UFO Comet Light Source Hoja de especificaciones

PRODUCT USER GUIDE

Comet Light Source

PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING

OR PERFORMING MAINTENANCE ON THE LIGHT SOURCE UNIT

Rev: C1

Thank you for purchasing this UFO light source/luminaire.

This innovative light source is designed to provide a flexible and creative lighting solution. A row

of three powerful LED arrays provides impressive illumination for design elements such as

shooting star eects, custom lighting eects, water eects, chasing special eects and firework

eects, while rear panel push-button controls and an LCD display provides outstanding ease of

use.

The Comet Light Source utilises industry standard protocols for the ultimate in control. It is

dimmable and you can also specify your preferred wheel: a 10 segment colour change wheel,

twinkle wheel, or a number of special eects wheels and custom light output collars can be

produced by UFO for you to enhance your desired eect. This is the perfect light source for

imaginatively illuminating decorative fibre optic eect lighting.

To ensure that the light source is set up optimally and gives a long service life, please read this

user guide before installing, operating or performing any maintenance on the unit.

Please keep this User Guide for future reference. This User Guide is laid out in three sections

Installation -details on how to connect your luminaire

Operation - details how to programme and set up your luminaire

Maintenance - maintenance log, troubleshooting guide, technical specification

INTRODUCTION

COMET USER GUIDE

FEATURES

The Comet is a 60W white light LED Light Source with optional decorative or colour wheel

capability. The Comet LED Light Source driver PCB has all its control functionality fitted as

standard, available via rear panel connections, push buttons and LCD display.

• Manual dimming using rear panel push button controls with status display

• 0-10V (current source – receiving) dimming

• 0-10V (current source – receiving) decorative wheel speed

• 1-10V (current sink – sending) dimming

• DMX dimming – 3 channels (white light dimming, wheel speed, initialise/reset/LED/fan on and

o)

• Manual decorative wheel with bi-directional motor speed control, or Stop setting, where an

open wheel segment can provide maximum light output.

• Master slave functionality – one COMET acting as master controlling slave COMET luminaires

via DMX links

The Comet LED Light Source is powered from a multi-voltage, external 48V Class 2 power supply

unit, which will be configured for your country’s mains supply.

INSTALLATION

UFO LIGHTING

CONTROL &

PROGRAM

BUTTONS

DMX REMOTE

DISPLAY

CONNECTOR

48V DC

INPUT

CONNECTOR

0-10V / 1-10V

DIMMING

0-10V / 1-10V WHEEL

CONTROL

LCD DISPLAY

IMPORTANT

This product must be installed in accordance with the applicable installation code, by a person fa-

miliar with the construction and operation of the product, and the hazards involved.

These light sources are not mains dimmable.

The LED array in this light source is not replaceable. When it reaches end of life the whole unit

must be replaced.

Type Y Attachment: If the external flexible cable or cord of this luminaire or associated PSU/driver

is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar

qualified person to avoid a hazard.

Location: Do not locate this light source closer than 200mm from any flammable surface.

Clearance / Ventilation: It is imperative that a gap of 200mm is le around the unit. This is to

allow air to circulate and prevent overheating. The location must have free ventilation and must

not have an ambient temperature higher than that specified for the luminaire.

Mounting: This luminaire comes with an integral mounting plate for securing the unit to a

vertical or horizontal surface. Refer to the instruction sheet supplied with the plate.

Warning: Never look directly at the luminaire through the fibre port of the light source.

Warning: The luminaire should be positioned so that prolonged staring into the

luminaire at a distance closer than 2.7 metres is not expected.

Warning: NEVER hot plug the DC connector on the rear of the light source as this may cause arc-

ing of the DC current. Do not disconnect or connect power from the Comet light source by

removing or connecting the DC connector whilst the 48V PSU is live.

REAR PLATE DETAIL

INSTALLATION

COMET USER GUIDE

CONNECTION - FOR MANUAL OPERATION

There are two connections required – the fibre port and the power supply connections. The

fibre port should be connected first before the mains supply. Connect and secure the fibre optic

connector into the collar and the front of the unit and secure using the M5 knurled locking

screw. Ensure the fibre optic connector is fully inserted before tightening the locking screw.

Never run the luminaire with the fibre optic connector out of the collar.

Plug the power supply’s output into the Comets power supply input and then connect the

mains plug into a local mains supply. The Comet will initialise and display its current status.

Consult the Troubleshooting and Operation sections in this manual if the Comet does not

power up or operate as expected.

INSTALLATION

UFO LIGHTING

CONNECTION - FOR DMX REMOTE CONTROL &DMX MASTER / SLAVE OPERATION

There are three connections required – the fibre port, the DMX cables and the mains supply

cable. The fibre port should be connected first before the mains supply. Connect and secure the

fibre optic connector into the collar and the front of the unit and secure using the M5 knurled

locking screw. Ensure the fibre optic connector is fully inserted before tightening the locking

screw.

Never run the luminaire with the fibre optic connector out of the collar.

Wire up using the DMX cable from the DMX control system. Solder the cables to the 5 pin XLR

male and female plug and socket using pin outs as detailed below and plug in to the

connectors on the rear of the luminaire.

Pin Descripon

1 Ground/Shield

2 Data (cold)

3 Data + (hot)

4 Not used

5 Not used

Plug the power supply’s output into the Comets power supply input connector and then plug

the mains plug into a local mains supply. The Comet will initialise and display its current status.

Consult the Troubleshooting section in this manual if the Comet does not power up.

DMX NOTES

• Always use an approved DMX cable

• Always “daisy chain” a DMX cable or universe

• Never use a T joint on a DMX cable or universe, unless using and approved interface or splitter

• Never connect more than 30 devices to a single DMX universe unless using and approved

interface or splitter

• Always terminate the last device on a DMX universe by connecting a 120 ohm resistor across

DMX+ and DMX- across the last output connector

• This is a 3 channel DMX device always leave 3 channels free when addressing multiple Comet

luminaires i.e. address 001, 004, 007 etc.

• For master/slave operation all slaves must be connected together and to the master Comet

If there is no DMX data being received at a Comet light source the display will indicate “No

DMX” as shown in the example below for address 001

DMX 001 No DMX

INSTALLATION

COMET USER GUIDE

CONNECTION - FOR 0-10V(CURRENT SOURCE)OPERATION

This is a current source dimming and decorative wheel operation. For current source, the inputs

to the COMET require an external control voltage between 0V and 10V DC.

There are three/four connections required – the fibre port, the 0-10V cable(s) and the power

supply cable. The fibre port should be connected first before the mains supply. Connect and

secure the fibre optic connector into the collar and the front of the unit and secure using the

M5 knurled locking screw. Ensure the fibre optic connector is fully inserted before tightening

the locking screw.

Never run the luminaire with the fibre optic connector out of the collar.

Wire up and connect RJ45 plugs to the RJ45 connectors on the rear of the luminaire using pin

outs as detailed below. The le hand RJ45 connector controls dimming, the right-hand connec-

tor controls the decorative wheel motor. Ensure the 0-10V control system is powered up and

supplying a control voltage.

Pin Wire Colour

1 White / Orange

2 Orange

3 White / Green

4 Blue

5 White / Blue

6 Green

7White / Brown

8Brown

RJ45 Pin No Wire Colour Polarity Funcon

5 White / Blue +VE Posive Posive (10V) 010V Current Source Dimming

8Brown Ground (0V) Ground (0V) 010V Current Source Dimming

RJ45 Pin No Wire Colour Polarity Funcon

5 White / Blue +VE Posive Posive (10V) 010V Current Source Twinkle Motor3

8Brown Ground (0V) Ground (0V) 010V Current Source Twinkle Motor

RJ45 CONNECTOR (LEFT HAND) - DIMMING

RJ45 CONNECTOR (RIGHT HAND) - DECORATIVE WHEEL CONTROL

INSTALLATION

UFO LIGHTING

CONNECTION - FOR 0-10V(CURRENT SOURCE)OPERATION - CONTINUED

Plug the power supply’s output into the Comet’s power supply input and then connect the

mains plug into a local mains supply. The Comet will initialise and display its current status.

Consult the Troubleshooting and Operation sections in this manual if the Comet does not

power up or operate as expected.

0-10V NOTES

• This is a current source 0-10V control system. The input from the 0-10V controller (source)

supplies a varying control voltage between 0 and 10v to the luminaire to control the dimming

or decorative wheel motors, or both the dimming and the decorative motors

• Always use an approved CAT5 cable

• With no 0-10V input the luminaire will give no light output and the decorative wheel will be

stationary, but may move slightly. If this movement causes a problem, connect a 0-10V

controller set to 0V or set the Comet to manual control.

INSTALLATION

COMET USER GUIDE

CONNECTION - FOR 1-10V(CURRENT SINK)OPERATION

This is a current sink 1-10V dimming operation. For current sink dimming, the le-hand dim-

ming RJ45 socket of the Comet provides current flow to a remote electronic dimmer. The re-

mote electronic dimmer modifies the current returning to the Comet, thus providing remote

dimming control.

There are three connections required – the fibre port, the 1-10V cable and the mains supply

cable. The fibre port should be connected first before the mains supply. Connect and secure the

fibre optic connector into the collar and the front of the unit and secure using the M5 knurled

locking screw. Ensure the fibre optic connector is fully inserted before tightening the locking

screw.

Never run the luminaire with the fibre optic connector out of the collar.

Wire up and connect a RJ45 plug to the le hand RJ45 connector on the rear of the luminaire

using pin outs as detailed below. Note that only the le hand RJ45 connector can be used for

current sink dimming.

Pin Wire Colour

1 White / Orange

2 Orange

3 White / Green

4 Blue

5 White / Blue

6 Green

7White / Brown

8Brown

RJ45 Pin No Wire Colour Polarity Funcon

3 White / Green +VE Posive Posive (10V) 110V Current Sink Dimming

8Brown Ground (0V) Ground (0V) 110V Current Sink Dimming

RJ45 CONNECTOR (LEFT HAND) - 1-10V CURRENT SINK DIMMING

INSTALLATION

UFO LIGHTING

CONNECTION - FOR 1-10V(CURRENT SINK)OPERATION - CONTINUED

Plug the power supply’s output into the Comet’s power supply input and then connect the

mains plug into a local mains supply. The Comet will initialise and display its current status.

Consult the Troubleshooting and Operation sections in this manual if the Comet does not

power up or operate as expected.

1-10V NOTES

• This is a current sink 1-10V control system. A 10V output from the Pulsar is connected via an

external 1-10V current sink dimmer varying the circuit current to control the dimming only

• Dimming is controlled between maximum light output and approximately 10% at minimum

light output. This minimum value may vary depending on the dimmer used

• Always use an approved CAT5 cable

• Always ensure correct connection polarity

• The Comet 1-10V dimming system has been designed around the UFO CVD3 Current Sink

Electronic Dimmer (See Accessories in Technical Specification section at end of this

document)

• The CVD3 is designed to be fitted to the back of a one gang faceplate

OPERATION

COMET USER GUIDE

USER CONTROLS

Operation of the Comet is carried out via the rear display and associated push button controls

as detailed below:

SELECT / ENTER

MENU SCROLL

DOWN (-)

MENU SCROLL

UP (+)

POWER UP

On power up the display will firstly display as follows and as detailed below:

• The Comet firmware version

• The current status of the unit

Master Dim: 100%

Spd4CW

Pulsar Firmware Version Pulsar Current Status

Comet V1.0.000

The current status used as an example above depicts the light source configured as a DMX

Master, light output 100% (undimmed), this is the factory default setting – see section below.

Once the luminaire is powered up, user controlled manual functions and all programming fea-

tures are available via the four rear panel pushbuttons as detailed in the figure above and the

following Programmable Function Table.

Tabla de contenidos

Otros manuales de Equipo de iluminación de UFO

UFO

UFO MicroLED 4000P Hoja de especificaciones

UFO

UFO GEM SLP-3000M Manual de usuario

UFO

UFO MIC100PT-3 Manual de usuario

UFO

UFO LPV2 Manual de usuario

UFO

UFO MicroLED 4000P Hoja de especificaciones

UFO

UFO Quasar UFOQUA3080-A Manual de usuario

UFO

UFO MicroLED 1000P Hoja de especificaciones

UFO

UFO Vega SLP-2700M Manual de usuario

UFO

UFO MICROLED 2000 Manual de usuario

UFO

UFO IONIC Hoja de especificaciones

UFO

UFO NOVA DMX Hoja de especificaciones

UFO

UFO MIC4000x2 Manual de usuario

UFO

UFO MicroLED 4000P Hoja de especificaciones

UFO

UFO Sirius Series Manual de usuario

UFO

UFO MicroLED 100P Series Hoja de especificaciones

UFO

UFO LUNA SLP-3000M Manual de usuario

UFO

UFO LUNA SLP-3000M Hoja de especificaciones

UFO

UFO MBL1 Manual de usuario

UFO

UFO IP-02 Hoja de especificaciones

UFO

UFO Nova Light Source Hoja de especificaciones

UFO

UFO MicroLED 100PT Hoja de especificaciones

UFO

UFO UFO MIC100P-3 Manual de usuario

UFO

UFO Illuminator 150 CDMXG Manual de usuario

UFO

UFO MicroLED 4000P Hoja de especificaciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario