Ultra Start 430 Series Manual de usuario

Technical Support 866-698-5872 ext 0

Support@ultrastarters.com

FCC/ID Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

CAUTION: Changes or modifications not expressly approved by the part responsible for compliance

void the user’s authority to operate this devise.

430 and 440 Series Vehicle Security Systems

INSTALL GUIDE

WWW.ULTRASTARTERS.COM

Table Of Contents Page 2

Wiring Diagram Page 3

Installation Tips Page 4

Pre-Installation Suggestions

Installation Suggestions

Mounting The Module

Installing The LED

Installing The Program Button

Under Hood Connections

Mounting The Siren

Wire Connectors Page 5

14 Pin Main Harness Connector

4 Pin Red Connector- Keyless Entry

2 Pin Connector Red- Plug-in LED

2 Pin Blue Connector- Plug-in Program Button

3 Pin White Connector- Aux. outputs

4 Pin White Connector- Addition sensor input

Installation Page 6-7

Basic Installation - Quick start

Shock Sensor Adjusting

Test The System

Programming Page 7-9

Program Overview

Quick View Programming

System Reset

Operations Page 10

Transmitter Programming

Battery Replacement

Other Features Page 11

System Service Mode

Service Mode- By remote

Diagnostics Page 12

COMPONENTS

TABLE OF CONTENTS

- Three Button Remote transmitter’s (430 Series)

- Four Button Remote transmitter’s (440 Series)

- Plug-in Valet Switch (Program Switch)

- 10 Pin Main Harness

- 2 pin Keyless Entry harness

-Control Module

- Plug-in Led

- Multi-Tone Siren

- Installation Guide

- Owners Manual

Blue

Connect to hood and / or trunk pin Hood Input

Green

Connect to door pin. (-) when opened Door Input

Purple

Connect to door pin. (+) when opened Door Input

Black

Connect to chassis ground Ground Input

Brown

Connect to Siren wire. 2amp Maximum Siren Output

Red

Connect to constant power. 20amp input 12 Volt Input

Yellow

Connect to vehicles ignition wire Ignition Input

Gray

*500ma negative output

Trunk Release

Orange

*500ma negative output (-) When Armed

WIRING DIAGRAM

Recommended Installation Procedures

White (+) Park lights Park light output.

Orange (-) When Armed Negative output when system is armed.

Grey (-) Trunk Release Negative output for trunk release. 500ma max.

Yellow Ignition Input Input from vehicles ignition wire.

RedMain Power Input Constant 12 Volt input.

Brown (+) Siren Output Positive output for siren.

Black Ground Input System ground input.

Purple (+) Door Input Positive door pin switch input.

Green (-) Door Input Negative door pin switch input.

Blue (-) Hood Input Negative input from hood pin switch.

10 Pin Connector

Green Door Lock Door Lock Output - *Programmable

12 Volt Output Output for voltage inverter. Low Current Only

Blue Door Unlock Door Unlock Output - *Programmable

3 Pin Connector Red

Under Hood Connections- Route the hood pin (optional) and Siren wire through the

firewall, into the engine compartment. Always try to pull the wires through a factory rubber

grommet. If drilling through the firewall, BE CAREFUL. Check for obstructions on both sides

of the firewall. After drilling use a snap in grommet to protect the wires from sharp edges.

Mounting the module- Never mount the module in the engine compartment. Select a

location under the dash to install the main module. Be certain that the module is securely

attached and does not obstruct any serviceable areas. Mount the module so that it cannot

be seen if looking under the dash as it could be easily unplugged by a thief. The module

must be free from all moving parts.

Mounting the Siren- Choose a location in the engine compartment that is away from

high heat sources and direct exposer to water. The siren should be mounted as well as

grounded to solid metal. Run the wiring for the siren so that it can not be seen or reached

from below the vehicle.

Installing the LED- Choose a location that will be highly visible when the LED is installed.

Most vehicles are equipped with knock out panels in the dashboard, these panels are easily

removable and can be easily replaced if necessary. Once the location is picked, use drill bit

and drill a hole through the panel. Test fit the LED into the hole. Plug the Led into the Red

connector on the main module.

Installing the Program Button- Choose a location to mount the Program Button. This

location should be hidden and not visible from outside the vehicle. Once the location of the

switch is picked, use a 1/4” drill bit and drill a hole. Remove the nut and push the Program

Button through the hole. Replace the nut and tighten until the switch is secure. Plug the

Program Button into the Blue connector of the main module.

10 Pin Power Connector

Step 2- Plug-In The Module

Step 3- Test And Adjust The Shock Sensor

Your Basic Install Is Complete!

Step 4- Test The System

Step 1 - Connect All Of the Following Wires

When all the connections are done, the control module can be plugged in. Before

connecting the control module, make sure the ignition is in the OFF position. Plug in the

main harness then any other connectors that were used.

Black Ground Input System ground input.

Yellow Ignition Input Input from vehicles ignition wire.

Red Power Input Constant 12 Volt input.

Brown (+) Siren Output Positive output for siren.

White (+) Park lights Positive park light output.

Green* (-) Door Input Negative door pin switch input.

Purple* (+) Door Input Positive door pin switch input.

*Test for door pin type (+ or -) then connect the appropriate wire (Green or Purple)

To test the Shock Sensor.

1. Press the Lock button once to arm the system.

2. Wait five seconds then impact the vehicle. Lighter impacts to the vehicle should trigger

the warn away (The siren will chirp three times). A harder impact to the vehicle will trigger

the full alarm.(The siren will activate for 60 seconds then turn off).

3. To deactivate the alarm when triggered, press the unlock button twice.

To Increase The Sensitivity.

Turn the adjustment screw Clockwise 1/4 turn then re-test the sensitivity. Repeat this

procedure until the sensitivity of the system is at the appropriate level.

** Do not set to sensitive.

To Decrease The Sensitivity.

Turn the adjustment screw Counter Clockwise 1/4 turn then re-test the sensitivity. Repeat

this procedure until the sensitivity of the system is at the appropriate level.

1. Open all the vehicles windows.

2. Press the Lock button to arm the system.

3. Wait five seconds (or until the dome light goes out) then reach in through a window and

open the door. The alarm will then activate (repeat on all the doors).

4. Test the Shock Sensor again and adjust if necessary.

5. Insure that all additional features are working as intended.

6. If necessary proceed to Program Mode to adjust the programmable outputs.

BASIC INSTALLATION

Program mode allows you to adjust the settings and options of your system. Your system

has been intelligently designed by installers with years of experience. The system’s default

settings do not require any program changes in most cases. However, this system does

incorporate a advanced programming system with settings that can be easily adjusted

PROGRAM OVERVIEW

Entering Program Mode

Changing A Programmable Setting

Quick View Programming

To Enter Program Mode

1) Make sure ignition is in the off position.

2) Within three seconds turn the key ON the OFF.

3) Press and release the Program Button two times.

4) The siren will chirp and the lights will flash once to confirm entering Program Mode.

Note:If unit does not enter Program Mode, turn ignition off and repeat steps 1-3.

** The ignition wire(Yellow) MUST be connected. If it is not connected it will not be possible

to enter the Program Modes.

System Reset

This feature will reset the module to it’s factory programmed default setting. This feature

will not delete transmitter codes from memory.

To Reset The System To Factory Defaults.

1) Turn the ignition key On then Off.

2) Press the Program Button two times. The system will respond with two siren chirps.

3) Press the transmitter buttons in the following order: #3-#3-#3. The system will respond

with three siren chirps to confirm the system has been re-set to factory defaults.

Programmable Feature Press Buttons One Chirp Two Chirps

Shock Sensor Status #3-#3-#1 Disabled Enabled

Arm / Disarm Chirps #2-#1-#1 Chirps Off Chirps On

Ignition Auto Locks #1-#3-#2 Off On

Door Lock Pulse Length #1-#3-#1 3 Second .75 Second

Double Pulse Unlock #2-#2-#1 Two Pulses Single Pulses

Door Input / Voltage Sense #1-#1-#3 Voltage Door Pin

Passive / Active Locks #3-#2-#2 Active Passive

Passive / Active Arming #1-#2-#3 Active Passive

System Reset #3-#3-#3 Confirmed by Three Siren Chirps

1) Enter Program Mode As explained above.

2) When in program Mode, change the desired Program Setting by pressing the

transmitter buttons in the following sequences.

***The Systems Default Setting Are Shown In Bold Lettering.

Entering program mode is done by the following steps:

1) Make sure ignition is in the off position.

2) Turn the ignition key ON - OFF, leaving key in the OFF position.

3) Press and release the Valet button two times.

4) The siren will chirp one time to confirm entering program mode.

( If this does not happen, turn ignition off, wait five seconds and repeat steps 1-4).

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #2 then #3

3- The siren will respond with the following:

1 Chirp Active Arming

2 Chirps Passive Arming

Repeat sequence to change selection

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #3 then #2.

3- The siren will respond with the following:

1 Chirp Auto Lock Disabled

2 Chirps Auto Lock Enabled

Repeat sequence to change selection

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#3 - #3 then #2

3- The siren will respond with the following:

1 Chirp Active Locks

2 Chirps Passive Locks

Repeat sequence to change selection

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #3 then #1

3- The siren will respond with the following:

1 Chirp 3 Second Door Locks

2 Chirps 0.75sec Pulses

Repeat sequence to change selection

Passive / Active Arming

Enter Program Mode

Passive / Active Arming

Door Lock Timing

Ignition Auto Locks

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #1 then #3

3- The siren will respond with the following:

1 Chirp Voltage Sensing- No Door Pin Connection Needed

2 Chirps Door Pin- Door Pin Connection Required

Repeat sequence to change selection

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#2 - #2 then #1

3- The siren will respond with the following:

1 Chirp Chirps Disabled

2 Chirps Chirps Enabled

Repeat sequence to change selection

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#3 - #3 then #1

3- The siren will respond with the following:

1 Chirp Shock Sensor OFF

2Chirps ShockSensorON

Repeat sequence to change selection

Voltage / Door Pin Sensing

Double Pulse Unlock

Chirp Delete

Shock Sensor Disable

To change settings:

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#2 - #2 then #1.

3- The siren will respond with the following:

1 Chirp Double Pulse Unlock

2 Chirps Single Pulse Unlock

Repeat sequence to change selection

- Press and release to arm the alarm and lock the doors.

- Press and hold to activate Panic mode.

- Press and release to deactivate triggered alarm.

-Press and release to disarm and unlock the doors.

- Press and hold to activate the Trunk Release.

- Press and release to deactivate triggered alarm.

- Press and hold to activate the Car Finder Mode.

Button #1

Button #2

Button #3

Transmitter Programming

Deleting Transmitters

Follow the steps below to program the transmitters to the system s memory

Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.

Step 2 - Press and release the Program Button twice then press and hold.

Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.

Note: If the siren does not respond, repeat Steps1&2

Step 4 - Continue to hold the Program Button and press lock button on each of the

transmitter’s to be programmed(Maximum of 3 Different transmitter codes).

Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.

Exit - After five seconds the system will exit transmitter program mode automatically.

NOTE: You must program ALL of the transmitters to be used at one time. For the owner’s

security any transmitters not programmed at this time will be erased from memory.

*** This system will store a maximum of three transmitter codes in memory.

Follow the steps below to permanently delete a transmitter code from the system s memory.

Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.

Step 2 - Press and release the Program Button twice then press and hold.

Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.

Note: If the siren does not respond, repeat Steps1&2

Step 4 - Continue to hold the Program Button and press lock button on only the transmitters

that are intended for use on the system.(*Maximum of 3 Different transmitter codes).

Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.

Exit - After five seconds the system will exit transmitter program mode automatically.

All previous transmitter code are now deleted from the systems memory.

#1 #2

#3 #1 #2

Basic Transmitter Functions

1.Press and hold the UNLOCK button for three seconds.

2.The doors will unlock, continue holding the unlock button three seconds. the

Trunk release will then activate. The trunk release will be confirmed by one

park light flash.

3.For safety reasons, the trunk release output will not activate when ignition

key is in the “On” po si tion .

1.Press & hold the LOCK button for three seconds.

2.The park lights will flash and the siren will activate.

PANIC MODE DISABLE

1. Press LOCK button to disable the panic mode and to lock the doors.

2. Press UNLOCK button to disable the panic mode and unlock the doors.

3. Panic Mode will stay activated until disabled by the remote transmitter.

1.Press & release the button three, then press & release the lock or unlock button.

2.If the doors are locked this will unlock the doors without siren chirps, the park

lights will flash two times to confirm the doors have unlocked.

3.If the doors are unlocked this will lock the doors without siren chirps, the park

lights will flash one time to confirm they have locked.

Trunk Release

Car Finder Mode

Panic Mode

1. Press and hold the button for two seconds.

2. The system will flash the park lights and chirp the siren five times.

**This feature can help find your vehicle in a crowded parking lot.

3sec.

1.Press & release the LOCK button on the remote transmitter.

2.The park lights will flash and the siren will chirp once.

3.The doors will lock.

4.The LED will start flashing within five seconds.

1.Press & release the UNLOCK button on the remote transmitter.

2.The park lights will flash and the siren will chirp twice.

3.The doors will unlock.

4.The LED will stop flashing.

Lock Doors & Arm The Alarm

Unlock Doors & Disarm The Alarm

Silent Arm And Disarm

Otros manuales para 430 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Alarma de coche de Ultra Start

Ultra Start

Ultra Start 650 Series Manual de usuario

Ultra Start

Ultra Start 440 Series Manual de usuario

Ultra Start

Ultra Start 42 SERIES Manual de usuario

Ultra Start

Ultra Start 1350 SERIES Manual de usuario

Ultra Start

Ultra Start 1271M Manual de usuario

Ultra Start

Ultra Start 42 SERIES Manual de usuario

Ultra Start

Ultra Start 600 SERIES Manual de usuario

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Ultra Start

Ultra Start 1270 series Manual de usuario

Ultra Start

Ultra Start 1280 series Manual de usuario

Ultra Start

Ultra Start 430 Series Manual de usuario

Ultra Start

Ultra Start 1270 series Manual de usuario

Ultra Start

Ultra Start G-Series Manual de usuario

Ultra Start

Ultra Start KEU-300 Series Manual de usuario

Ultra Start

Ultra Start MCS-100 Manual de usuario

Ultra Start

Ultra Start 80 Series Manual de usuario

Ultra Start

Ultra Start 640 Series Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 45 SERIES Manual de usuario

Ultra Start

Ultra Start 430 Series Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Ultra Start

Ultra Start 606 Series Manual de usuario

Ultra Start

Ultra Start 45xx Series Manual de usuario

Ultra Start

Ultra Start 42xx Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario

Clifford

Clifford Nova 3 Manual de usuario

Viper

Viper 560XV Manual de usuario

SECO-LARM

SECO-LARM 300C Manual de usuario