver
Included in your Package
CH
VOL
PTT
1
2
3
4
5
6
7
8
9
10
12
11
1 Antenna
2 [ + ] Key
3 [ -- ] Key
4 [ M ] / ( I ) Menu/Power
5 Microphone
6 Speaker
7 Lanyard Hole
8 LCD Display
9 Accessory Jack
10 PTT Key
11 PTT/LED Indicator
12 Micro USB Charge
NOTE
If any of these items are missing from the box, contact your
place of purchase, immediately.
2 x Earpiece Mic
2 x Lanyards
1 x Soft Carry Case
1 x Owner's Manual
2 x UH200 Radio
2 x Li-ion Battery*
2 x Belt Clips*
1 x Twin USB AC adaptor
2 x Micro USB cable
* Items may come pre-fitted
Controls & Indicators
4
UNIDEN UH200 Series
Controls & Indicators
Key Press Press & Hold
[ + ] Volume Up Transmit Call Tone
[ - ] Volume Down Key Lock On/Off
[ M ] Menu Mode Power On/Off
Key Functions
Key Press Press & Hold
[ + ] Next setting Scroll up through settings
[ - ] Previous setting Scroll down through settings
[ M ] Menu Mode Save setting & Exit MENU Mode
MENU Mode
Press [ M ] and [ + ] Change Transmit Power between High and Low
Press [ M ] and [ - ] Key Beep On/Off
Combination Keys (Standby Mode)
Standby Mode
2
4
3
5
11. Main Display/channel Indicator
2. Channel
3. Volume
4.
5.
CTCSS is active on this channel
when this segment appears
DCS is active on this channel
when this segment appears
LCD Display
5UHF CB Transceiver
Getting Started
Attach / Remove the Belt Clip
To attach the belt clip:
1. Align the belt clip over the 2 screw holes on the back of the battery pack.
2. Use a suitable Philips screwdriver to fasten the 2 belt clip screws to the
battery pack.
To remove the belt clip:
1. Use a suitable Phillips screwdriver to loosen the 2 belt clip screws to
release the belt clip from the battery pack.
NOTE
Always ensure the radio is powered off before removing the
battery.
Install / Remove the Battery Pack
To remove the battery pack
1. Make sure the radio is powered off.
2. Push down on the release lever at the top of the battery and lever the
battery away from the radio.
To install the battery pack
1. Lever the bottom of the battery into the bottom of the battery compartment
and then fit the battery in until the release latch at the top locks into place.
6
UNIDEN UH200 Series
Getting Started
Low Battery Alert
During normal use, if the battery level becomes low, the unit will go into a
Battery Low Mode and a battery low tone will intermittently sound, with the
PTT LED indicator intermittently flashing RED.
The Transmit Mode is also disabled. Recharge the batteries.
Power Save
Your UH200 Series has a unique circuit designed to extend the life of the
batteries. If there is no transmission nor an incoming call within a certain time,
your Radio switches to the Power Save mode. The Radio is still able to
receive transmissions in this mode.
Back Light
The UH200 has an automatic display back light which remains on for 5
seconds after the last activity.
Charging the Rechargeable Battery
Plug one end of the micro USB cable into the UH200 radio and the other end
to the AC adaptor. Plug the AC adaptor into a 240VAC wall outlet.
NOTE
Always power OFF the radio before charging the battery pack
•The battery level percentage will display during charging.
•The PTT LED indicator turns BLUE when charge is full.
•Before operating the radio, charge the rechargeable battery pack for
3 hours without interruption.
•Do not transmit when the radio is charging.
7UHF CB Transceiver
Operation
Volume
Press [+]to increase the volume. Maximum volume level is 05.
Press [-]to decrease the volume. Minimum volume level is 00.
NOTE
For maximum range and extended the life of the batteries,
avoid touching the antenna with your hand when transmitting.
• When you have finished release PTT.Listen for a response.
To Transmit and Receive
The UH200 Series uses the UHF-CB Channels. Refer to page 13 for UHF
channel usage.
• The transmit power of the UH200 Series is 2W in high power mode and
500mW in low power mode, see p4, Combination Keys (Standby Mode).
• Before you transmit, listen for activity on the selected channel.
The PTT LED lights up BLUE when there is a signal.
• When the channel is clear, press and hold PTT to transmit.
The PTT LED lights up RED during Transmit.
Hold the radio with microphone approximately 5 cm in front of your mouth
with the antenna at approximately 45°angle away from your head. Speak in
a clear, normal conversational voice.
Press and hold [M]/(l)to turn the radio on or off.
When the radio turns on:
•The Battery level percentage will display momentarily.
•The power on tone sounds and the PTT LED will flash BLUE/PURPLE.
•The PTT LED will flash BLUE every 10 seconds to incicate power is on.
NOTE
Power Off is not available when in MENU Mode.
Exit from MENU Mode first and then attempt Power off.
Power ON
8
UNIDEN UH200 Series
Operation | MENU Mode
The squelch is used to eliminate any annoying background noise when
there are no signals present.
Sq 00 - max sensitivity (min squelch), Sq 09 - min sensitivity (max squelch)
To adjust the Squelch
• Press [M]2 times until S9 flashes on the display.
• Then press [+]or [-]to change the setting between 00-09, and then
press & hold [M]to save the desired setting.
Squelch
NOTE
UHF CB Repeaters are used to retransmit or relay your signal.
Repeaters will extend the range of your radio and overcome the
shielding effect caused by solid obstructions.
Repeater channels can be selected directly as CHr1-r8
(CH01-08 repeaters) and CHn1-n8 (CH41-48 repeaters).
Contact your retailer for a list of repeaters available in your area.
The UH200 has 80 UHF CB Channels with selectable repeater channels for
CH01-08 and CH41-48.
To select a Channel
• Press [ M ]. CH flashes on the display.
• Then press [+]or [-]to change the channel between 01-80, and then
press & hold [M]to save the desired setting.
Channels
1. Channel Select
2. Squelch Select
3. CTCSS/DCS Select
4. Scan Start
5. Scan Memory On/Off
6. VOX Off/Select
7. BCL On/Off
8. Call Tone Off/Select
9. Roger Beep On/Off
10. Compander On/Off
11. Vibrate On/Off
12. Scramble On/Off
MENU Mode
9UHF CB Transceiver
Operation | MENU Mode
NOTE
Channels 05 and 35 are used for emergency channels. CTCSS
and DCS will not operate on these two channels.
• Press [M]3 times until PS flashes on the display.
• Then press [+]or [-]to change the setting between off, '01-'50, i01-
i99, and id0-id4 and then press & hold [M]to save the desired setting.
NOTE
Select off (oF) to turn CTCSS/DCS off for the selected channel.
CTCSS
(Continuous Tone Coded Squelch System)
CTCSS is a feature that allows a group to talk to each other without hearing
other users on the same channel.
DCS
(Digital Coded Squelch)
DCS is a digital extension of CTCSS. It provides 104 extra, digitally coded
squelch codes that follow after the 50 CTCSS codes. CTCSS 1-50 (displays
as '01, '02, '03... '50), followed by DCS 1-104 (displays as i01-i99 and id0-id4).
Follow the steps for changing CTCSS code but select a DCS code as desired.
To use CTCSS or DCS
First select a desired channel.
10
UNIDEN UH200 Series
Operation | MENU Mode
• Press [M]6 times until Uflashes on the display.
• Then press [+]or [-]to change the setting between off, 1-10, and then
press & hold [M]to save the desired setting.
VOX
VOX is Voice activated transmission, no pressing of the PTT key. For
optimum performance, use VOX when the accessory earpiece is connected.
When VOX is turned on (levels 1-10), the earpiece microphone is most
sensitive at level 1, and least sensitive at level 10.
To use VOX
To use SCAN Memory
• Press [M]5 times until Sn flashes on the display.
• Then press [+]or [-]to change the setting between on or off, and then
press & hold [M]to save the desired setting.
The currently selected Channel can be removed or added to the SCAN list
with this selection.
SCAN Memory
NOTE
The factory has preprogrammed all the UHF-CB channels into
the Scan channel memory. Use SCAN Memory to remove or
add the current channel.
The UH200 has a Scan function which searches all the channels and
frequencies in its memory continuously. The currently selected channel can
be removed or added to the scan memory in SCAN Memory.
To Start Scanning
• Press [M]4 times until SC flashes on the display.
• Then press [+]or [-]to immediately start scanning.
If an active channel is found, scanning will stop on that channel.
To skip an active channel, press [+]or [ - ].
To Cancel Scanning, press [ M ].
SCAN
Tabla de contenidos
Otros manuales de Transceptor de Uniden
Uniden
Uniden UH405SX-2NB Manual de usuario
Uniden
Uniden DSC Series Manual de usuario
Uniden
Uniden MHS050 Manual de usuario
Uniden
Uniden UH076 Manual de usuario
Uniden
Uniden SPU554KTS Manual de usuario
Uniden
Uniden UH078SX-NB Manual de usuario
Uniden
Uniden UH037SX-2 Manual de usuario
Uniden
Uniden X66 Manual de usuario
Uniden
Uniden UH750 Manual de usuario
Uniden
Uniden UH8060S Manual de usuario
Uniden
Uniden GRANT XL Manual de usuario
Uniden
Uniden UH037SX-2NB Manual de usuario
Uniden
Uniden UH5060 Manual de usuario
Uniden
Uniden UH078SX-NB Manual de usuario
Uniden
Uniden UH35 Series Manual de usuario
Uniden
Uniden JACKSON Manual de usuario
Uniden
Uniden SEA-WASP MC-4300 Manual de usuario
Uniden
Uniden UH5045 Manual de usuario
Uniden
Uniden POLARIS Manual de usuario
Uniden
Uniden UH001 Manual de usuario
