UCHIDA AeroCut Velocity Manual de usuario
AeroCut Velocity OPERATION MANUAL
2
・Use machine only after reading the "Safety Instructions" given below carefully.
・These safety instructions are given to ensure that the machine will be used safely and
properly and to prevent operators from sustaining harm and injuries.
Explanation of markings
Marking Meaning of marking
Warning This symbol stands for immediate danger threatening the life and health of
persons. Disregarding these instructions may cause severe damage to
health and even serious injuries.
Caution This symbol stands for an endangering situation that may occur.
Disregarding these instructions may lead to slight injuries or damage to
property.
Definition of Symbols and Notes
In this manual the following names and signs stand for possible dangers.
Caution
This symbol stands for an endangering situation that may occur.
Disregarding these instructions may lead to slight injuries or
damages to property.
Note
This symbol stands for notes, operational hints, and other useful
information.They are convenient for exploiting the machine’s functional
abilities.
SAFETY INSTRUCTIONS
Explanations of the illustrations used in the Safety Instructions are given as follows:
1. Don't open the cover of the equipment. There is a danger of receiving an injury or electric
shock.
2. Don't touch any rotating part. There is a danger of receiving an injury.
3. Don’t put hands inside work area. May result in severe injury.
Warning
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
AeroCut Velocity OPERATION MANUAL
3
1. Don't put a hand into the cover or a clearance between parts. There is a danger of
receiving an injury.
2. Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts of
the machine. There is a danger of receiving an injury.
3. Don't touch the blade point of the cutter. There is a danger of receiving an injury.
4. Turn off the power supply beforehand when setting the feed table. There is a danger of
receiving an injury.
5. Turn off the power supply beforehand when removing paper scraps. There is a danger of
receiving an injury.
6. Do not exceed the MAX level when stacking the paper. Exceeding it may cause a
mechanical failure.
7. Turn off the power supply beforehand when starting maintenance or inspection. There is a
danger of receiving an injury.
8. When you install a machine, please install to a place with no dust, and the place which is
not influenced with a liquid. It becomes the cause of failure if the installation method is
mistaken.
9. When you put a machine into operation, please change into the state where all covers
were closed. If it works where a cover is opened, there is fear of an injury.
Caution
Before use
Read this "Operation Manual" carefully before use. In particular, be sure to read "Safety
Instructions" (page 2 to page 3) to ensure that the machine will be used properly.
Keep the manual at an appointed place with care so that it may be accessible whenever
necessary.
The specifications of this product are subject to change for improvement. Therefore, don't
mistake the "Operation Manual" of one product of the same model for that of another
because descriptions in the "Operation Manual" of products of the same model may differ.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
AeroCut Velocity OPERATION MANUAL
4
Contents
1Introduction..................................................................................6
1.1 Names of parts........................................................................................................6
1.2 Accessories.............................................................................................................8
1.3 Touch panel.............................................................................................................8
1.4 Paper weight / quality..............................................................................................9
2Operating instructions ...............................................................10
2.1 Lock a caster brake...............................................................................................10
2.2 Turning the power on.............................................................................................10
2.3 Initial position.........................................................................................................11
2.4 Input ......................................................................................................................11
2.5 Set.........................................................................................................................12
2.6 Paper setting.........................................................................................................12
2.7 Stacker and Waste box settings ............................................................................13
2.8 Start.......................................................................................................................15
2.9 Stop.......................................................................................................................15
2.10 Waste disposal...................................................................................................17
2.11 Power off ...............................................................................................................17
3Cut pattern input........................................................................18
3.1 Outline...................................................................................................................18
3.2 PRESET................................................................................................................18
3.3 MANUSET.............................................................................................................20
3.4 FLEX MODE..........................................................................................................23
3.5 SAVE / READ........................................................................................................25
4How to use options....................................................................27
4.1 How to attach the Y-perforator...............................................................................27
4.2 How to adjust the Y-perforation location................................................................28
4.3 How to adjust the depth of Y-perforation................................................................29
5Adjustment ................................................................................30
5.1 Adjustments on the paper feed section .................................................................30
5.2 Speed change .......................................................................................................32
5.3 Skew adjustment...................................................................................................33
5.4 Creaser adjustment...............................................................................................33
5.5 Fine adjustments on processing positions.............................................................34
5.5.1 In cases cutting positions don’t match to image positions..............................34
5.5.2 If the cut measurement does not match the input value.................................35
6Manual control...........................................................................37
6.1 Manual control screen...........................................................................................37
AeroCut Velocity OPERATION MANUAL
5
6.2 Paper jam..............................................................................................................37
7Error messages.........................................................................38
8Troubleshooting.........................................................................43
9Product specifications ...............................................................45
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
AeroCut Velocity OPERATION MANUAL
6
1 Introduction
1.1 Names of parts
Stacke
r
Creaser
Guillotine
Waste box
Caster
Power switch
Inlet
Skew adjustment dial
Safety cover
Feed table
Touch panel
Gutter slitter unit Margin slitter unit
AeroCut Velocity OPERATION MANUAL
7
Warning
Don’t put hands inside work area.
May result in severe injury.
Don't touch any rotating part. There is a danger of
receiving an injury.
Don't open the cover of the equipment. There is a
danger of receiving an injury or electric shock.
Caution
Don't touch the blade point of the cutter. There is a
danger of receiving an injury.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
AeroCut Velocity OPERATION MANUAL
8
1.2 Accessories
x2
Waste box
Electric
Power cord
Paper guide
(Large)
Paper guide
(Small)
Template
x2
x2
Card stacker
Stacker end
Business card
Partition
Hexagonal wrench
Spanner
Upper suction shutter
1.3 Touch panel
Home screen
END Page 15
START
Page 15
Clear
Page 15
STOP
Manual Speed
Page 30
Manu Set
Page 20
Preset
Page 18
Quantity
Page 15 Cutmark
Page 11
Page 15
Flex Mode
Page 23
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
AeroCut Velocity OPERATION MANUAL
9
Manu Set screen
SAVE
Page 25
READ
Page 25
Flex Mode screen
SAVE
Page 25
READ
Page 25
Manual speed screen
CUTTER
(Guillotine)
Page 37
TABLE
Page 37
Inching
Page 37
Double feed
Page 30
VACUUM
Page 30
BLOW
Page 30
CREASE
Page 37
BLOW
Page 30
SPEED
Page32
PAPER FEED WORK TIME
Page 30 CREASE
Page 33
A
DJUST
Page 35
1.4 Paper weight / quality
Use suitable paper stocks which weight is 120 to 400gsm(0.005”-0.016”).
These paper stocks are not suitable in use.
・Papers that has heavily electric static charged. It may cause miss-feed, double feed
or paper jam.
・Papers that are more than 0.125” curled or waved. It may cause miss-feed, double
feed or paper jam.
・Papers that have ink or toner not fused properly. It may cause contaminating the work
and the machine.
・Papers that are too slippery. It may cause miss-feed or inaccurate results.
・Prints that are shrank, stretched or skewed inconsistently. It may cause inaccurate
results.
AeroCut Velocity OPERATION MANUAL
10
2 Operating instructions
2.1 Lock a caster brake
2.2 Turning the power on
Caster
Unlock
Lock
A
C 110-120V
50/60Hz
400W
Electric power cord
Power switch
ON
OFF
Opening screen
Power on
Home screen
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Tabla de contenidos
Otros manuales de Cortador de UCHIDA
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
