UDI R/C U64 Manual de usuario
USER
MANUAL
U64
▲This product is suitable for users over 14 years old.
▲Stay away from the rotating propeller.
▲Read the<important statement and safety guidelines >carefully..
Suitable for indoor flight
Slider drone pattern
Motorboat drone pattern
Front
Front
Forward
Backward
Drone-LED
Forward
Backward
OFF ON
Charging port
Propeller A
Propeller B
Propeller A
Propeller B
Charging-LED
OFF ON
Charging port
Ready Before Take Off
Drone preparation
2
①Wings installation
Drone tail installation
Slider drone decoration propeller installation
Slider drone doll and hang lift assembly
①
①
Installation:
Distinguish left and right wings,
aim at the body hole to push until end.
Disassembly:
Apply force to pull the wings
out is fine.
Installation:
Firstly connect the drone tail to the drone body hole and then rotate the
drone tail, push the upper buckle of drone tail to the drone body buckle.
Disassembly:
Pull out the drone tail buckle and then rotate to disassemble.
Installation:
Make sure the slider drone decoration
propeller to aim at the front buckle and push until end.
Disassembly:
Apply force to pull out the decoration
propeller.
Installation:
Hang the doll to the lift and then install the hang lift to the arm slot in
the drone bottom.
Disassembly:
Pull out one side hook of the hang lift, and then another side to
remove the doll.
②
③
④
④
Left Wing
Right Wing
Rear
Front
Slider drone parts installation
③
②
3
②Protection rack installation
Distinguish front and rear of the
motorboat, install the front and
rear guards, and put the hands
to the front guard, finally put on
the doll’s handle.
①Slider drone doll installation
①
Installation:
Make sure distinguish the doll’s front and rear soles, put into the front
toes and then press down the rear foot is fine.
Disassembly:
Lift the rear foot and then pull
out is fine.
②
②
②
②
Front
Front
Rear
Rear
Motorboat parts installation
Charging port
Charging Instruction
Battery power is insufficient in the original plant. It must be charged saturated
before it can be used.
Original charging cable
USB adapter
(Not included)
②①
▲Only use the original charging cable;
suggest select adapters with output
current of 5V 2A .
Connect the original charging cable with the drone, and then connect other USB
charging port. The drone red charging-LED keeps bright when charging and the light
turns green when fully charged.
The drone power button should be
turned off when charging.
4
Left stick /
Trimmer (Press down)
Auto-demo
Take Off / Landing /
Emergency Stop Button
Right Stick
Speed Switch
Heading Hold Mode
Power Switch Motorboat /
Slider drone
Mode Switch
Power-LED
Transmitter preparation
Battery cover
Back side of the transmitter
Battery installation
Open the battery cover on the back side of the transmitter ，according to the "+-"
electrode instruction in the battery groove, place the battery with the same type of
saturated power (battery not include).
3×1.5V AAA
Alkaline Batteries
5
③
①Power on the drone, the drone indicator will change from fast flash to slow flash,
and enter frequency pairing.
The Motorboat are placed
on the horizontal ground.
Hold the drone to keep balance.
* Stay away from the propellers to avoid injury.
②
Short press to open/close
Press the flip switch and select the
corresponding mode.
Flight Operation
Transmitter connect with Drone
Frequency Pairing
Turn on the power on the transmitter, the power-LED will flash quickly.
Pull the left stick until bottom and
then release, and the transmitter
power-LEDwill keep bright and
sound beep to show frequenc
pairing successful.
6
Tip: Do not use the emergency stop function unless in emergency situation.
Take off
Landing
Don’t operate the left stick during landing,
otherwise the current command will automatically fail.
Control stick operation
Left stick
Counterclockwise turn
Clockwise turn
Go up
Go down
Right stick
Fly to the left
Fly to the right
Forward
Backward
After the frequency pairing is successful, press the "take off/land" button, the transmitter
will sound "di", and the drone will automatically rises and flies at an altitude of about 1.2m.
During the flight, press the "take off/land"
button, the transmitter will sound "di",
and the drone will land slowly until landing.
Emergency Stop: During the flight, press " take off/land" button for about 2 seconds,
the transmitter will sound "di.di..." and the drone crashes directly.
7
Press “Automatic show”，the drone
will fly forward and turn back to the
original position.
Auto-demo
Speed mode switch
Press the "H/L" button, the transmitter will sound "di.di.di", to enter High Speed Mode "H".
Press again, the transmitter will sound "di", to enter Low Speed Mode “L”.
Press again, the transmitter will sound “di.di”, to enter Middle Speed Mode “M”.
Medium speed default
Low speed: suitable for beginners to practice
without wind.
Medium speed: suitable for skilled operator
operating in light breeze.
High speed: suitable for professional operation
in outdoor wind resistance.
8
Front Front
Rear
Rear
Heading Hold Mode
①
②
The default setting is NOT Heading Hold Mode.
Heading Hold Mode means that the user can operate the aircraft without having to
distinguish directions. This mode is suitable for beginners, or when it is difficult to
distinguish the forward and backward direction of the drone.
The Heading Hold Mode needs to ensure that the front of the drone
is consistent with the front of the controller, the controller does not
change the direction of the transmitter, and the
drone is always in front of the controller.
When the front of the drone is not consistent
with the pilot's front, the drone will lose
control or be lost.
Start: press the "Heading Hold Mode" button, the
transmitter will sound "didi" to enter the
Heading Hold Mode.
Off: press again, the transmitter will sound
"dididi" to exit the Heading Hold Mode.
9
Only calibrate when motorboat mode
Flying Trimmer
Left and right side flying trimmer
During the flight, if the drone tilts to left, then press down the left stick in the center
button and push the right stick to right to adjust. Otherwise push to left.
Forward / Backward Trimmer
Press down
During the flight, if the drone tilts forward,
press down the left stick in the center button,
and push the right stick backwards.
Otherwise push forwards.
Left and right turning trimmer
During the flight, if the drone head rotates to
left,then press down the left stick in the
center button and push the left stick to right.
Otherwise push to left.
Drone calibration (When abnormal flying)
Tips: When the drone is fiercely impacted or crashed, it may cause the gyro can
not recover and cause difficult control, if so, you can re-pairing&re-calibrate
and put the drone on the level surface.
Unlocking/locking the motor
After successful frequency alignment,
the right stick is pushed to the lower
right corner by 45°, and the drone LED
turns to keep bright after quick flashing,
indicating that the gyroscope has been
calibrated. Release the right stick.
Push the left and right stick inward to the 45 degree angle simultaneously.
①In standby, unlocked the motor and working.
②In Working, locked the motor and stop rotating.
10
Tabla de contenidos
Otros manuales de Zumbido de UDI R/C
UDI R/C
UDI R/C U39S Manual de usuario
UDI R/C
UDI R/C VOYAGER U845Wifi Manual de usuario
UDI R/C
UDI R/C U67 Manual de usuario
UDI R/C
UDI R/C U818A WIFI Manual de usuario
UDI R/C
UDI R/C U61S Manual de usuario
UDI R/C
UDI R/C VOYAGER U845Wifi Manual de usuario
UDI R/C
UDI R/C VOYAGER U845Wifi Manual de usuario
UDI R/C
UDI R/C Neon U51 Manual de usuario
UDI R/C
UDI R/C U59 Manual de usuario
UDI R/C
UDI R/C Swan U42 Manual de usuario
UDI R/C
UDI R/C VOYAGER U845Wifi Manual de usuario
UDI R/C
UDI R/C U88S Manual de usuario
UDI R/C
UDI R/C Swan U42 Manual de usuario
UDI R/C
UDI R/C U95 Manual de usuario
UDI R/C
UDI R/C PEREGRINE Manual de usuario
UDI R/C
UDI R/C U46S Manual de usuario
UDI R/C
UDI R/C U42W Manual de usuario
UDI R/C
UDI R/C U818A WIFI Manual de usuario
UDI R/C
UDI R/C VOYAGER U845Wifi Manual de usuario
UDI R/C
UDI R/C U37 Manual de usuario
