Uni-Line Smart Sense SMART 3000 Manual de usuario

SMART 3000 Touchscreen Thermostat

Quick Start Guide

www.robertshaw.com

by Uni-Line®

IMPORTANT SAFETY INFORMATION

WARNING: ELECTRICAL SHOCK HAZARD – Turn off power at the main

power source by unscrewing fuse or switching circuit breaker

to the OFF position before installing, removing, or cleaning

this thermostat.

WARNING: FIRE AND ELECTRIC SHOCK HAZARD – This device should be

installed by a qualified service technician with due regard

for safety as improper installation could result in a fire and

electric shock hazard.

WARNING: FIRE AND ELECTRICAL SHOCK HAZARD – This is a 24V AC

low-voltage thermostat. Do not install on voltages higher

than 30V AC.

• Do not switch system to cool if the temperature is below 50°F (10°C). This

can damage your cooling system and may cause personal injury.

• Do not short (jumper) across terminals on the gas valve or at the system control

to test installation. This will damage the thermostat and void the warranty.

• Do not connect ground to any terminal in this unit.

• All wiring must conform to local and national building and electrical codes

and ordinances.

• Use this thermostat only as described in the manual.

Thank you for purchasing a SmartSense

thermostat by Uni-Line

. The SMART 3000

isamul-funconthermostat.Severalconguraonsmaybeprogrammed

throughthebuoninterfaceorremotely,usingModbuscommunicaons.

Thisisaquickstartguideonhowtoperformthebasicinstallaon,programming

andtesngoftheSMART3000soitfunconsasasingle-stage,manual

thermostat.

Onlythestepsneededtoprovideafunconingthermostatwithminimalfeatures

andprogrammingwillbediscussed.Whennished,thethermostatwillbe

operaonalforthefollowing:

• Manual thermostat

• 1 Speed Fan

• 1 Heat/1 Cool

• 2 pipe mode

• Thermostat controlled fan

• Short cycle timer at five minutes

• Single setpoint

Mounting the SMART 3000 Thermostat

IMPORTANT: The SMART 3000 can only be as accurate as the onboard

temperaturesensor,oritsoponalremotetemperaturesensor(s)

permit. The SMART 3000 should be mounted in a location that is

typical of the ambient room temperature. Do not install near the

floor,inadraft,behindadoor,oronanon-insulated,exteriorwall.

InstalltheSMART3000awayfromexposuretosunlightandfourto

five feet (1.2 to 1.5 m) above the floor.

Figure 1

• Locate the slot on the housing at the bottom. Take note of the hinge points

and the connection between the two halves.

• Insert a screwdriver or coin into the slot and twist. This will separate the two

halves.

• Continue to swing the top half upward. This will release the tabs holding the

top half in place.

• Pull the control wires through the large opening in the base plate.

• Position the base plate on the wall and attach it with appropriate fasteners

(two screws with drywall anchors are supplied). The base plate should be

visibly level.

• Block any holes where wires are pulled through a wall opening. This will

prevent drafts from entering the back of the thermostat.

Do not use

these holes for

mounting.

Figure 2

IfthisinstallaonwillbeusingModBuscontrolsorremotesensors,becertainto

includetheproperwirestomakethoseconnecons.

Switch Set-Up

LocatetherowofeightfunconDIPswitches.

Figure 3

Switch 1 2 3 4 5 6 7 8

Position OFF OFF ON ON ON OFF OFF OFF

NOTE: ThiswillconfiguretheSMART3000asamanualheat/cool,singlestage,

single setpoint thermostat.

Wiring

Terminal Funcon

C 24V Common or Neutral

R 24V AC - This voltage is switched back through the relays

Hi Indoor Fan High Speed (NOT Used in Single fan speed mode -

Sw 1 = OFF)

Med Indoor Fan Medium Speed (NOT Used in Single fan speed mode -

Sw 1 = OFF)

Low Indoor Fan Low Speed (Used in single and three fan speed mode)

Y Compressor or Cool - (Based on Sw 2 setting)

W - O/B Reversing Valve or Heat - (Based on Sw 2 setting)

A1 – Cool 0 to 10V Output for Cooling (Typically used to control modulating valves)

A2 – Heat 0 to 10V Output for Heating (Typically used to control modulating valves)

A3 – Fan 0 to 10V Modulating Output for Indoor DC Fan

Com – 0V 0Vterminal-Usedfor0to10V,sensorordigitalinputsgroundreference

A ModBus Data A

B ModBus Data B

SI Remote temperature sensor input (Remote/average/ModBus data use)

DI Digital (Switched input) for forced unoccupied or initiate doorbell

function

Terminal Funcon

WC Window Contact - Forces SMART 3000 OFF if window open > five min

(Adjustable)

DS Door Switch – Monitors room door status for occupancy detection

PIR PIR (Movement sensor) input for occupancy detection

TheSMART3000ispoweredby24VACandrequiresthe24VACacveand

neutraltobeconnectedtotheR(acve)andC(Neutral)terminalstofuncon.

The 24V AC applied to the SMART 3000 R terminal is switched back through the

2A relays to the equipment.

Figure 4

Fan

Cool

Heat

24 V AC

24 C Neutral

Figure 5

Close the Cover

• Hold the cover up and connect the top hinge points between the two halves.

• Position the top cover with the pins in the base plate openings.

• Swing the top half downward until it snaps in place. The electrical pins at the

bottom will slide into the terminal strips.

Apply Power

• Apply the 24V AC power to the SMART 3000. The screen should display the

current temperature.

Test

Eachpressofabuonshouldproduceanaudiblebeep.

Figure 6

• Press the Fan button to test the fan operation.

• Use the Up and Down arrow buttons to adjust the setpoint.

• Adjust the setpoint five degrees above the room temperature. After a few

moments the heating system should come ON.

• Adjust the setpoint five degrees below the room temperature. After a few

Tabla de contenidos

Otros manuales de Termostato de Uni-Line

Uni-Line

Uni-Line PerfectSense PS3210 Series Manual de usuario

Uni-Line

Uni-Line PERFECTSENSE PS2210 Series Manual de usuario

Uni-Line

Uni-Line Smart Sense SMART 1000 Manual de usuario

Uni-Line

Uni-Line Perfect Sense PS4000 Instrucciones de instalación

Uni-Line

Uni-Line SmartSense SMART 3000 Manual de usuario

Uni-Line

Uni-Line PERFECTSENSE PS3110 Series Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario