Uni-Mig MINI-MIG 120 Manual de usuario

MINI-MIG 120

Manual

UNI FLAME AUTOLIFT

10AMPPLUG

FANCOOLED 240Volt

Standard

MIG / MAG

Machine Model

Description Part Number

MINIMIG120 KMM120

CONTENTS PAGE No:

Safety 3

Main Parameter. 4

Machine Features 4

Installation & Operation 4

Caution 11

Maintenance 12

Troubleshooting 12

Machine Model

UNI FLAME AUTOLIFT

UNIMIG pursue a policy of continuous research and development, and therefore

reserve the right to change the specifications, or design, without prior notice. *2 year warranty power source.

YEARS Warranty*

3

•Do not switch the function modes while the machine is operating.

Switching of the function modes during welding can damage the machine.

Damage caused in this manner will not be covered under warranty.

•Disconnect the electrode-holder cable from the machine before switching on the

machine, to avoid arcing should the electrode be in contact with the work piece.

•A safety switch is necessary to prevent the equipment from electric leakage.

•Welding tools and accessories should be of high quality and in good working order.

•Operators should be trained and or qualiﬁed. Electric shock: It can kill.

•Connect the primary input cable according to Australian standard regulation.

•Avoid all contact with live electrical parts of the welding circuit, electrodes and wires with

bare hands. The operator must wear dry welding gloves while he/she performs the

welding task.

•The operator should keep the work piece insulated from

himself/herself. Smoke and gas generated whilst welding

or cutting can be harmful to people’s health.

•Avoid breathing the smoke and gas generated whilst

welding or cutting. Keep the working area well ventilated.

•Arc rays are harmful to people’s eyes and skin.Always

wear a welding helmet and suitable protective

clothing including welding gloves whilst the welding

operation is performed.

•Measures should be taken to protect people in or near

the surrounding working area, from all hazards

associated with welding.

Fire hazard

•The welding sparks may cause ﬁre, therfore remove

ﬂammable material away from the working area.

•Have a ﬁre extinguisher nearby, and have a trained

person ready to use it.

Noise: possibly harmful to people’s hearing.

•Noise is generated while welding/cutting, wear approved

hearing protection when noise levels are high.

Machine fault:

•Consult this instruction manual.

•Contact your local dealer or supplier for further advice.

SAFETY

Welding and cutting equipment can be dangerous to both the operator and people in or near the

surrounding working area, if the equipment is not correctly operated. Equipment must only be

used under the strict and comprehensive observance of all relevant safety regulations. Please

read and understand this instruction manual carefully before the installation and use/operation

of this equipment.











*** CAUTION ***

Do not heat, cut or weld tanks, drums or containers

until the proper steps have been taken to insure that

such procedures will not cause ﬂammable or toxic

vapours from substance inside. These can cause

an explosion even though the vessel has been

“cleaned”.Vent hollow castings or containers before

heating, cutting or welding. They may explode.

UNI FLAME AUTOLIFT

UNI FLAME AUTOLIFT

UNI FLAME AUTOLIFT

UNI FLAME AUTOLIFT

UNI FLAME AUTOLIFT

UNI FLAME AUTOLIFT

UNI FLAME AUTOLIFT

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Sistema de soldadura de Uni-Mig

Uni-Mig

Uni-Mig 270SWF Manual de usuario

Uni-Mig

Uni-Mig RAZOR CUT 45 PFC Manual de usuario

Uni-Mig

Uni-Mig KUMJR200AC/DC Manual de usuario

Uni-Mig

Uni-Mig VIPER 150 MIG Manual de usuario

Uni-Mig

Uni-Mig 390 Manual de usuario

Uni-Mig

Uni-Mig Razor 250 Manual de usuario

Uni-Mig

Uni-Mig RAZOR COMPACT 250 Manual de usuario

Uni-Mig

Uni-Mig RAZOR TIG 200 AC/DC Manual de usuario

Uni-Mig

Uni-Mig 345SWF Manual de usuario

Uni-Mig

Uni-Mig 345SWF Manual de usuario

Uni-Mig

Uni-Mig RazorCut KUPJRRW40 Manual de usuario

Uni-Mig

Uni-Mig RAZOR CUT 120 Manual de usuario

Uni-Mig

Uni-Mig 500SWF Manual de usuario

Uni-Mig

Uni-Mig RAZORCut 45 Manual de usuario

Uni-Mig

Uni-Mig VIPER Manual de usuario

Uni-Mig

Uni-Mig KUMJRRW200 Manual de usuario

Uni-Mig

Uni-Mig CUT40 Manual de usuario

Uni-Mig

Uni-Mig KUMJR350K Manual de usuario

Uni-Mig

Uni-Mig UNI-PLAS 50/80 Manual de usuario

Uni-Mig

Uni-Mig RAZOR ARC 160 PFC Manual de usuario

Uni-Mig

Uni-Mig VIPER ARC 140 Manual de usuario

Uni-Mig

Uni-Mig VIPER MULTI165 Manual de usuario

Uni-Mig

Uni-Mig KUMJRRW180CA Manual de usuario

Uni-Mig

Uni-Mig RAZOR ARC 140 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario