UFO MicroLED 4000P Hoja de especificaciones
PRODUCT USER GUIDE
M croLED 4000P L ght Source
PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING
OR PERFORMING MAINTENANCE ON THE LIGHT SOURCE UNIT
E357731
Rev: C2
INTRODUCTION
MICROLED 4000P USER GUIDE
2
Thank you for purchasing this UFO ight source/ uminaire.
To ensure that the ight source is set up optima y and gives a ong service ife, p ease read this
user guide before insta ing, operating or performing any maintenance on the unit.
P ease keep this User Guide for future reference. This User Guide is aid out in three sections
Insta ation -detai s on how to connect your uminaire
Operation - detai s how to programme and set up your uminaire
Maintenance - maintenance og, troub eshooting guide, technica specification
MODELS COVERED BY THIS USER GUIDE
UFO MIC4000P
IMPORTANT
This product must be insta ed in accordance with the app icab e insta ation code, by a person
fami iar with the construction and operation of the product, and the hazards invo ved.
These ight sources are not mains dimmab e.
The LED array in this ight source is not rep aceab e. When it reaches end of ife the who e unit
must be rep aced.
Type Y Attachment: If the externa f exib e cab e or cord of this uminaire or associated
PSU/driver is damaged, it sha be exc usive y rep aced by the manufacturer or his service agent
or a simi ar qua ified person to avoid a hazard.
Location: Do not ocate this ight source c oser than 200mm from any f ammab e surface.
C earance / Venti ation: It is imperative that a gap of 200mm is e around the unit. This is to
a ow air to circu ate and prevent overheating. The ocation must have free venti ation and must
not have an ambient temperature higher than that specified for the uminaire.
Mounting: This uminaire comes with an integra mounting p ate for securing the unit to a
vertica or horizonta surface. Refer to the instruction sheet supp ied with the p ate.
Warning: Never ook direct y at the uminaire through the fibre port of the ight source.
Warning: The uminaire shou d be positioned so that pro onged staring into the
uminaire at a distance c oser than 2.7 metres is not expected.
This uminaire is powered by a 12V Power Supp y Unit or 12V Constant Vo tage Driver. Remove
the PSU/driver from its box. Connect the jack p ug into the socket in the back, and the ight
source is now ready for connection.
POWER SUPPLY REQUIREMENTS
INSTALLATION
3
UFO LIGHTING
This uminaire supp ied with a separate mounting p ate. If using the mounting p ate refer to the
fitting instructions supp ied with it.
MOUNTING
There are 2 connections required - the fibre port and the mains supp y. The fibre port shou d be
connected first. Connect and secure the fibre optic connector into the front of the unit and
secure using the M5 ocking screw.
P ug the mains p ug into the e ectrica supp y socket. Switch on the power, the LED indicator
wi i uminate, and the ight source wi start up automatica y. If no ight is produced consu t
the troub eshooting section.
CONNECTION
REMOTE CONTROL
Descripon Details Comments
Power 2 x AAA baeries -
Range 30 metres Measured in free space, may be aenuated by
obstrucons or other RF devices
Frequency 2.4GHz Approved for use in UK, USA and Europe
With The ight source powered up as described
above, remove the rear cover on the remote contro
unit. Taking care not to touch any of the front
buttons, insert the batteries.
If you touch the remote contro buttons when
inserting the batteries it WILL effect the operation of
your remote contro . If you do accidenta y touch any
of the buttons, remove the batteries and start again.
Once the batteries are inserted do not use the
remote contro for 3 seconds.
BATTERIES
The remote contro unit is matched with the ight source at the factory.
If the remote contro is not matched or an additiona or rep acement remote contro is required
carry out the “Matching Remote to Light Source” instructions as detai ed ater in this guide.
If a remote contro is to be removed from contro of a ight source carry out the “Unmatching
Remote to Light Source” instructions as detai ed ater in this guide.
FURTHER INFORMATION
INSTALLATION
MICROLED 4000P USER GUIDE
4
REMOTE CONTROL OPERATION
No. Descripon Funcon
1 Buon Power on
2 Buon Power off
3 Colour Ring Touch control all colours (white not available)
4 Indicator Indicates controller acve when buons pressed
5 Buon Increase colour cycle speed
6 Buon Increase brightness
7 Buon Decrease brightness
8 Buon Decrease colour cycle speed
9 Buon [Mode +] Step up through colour cycle programmes
10 Buon [Mode -] Step down through colour cycle programmes
10
9
8
7
6
5
43
2
1
OPERATION
5
UFO LIGHTING
MATCHING REMOTE CONTROL UNIT TO LIGHT SOURCE
Remove the power p ug from the rear of the Light Source, then
rep ace and touch button 5 within 3 seconds, the Light Source
wi “b ink” twice s ow y indicating that the Remote Contro er
is matched to the Light Source.
UNMATCHING REMOTE CONTROL UNIT FROM LIGHT SOURCE
Remove the power p ug from the rear of the Light Source, then
rep ace and touch and ho d button 5 within 3 seconds and the
Light Source wi “b ink” 9 times indicating that the Remote
Contro er is unmatched from the Light Source.
Note:
More than one Light Source contro ed by one Remote Contro er wi
eventua y run out of sync with each other (co our cyc e mismatch)
REMOTE CONTROL MODES AND FUNCTIONS
Mode Buttons – Do not work in a oop, i.e. touching the mode+ button wi not eventua y bring
you back to mode 1. To revert to mode 1, either touch mode – button repeated y to step back
up through the mode numbers, or touch co our ring then mode+
Co our Ring –The co our ring can be used to se ect individua co ours by touching the ring
and s iding your finger around the ring,
Brightness – brightness can be increased or reduced in any mode using buttons 6 & 7
Cyc e Speed – speed of co our cyc ing in modes 3 to 14 can be adjusted using buttons 5 & 8
No. Mode Brightness Speed Comment
1 Stac white Adjustable Non adjustable
Touch colour ring then
mode + to enter this
mode at any me
2White and
colours mixed Adjustable Non adjustable
Colour ring control. Touch
colour ring to enter this
mode at any me
3 All colours fade Adjustable Adjustable No white
4 RGBW fade Adjustable Adjustable Red, green, blue, white
5 RGBW snap Adjustable Adjustable Red, green, blue, white
6 7 colours snap Adjustable Adjustable White and colours mixed
7 2 colours snap Adjustable Adjustable Red and white
8 2 colours snap Adjustable Adjustable Blue and white
9 2 colours snap Adjustable Adjustable Green and white
10 1 colour flash Adjustable Adjustable Red
11 1 colour flash Adjustable Adjustable Blue
12 1 colour flash Adjustable Adjustable Green
13 1 colour flash Adjustable Adjustable White
14 All colours
snap/fade Adjustable Adjustable Random
OPERATION
MICROLED 4000P USER GUIDE
6
REMOTE RANGE WALK TEST
Once the ight source is fu y insta ed carry out a comp ete range wa k test and record the range
in the tab e be ow.
This information is essentia for maintenance purposes to determine if the range/sensitivity is
reducing and a so to record dead areas within the remote contro units range due to RF
obstructions and/or RF interference.
Note: Where a ight source has more than one remote contro , reduction in operating range may
be experienced when both (or mu tip e) remote contro s are used simu taneous y.
Descripon Date Max Range
Controller 1
Controller 2
Controller 3
Dead Areas
OPERATION
7
UFO LIGHTING
To disab e the remote and revert to manua operation press one of the buttons on the rear of
the ight source. The ight source wi now respond to manua commands from the 2 contro
buttons as described be ow.
The ight source has 2 co our cyc es, each with 3 different speed settings, the co ours are
detai ed in the tab e be ow:
STANDALONE OPERATION USING INBUILT BUTTONS
Cycle Colour 1 Colour 2 Colour 3 Colour 4 Colour 5 Colour 6 Colour 7
1 White Red Orange Jade Green Cyan Blue
2 Red Orange Jade Green Cyan Blue White
The ight source is contro ed using the 2 push buttons on the rear of the unit.
The ower button stops and starts the co our cyc e.
The upper button is used to se ect the cyc e speed as fo ows:
Push the upper button repeated y unti the co our white is disp ayed. The ight source is now in
Cyc e 1 Speed A as detai ed in the tab e be ow. Each push reduces the speed. On the third push,
the co our red wi be disp ayed. The ight source is now in Cyc e 2 Speed A.
At any time the cyc e can be stopped on a co our and started again using the ower push
button.
To disab e manua operation and revert to remote contro operation, recyc e the power to
the ight source. The remote contro unit may need to be matched to the ight source as
detai ed on page 5.
Cycle Speed A - Fastest Speed B - Slower Speed C - Slowest
1 (White Start) Push once Push once Push once
2 (Red Start) Push once Push once Push once
OPERATION
MICROLED 4000P USER GUIDE
8
The MicroLED 4000 is programmed as a Master unit and is capab e of inter inking to and
contro ing MicroLED S ave Light Sources using a RJ45 cab e inking the two. In this Master
/S ave configuration the S ave Light Source wi fo ow the Master Light Source. The MicroLED
4000 Master Light Source, cannot be contro ed by a remote DMX contro er.
For the MicroLED 4000, remote DMX s ave contro can on y be achieved with MicroLED 2000
or MicroLED 4000 S ave Light Sources. See MicroLED 2000 or MicroLED 4000 S ave User Guides
for DMX wiring connections
DMX OPERATION
MAINTENANCE LOG
Date Maintenance Undertaken
Note: A record of a maintenance MUST be kept in the tab e above, indicating what maintenance
was undertaken and when. This MUST be dated for warranty purposes.
OPERATION & MAINTENANCE
9
UFO LIGHTING
Problem Possible Cause(s) Remedy
Unit is dead - LED
power
indicator is not
illuminated
Mains supply off Check supply and reinstate
Loose mains plugs Check plugs
PSU failed Replace PSU
Unit is dead - no
light output but LED
power indicator is
sll illuminated
LED array failure Replace LED unit
Switched off via remote control unit Recycle power to light source or switch on via
remote control
Poor light
output on bre
Unit needs cleaning
Carefully clean LED Lens
with dry cloth
Clean bre common end
Fibre port connector not
plugged in correctly
Ensure plugged in correctly
and secured with locking screw
Staonary on one
colour
Lower buon has been pressed Press lower buon once
LED driver has failed Replace LED unit
Colour cycle cannot
be stopped LED driver has failed Replace LED unit
Remote control
range reduced
or persistently
freezing
Baeries failing Replace baeries as per user guide and carry out
matching if necessary
Interference from external source Check for another device transming
RF interference
Remote control needs reset Remove and replace baeries as per user guide
Remote control failing Replace remote control unit
Light source receiver failing Replace light source
Light source
won’t
respond to
remote control
unit
Baeries failed Replace baeries as per user guide and carry out
matching if necessary
Light source in standalone mode Recycle power to light source
Remote control needs reseng Remove and replace baeries as per user guide
Remote control not matched to light source Carry out matching procedure as
detailed in user guide
Remote control failed Replace remote control unit
Light source receiver failed Replace light source
In master/slave
con guraon, slave
light source works
on standalone but
does not respond to
DMX from master
DMX cable disconnected or faulty Check DMX link cable connecons -
repair or replace
Master light source not
sending DMX signal
Check master light source - refer to the relevant
user guide troubleshoong secon
TROUBLESHOOTING
MICROLED 4000P USER GUIDE
10
Otros manuales para MicroLED 4000P
3
Tabla de contenidos
Otros manuales de Equipo de iluminación de UFO
UFO
UFO LPV2 Manual de usuario
UFO
UFO UFO MIC100P-3 Manual de usuario
UFO
UFO LUNA SLP-3000M Hoja de especificaciones
UFO
UFO MicroLED 100P Series Hoja de especificaciones
UFO
UFO MicroLED 1000P Hoja de especificaciones
UFO
UFO MIC100PT-3 Manual de usuario
UFO
UFO Sirius UFOSIRCW Manual de usuario
UFO
UFO MICROLED 2000 Manual de usuario
UFO
UFO MicroLED 100PT Hoja de especificaciones
UFO
UFO LUNA SLP-3000M Manual de usuario
UFO
UFO MBL1 Manual de usuario
UFO
UFO Unidrive CC9 Hoja de especificaciones
UFO
UFO NOVA DMX Hoja de especificaciones
UFO
UFO Comet Light Source Hoja de especificaciones
UFO
UFO GEM SLP-3000M Manual de usuario
UFO
UFO UFO MER3000M Manual de usuario
UFO
UFO Illuminator 150 CDMXG Manual de usuario
UFO
UFO Sirius Series Manual de usuario
UFO
UFO MicroLED 1000P Hoja de especificaciones
UFO
UFO IP-02 Hoja de especificaciones
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
