the step-in stakes toward the center. This may help to make the
fence more stable.
NOTE: Make sure there are no green branches or other vegetation
touching any of the orange poly wires as they will weaken the voltage and
deplete the batteries. The bottom poly wire may be touching the ground, as
it is a grounded wire.
2 Installing the blinking LED lights and
electric fence sign
1. Install the batteries (not included) for
the LED lights. Using the bungee cord
and cord lock provided. Secure both of
the LED lights to two top posts that
are not gate posts.
2. Using the ball chains provided hang
the electric fence sign from the top
green wire right next to a post. If
installed next to a post the fence will
not sag.
3 Energizer hookup Important Safety Information
Read Energizer Instructions Carefully.
WARNING: Any alteration to the design of this energizer may cause
serious electrical shock and may void the warranty.
• Install the energizer and the electric fence according to these
installation and operating instructions.
• Inform everyone, especially children, who might possibly come into
contact with the electrically charged fence, about its location and
operation. Do not allow young or infirm persons to use this electric
fence energizer without supervision. Do not allow young children to
play with this energizer or near an electric fence or electrified wires.
• Instruct all persons how to disconnect the energizer in case of
emergency
• Never climb over an electric fence wire while it is electrically
energized
• Never install an electric fence below high-voltage power plant
transmission lines.
• Never use more than one electric fence energizer on the same fence.
• A properly installed ground stake electrically connected to the fence
energizer output ground terminal provides grounding of this product.
The energizer must be grounded. If the energizer should malfunction,
grounding will reduce the risk of electrical shock by providing a path
of low resistance for the electric current.
DANGER: An internal fault on an improperly grounded fence energizer could
result in a risk of harmful electric shock on the electrified fence.
3.1 Insert batteries (See Energizer Instructions)
3.2 Installing your energizer to the electric fence
1. Next to post #1 for the gate but inside the fence,
Drive the 2ft ground stake included with your fence
in to the ground 1ft leaving 1ft out of the ground. The
energizer is designed to sit on this ground stake. On
the back of the energizer there is a ground clip that
directly grounds the energizer when placed on the
ground stake.
2. Attach the red (hot) lead wire to the
energizer by placing the connector
at the end of the wire under the
metal clip on the top of the
energizer.
3. Attach the black (ground) lead wire
to the energizer by placing the
connector at the end of the wire on the ground terminal by removing
the ground terminal knob and attaching the
connector around the bolt. Replace the ground
terminal knob and tighten.
4. Place the energizer on the ground stake by the
energizer’s ground clip. Try to get as much metal
touching as possible.
5. Clip the ground lead wire to the metal tab that is
connected to the green wires towards the bottom of
post #1.
6. Clip the red lead wire
to the top of plastic
post # 1 away from
and in between any
wires. This is done so
that when you turn the
fence on there is no
current running
through the wires.
NOTE: The energizer sits
inside the fence. In order to
get in and out of the enclosure the red lead wire needs to be nonfunctional
by clipping it to the plastic post. The current will not run through the
plastic. Be sure not to touch the metal on the
red plastic alligator clip as it will shock you.
7. Turn on the energizer by turning the knob
all the way on. This energizer has
different settings, but should be turned on
to full power (the P3 setting) when used
with this bear fence. See energizer
instructions.
8. Leave the enclosure and close the gate
(posts #1 and #6). With a shoelace knot
(easy to unfasten), tie the gate posts
together with the cord provided.
9. Unclip the red lead wire from the plastic
post and clip it to the metal tab that is
attached to the orange wires next to post
#1. The fence is now live.
1 . To open the fence to retrieve goods,
unclip the red lead wire and clip it to the
plastic post #1 again taking away the
current. Remember not to touch any of
the metal on the clip as it will shock you.
Questions: Call Toll Free 866 BEAR 911
8:00 AM - :00 PM MST Monday through Friday
ATTENTION! DO NOT RETURN TO STORE!
For product repair or return please call UDAP Industries at 406-494-9292
DISCLAIMER
DO NOT SEEK OUT ENCOUNTERS WITH BEARS. THIS PRODUCT IS A BEAR DETERRENT WHICH MAY
PROTECT USERS FOOD AND EQUIPMENT IN SOME UNEXPECTED CONFRONTATIONS WITH BEARS BUT MAY
NOT BE EFFECTIVE IN ALL SITUATIONS OR PREVENT ALL LOSS OR DAMAGES. READ CAREFULLY THE
ENTIRE INSTRUCTIONS UPON PURCHASE & BEFORE TAKING THIS PRODUCT INTO AREAS WHERE BEARS
MIGHT BE ENCOUNTERED. KEEP OUT OF REACH OF CHILDREN. To the e tent allowed by law, UDAP Industries,
Inc. shall not be liable for damage, injury, loss, direct or consequential including death arising out of the use of, or
inability to use this product.
PepperPower.com
